Pest - Main Tray Pick Clutch Disconnect - Xerox ColorQube 8570 Service Manual

99,019 PEST - Main Tray Pick Clutch Disconnect

The Main Tray Pick Clutch error has occurred. The Clutch is not drawing the expected power
from the Power Supply. The following troubleshooting applies to this error.
Table 1 Applicable Fault Code
99,019 PEST - Main Tray Pick Clutch Disconnect
Initial Actions
• Reboot the printer and verify the error persists.
• Check the Clutch's wiring connection.
• If the problem persists, perform the following procedure.
Troubleshooting Procedure
Applicable Parts (Chapter 5 - Parts List)
• Media Drive with 2 Clutches, PL 5.1 Item 5
• Electronics Module, PL 5.1 Item 5
• Power Control Board, PL 5.1 Item 8
• Harness, Left Side Power Control,
Wiring and Plug/Jack References (Chapter 7 - Wiring Data)
• Figure 2, Left Side Wire Routing
• Figure 3, Left Side Electronics Module P/J Locations
• Figure 4, Optional Tray, Clutches, Solenoids, Tray 2 Lift Motor
Procedure
Check the Main Tray Pick Clutch wiring harness connector P/J109. Is
secure and undamaged?
Y N
Reseat and/or replace the wiring harness.
Check resistance on the Main Tray Deskew Clutch wiring harness connector P/J109. Is
open or shorted?
Y N
Check resistance on the Left Side Wiring Harness
shorted?
Y N
Troubleshooting complete.
Replace the Left Side Wiring Harness.
Replace the Media Drive (REP 5.5). Does the error persist?
Y N
Troubleshooting complete.
Replace the Power Control Board (REP
Xerox Internal Use Only - Revised, 3rd Revision
ColorQube 8570/8870 Service Manual
PL 5.1 Item 17
the
P/J302 (pin 21). Is it
5.6) (Electronics Module).
99,020 PEST - Multipurpose Tray Pick Solenoid Disconnect
The Multipurpose Tray Pick Solenoid error has occurred. The Solenoid is not drawing the
expected power from the Power Supply. The following troubleshooting applies to this error.
99,020 PEST - Multipurpose Tray Pick Solenoid Disconnect
Initial Actions
• Reboot the printer and verify the error persists.
• Check the Solenoid's wiring connection.
• If the problem persists, perform the following procedure.
Troubleshooting Reference
Applicable Parts (Chapter 5 - Parts List)
• Tray 1 Pick Solenoid,
• Electronics Module,
• Power Control Board,
• Harness, Left Side Power Control,
Wiring and Plug/Jack References (Chapter 7 - Wiring Data)
• Figure 2, Left Side Wire Routing
• Figure 3, Left Side Electronics Module P/J Locations
• Figure 4, Optional Tray, Clutches, Solenoids, Tray 2 Lift Motor
Procedure
connection Check the Tray 1 Pick Solenoid wiring harness connector P/J110. Is the connection secure
and undamaged?
Y N
Reseat and/or replace the wiring harness.
it Check resistance on the Tray 1 Pick Solenoid wiring harness connector P/J110. Is it open or
shorted?
Y N
open or Check resistance on the Left Side Wiring Harness
shorted?
Y N
Troubleshooting complete.
Replace the Left Wiring Harness.
Replace the Tray 1 Pick Solenoid
Y N
Troubleshooting complete.
Replace the Power Control Board
October 2012
2-77
Table 1 Applicable Fault Code
PL 4.1 Item 3
PL 5.1 Item 1
PL 5.1 Item 8
PL 5.1 Item 17
P/J302 (pin 23). Is
(REP 4.3). Does the error persist?
(REP 5.6) (Electronics Module).
it open or
Fault Messages and Codes
99,019, 99,020