Mitsubishi Electric FR-F820-00077 Instruction Manual page 206

Parameter List
(A) Application parameters
Parameters to set a specific application.
Pr.
Pr. Name
group
Electronic bypass sequence
A000 135
selection
A001 136 MC switchover interlock time
A002 137 Start waiting time
A003 138 Bypass selection at a fault
Automatic switchover frequency
A004 139
from inverter to bypass operation
Automatic switchover frequency
A005 159 range from bypass to inverter
operation
A006 248 Self power management selection
A007 254 Main circuit power OFF waiting time
A300 592 Traverse function selection
A301 593 Maximum amplitude amount
Amplitude compensation amount
A302 594
during deceleration
Amplitude compensation amount
A303 595
during acceleration
A304 596 Amplitude acceleration time
A305 597 Amplitude deceleration time
A400 578 Auxiliary motor operation selection
A401 579 Motor connection function selection
A402 580 MC switching interlock time
A403 581 Start waiting time
Auxiliary motor connection-time
A404 582
deceleration time
Auxiliary motor disconnection-time
A405 583
acceleration time
A406 584 Auxiliary motor 1 starting frequency
A407 585 Auxiliary motor 2 starting frequency
A408 586 Auxiliary motor 3 starting frequency
Auxiliary motor 1 stopping
A409 587
frequency
Auxiliary motor 2 stopping
A410 588
frequency
Auxiliary motor 3 stopping
A411 589
frequency
A412 590 Auxiliary motor start detection time
A413 591 Auxiliary motor stop detection time
A414 1376 Auxiliary motor stopping level
A420 1469 Number of cleaning times monitor
A421 1470 Number of cleaning times setting
A422 1471 Cleaning trigger selection
A423 1472 Cleaning reverse rotation frequency
Cleaning reverse rotation operation
A424 1473
time
A425 1474 Cleaning forward rotation frequency
Cleaning forward rotation operation
A426 1475
time
A427 1476 Cleaning stop time
Tab. 5-13: Application parameters (1)
5 - 34
Pr.
Pr.
group
A428 1477
Refer to
A429 1478
page
A430 1479
5-333
A440 1361
5-333
A441 1362
5-333
A442 1370
5-333
A443 1371
5-333
A444 1372
5-333
A445 1373
5-342
A446 1369
5-342
5-346
A447 1363
5-346
A448 1364
A449 1365
5-346
A450 1374
5-346
A451 1375
5-346
5-346
A452 1377
5-392
A453 1378
5-392
A454 1379
5-392
A455 1380
5-392
A456 1381
5-392
A600 759
5-392
A601 131
5-392
A602 132
5-392
A603 553
5-392
A604 554
5-392
A607 1015
A610 128
5-392
A611 133
5-392
A612 127
5-392
A613 129
5-392
A614 130
5-404
A615 134
5-348
A616 760
5-348
A617 761
5-348
A618 762
5-348
A619 763
5-348
A620 764
5-348 A621 575
A622 576
5-348
A623 577
5-348
Tab. 5-13:
Name
Cleaning acceleration time
Cleaning deceleration time
Cleaning time trigger
Detection time for PID output hold
PID output hold range
Detection time for PID limiting
operation
PID upper/lower limit prewarning
level range
PID measured value control set
point change amount
PID measured value control set
point change rate
Check valve closing completion
frequency
PID Priming time
Stirring time during sleep
Stirring interval time
Auxiliary pressure pump operation
starting level
Auxiliary pressure pump operation
stopping level
PID input pressure selection
PID input pressure warning level
PID input pressure fault level
PID input pressure warning set point
change amount
PID input pressure fault operation
selection
PID unit selection
PID upper limit
PID lower limit
PID deviation limit
PID signal operation selection
Integral stop selection at limited
frequency
PID action selection
PID action set point
PID control automatic switchover
frequency
PID proportional band
PID integral time
PID differential time
Pre-charge fault selection
Pre-charge ending level
Pre-charge ending time
Pre-charge upper detection level
Pre-charge time limit
Output interruption detection time
Output interruption detection level
Output interruption cancel level
Application parameters (2)
Parameters
Refer to
page
5-348
5-348
5-348
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-404
5-381
5-353
5-353
5-353
5-353
5-167
5-353
5-353
5-353
5-353
5-353
5-353
5-385
5-385
5-385
5-385
5-385
5-353
5-353
5-353