Subaru Legacy 2004 Service Manual page 994

Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step
16 CHECK POOR CONTACT.
Check poor contact in connector between
ECM and electronic throttle control.
17 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from electronic
throttle control.
4) Measure the resistance between ECM con-
nector and electronic throttle control connector.
Connector & terminal
(B136) No. 35 — (E57) No. 3:
(B136) No. 18 — (E57) No. 6:
(B136) No. 29 — (E57) No. 4:
18 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Connect the ECM connector.
2) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 3 — Engine ground:
19 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to ON.
2) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 5 (+) — Engine ground (
20 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
Measure the voltage between electronic throt-
tle control connector and engine ground.
Connector & terminal
(E57) No. 6 (+) — Engine ground (
(E57) No. 4 (+) — Engine ground (
21 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Remove the ECM.
3) Measure the resistance between ECM con-
nectors.
Connector & terminal
(B136) No. 18 — (B136) No. 16:
(B136) No. 29 — (B136) No. 16:
22 CHECK SENSOR OUTPUT.
1) Turn the ignition switch to OFF.
2) Connect the connectors except for the elec-
tric control throttle relay.
3) Turn the ignition switch to ON.
4) Read the data of main throttle sensor signal
using Subaru Select Monitor.
23 CHECK SENSOR OUTPUT.
Read the data of sub throttle sensor signal
using Subaru Select Monitor.
Check
Is there poor contact?
Is the resistance less than 1
!?
Is the resistance less than 5
!?
Is the voltage less than 10 V?
"
):
Is the voltage less than 10 V?
"
):
"
):
Is the resistance more than 1
M!?
Is the voltage 0.81 — 0.87 V? Go to step 23.
Is the voltage 1.64 — 1.70 V? Go to step 24.
EN(H4SO 2.5)(diag)-235
ENGINE (DIAGNOSTICS)
Yes
Repair the poor Go to step 22.
contact.
Go to step 18. Repair the open
circuit of harness
connector.
Go to step 19. Repair the poor
contact in ECM
connector.
Replace the ECM
if defective. <Ref.
to FU(H4SO 2.5)-
36, Engine Con-
trol Module
(ECM).>
Go to step 20. Repair the battery
short circuit in har-
ness between
ECM connector
and electronic
throttle control
connector.
Go to step 21. Repair the short
circuit in harness
between ECM
connector and
electronic throttle
control connector.
Go to step 22. Repair the short
circuit to sensor
power supply.
Repair the poor
contact of elec-
tronic throttle con-
trol connector.
Replace the elec-
tronic throttle con-
trol if defective.
Repair the poor
contact in ECM
connector.
Replace the elec-
tronic throttle con-
trol if defective.
No