Paper Jam - Open Exit Door B To Clear (No Jam Is Present And Message Won't Clear) - Xerox ColorQube 8570 Service Manual

Paper Jam - Open Exit Door B to Clear (no jam is present
and message won't clear)
A paper jam has occurred. The following troubleshooting procedure applies to this error.
Initial Actions
• Check the paper path for obstructions.
• If the problem persists, perform the following procedure.
Troubleshooting Reference
Applicable Part (Chapter 5 - Parts List)
• Exit Module Sensor Assy, PL 6.1 Item 9
Wiring and Plug/Jack References (Chapter 7 - Wiring Data)
• Figure 5, Top Front Wire Routing
• Figure 8, I/O Board, Sensors (1 of 2)
Procedure
Check the Top Door sensor wiring harness connector
Is the connection secure and undamaged?
Y N
Reseat and/or replace the wiring harness.
Check the Strip Sensor wiring for damage or being unplugged. Check that Strip Flag can move
freely (is not stuck). Does the Strip Flag move freely and is the connection secure and
undamaged?
Y N
Troubleshooting complete.
Replace the Exit Module Sensor Assembly.
Xerox Internal Use Only - Revised, 3rd Revision
ColorQube 8570/8870 Service Manual
P/J116 for damage or being unplugged,
October 2012
Tray 2 Empty (when it has paper)
A Tray 2 error has occurred. The following troubleshooting procedure applies to this error.
Initial Actions
• Remove any paper from Tray 2.
• Inspect the Paper Tray for damage.
• Reload Tray 2 with fresh paper and confirm the Paper Guides are set correctly.
Troubleshooting Reference
Applicable Parts (Chapter 5 - Parts List)
• Preheater and Deskew Assembly,
• Tray 2 Lift Motor, PL 4.1 Item 6
• I/O Board, PL 5.1 Item 10
• Tray Lift Sensor, PL 6.1 Item 3
Wiring and Plug/Jack References (Chapter 7 - Wiring Data)
• Figure 2, Left Side Wire Routing
• Figure 3, Front Side Wire Routing
• Figure 4, Optional Tray, Clutches, Solenoids, Tray 2 Lift Motor
• Figure 9, I/O Board, Sensors (2 of 2)
Procedure
If the I/O Board has been recently removed, check that the ground plane on the top left corner
has been properly installed on top of the I/O Board instead of underneath. Otherwise, remove
the Preheater (REP 2.20) and check that wires are not blocking the Tray Lift Sensor (orange
flag) located on the chassis base under the Preheater. Is the Tray Lift Sensor blocked by
the wiring harnesses?
Y N
Check that the Tray Lift Sensor wiring harness
are undamaged. Is the connection secure and undamaged?
Y N
Reseat and/or replace the wiring harness.
Check that the Tray Lift Motor wiring harness connector
is plugged in and wires are undamaged. Is the connection secure and undamaged?
Y N
Reseat and/or replace the wiring harness.
Replace the Tray 2 Lift Motor (REP
Move the wiring harnesses away from the Tray Lift Sensor. Does the error persist?
Y N
Troubleshooting complete.
Replace the Tray Lift Sensor. Does the error persist?
Y N
Troubleshooting complete.
Replace the I/O Board (REP 5.10).
Paper Jam - Open Exit Door B to Clear, Tray 2 Emp-
2-93
PL 2.1 Item 20
P/J126 is properly plugged in and wires
P/J108 (on the left side chassis)
4.6).
Fault Messages and Codes