Omron SYSDRIVE 3G3RV Series User Manual page 439

No.
Operation selection at PG open cir-
F1-02
cuit (PGO)
Operation selection at overspeed
F1-03
(OS)
F1-04 Operation selection at deviation
F1-05 PG rotation
PG division rate (PG pulse moni-
F1-06
tor)
Integral value during accel/decel
F1-07
enable/disable
F1-08 Overspeed detection level
F1-09 Overspeed detection delay time
Excessive speed deviation detec-
F1-10
tion level
Excessive speed deviation detec-
F1-11
tion delay time
F1-12 Number of PG gear teeth 1
F1-13 Number of PG gear teeth 2
F1-14 PG open-circuit detection time
F4-01 Channel 1 monitor selection
F4-02 Channel 1 gain
F4-03 Channel 2 monitor selection
F4-04 Channel 2 gain
F4-05 Channel 1 output monitor bias
F4-06 Channel 2 output monitor bias
Analog output signal level for
F4-07
channel 1
Analog output signal level for
F4-08
channel 2
F5-01 Not used
F5-02 Not used
F5-03 Not used
F5-04 Not used
F5-05 Not used
F5-06 Not used
F5-07 Not used
F5-08 Not used
F5-09 Not used
DeviceNet fault operation selec-
F6-01
tion
Communications external fault
F6-02
input detection method selection
Communications external fault
F6-03
input operation selection
F6-04 Not used
Display unit selection for current
F6-05
monitor
H1-01 Terminal S3 function selection
H1-02 Terminal S4 function selection
H1-03 Terminal S5 function selection
-16
10
Table 10.1 Parameters (Continued)
Fac-
Name tory
Setting
1
1
3
0
1
0
115
1.0
10
0.5
0
0
2.0
2
1.00
3
0.50
0.0
0.0
0
0
0
1
2
4
6
37
0F
0F
0
1
0
1
0
0
24
14
*8
3 (0)
Set-
No.
ting
H1-04 Terminal S6 function selection
H1-05 Terminal S7 function selection
H2-01 Terminal M1-M2 select
Terminal P1 function select (open
collector)
H2-02
Terminal M3-M4 function select
(contact)
Terminal P2 function select (open
collector)
H2-03
Terminal M5-M6 function select
(contact)
H3-01 Signal select terminal A1 (voltage)
H3-02 Gain (terminal A1)
H3-03 Bias (terminal A1)
Multi-function analog input termi-
H3-08
nal A2 signal level selection
Multi-function analog input termi-
H3-09
nal A2 function selection
H3-10 Gain (terminal A2)
H3-11 Bias (terminal A2)
H3-12 Analog input filter time constant
H3-13 Terminal A1/A2 switching
H4-01 Monitor selection (terminal FM)
H4-02 Gain (terminal FM)
H4-03 Bias (terminal FM)
H4-04 Monitor selection (terminal AM)
H4-05 Gain (terminal AM)
H4-06 Bias (terminal AM)
Analog output 1 signal level selec-
H4-07
tion
Analog output 2 signal level selec-
H4-08
tion
H5-01 Slave address
H5-02 Communication speed selection
H5-03 Communication parity selection
Stopping method after communi-
H5-04
cation error
Communication error detection
H5-05
selection
H5-06 Send wait time
H5-07 RTS control ON/OFF
H6-01 Pulse train input function selection
H6-02 Pulse train input scaling
H6-03 Pulse train input gain
H6-04 Pulse train input bias
H6-05 Pulse train input filter time
H6-06 Pulse train monitor selection
H6-07 Pulse train monitor scaling
Fac-
Name tory
Setting
*8
4 (3)
*8
6 (4)
0
1
2
0
100.0
0.0
2
0
100.0
0.0
0.00
0
2
1.00
0.0
3
0.50
0.0
0
0
1F
3
0
3
1
5
1
0
1440
100.0
0.0
0.10
2
1440
Set-
ting