Hitachi WJ200-001S Instruction Manual page 655

Ver.3− − − − 146
O O O O ption ption T T T T erminal erminal
ption ption erminal erminal
C C C C ode ode ode ode S S S S ymbol ymbol ymbol ymbol
24 24 FA4
24 24
FA5
25 25 25 25
2 2 2 2 6 6 6 6 OL2
2 2 2 2 7 7 7 7 ODc
2 2 2 2 8 8 8 8 OIDc
3 3 3 3 1 1 1 1 FBV
NDc
32 32 32 32
33 33 LOG1
33 33
34 34 34 34 LOG2
LOG3
35 35 35 35
3 3 3 3 9 9 9 9 WAC
WAF
4 4 4 4 0 0 0 0
4 4 4 4 1 1 1 1 FR
42 42 42 42 OHF
LOC
43 43 43 43
44 44 MO1
44 44
45 45 MO2
45 45
O O O O utput Function Summary Table utput Function Summary Table
utput Function Summary Table utput Function Summary Table
F F F F unction Name unction Name unction Name unction Name
Frequency Arrival ON
Type 4–Over frequency
OFF
Frequency Arrival ON
Type 5–Set frequency
OFF
Overload Advance ON
Notice Signal 2
OFF
Analog Voltage Input ON
Disconnect Detection
OFF
Analog Current input ON
Disconnect Detection
OFF
PID Second Stage ON
Output
OFF
Network Disconnect ON
Detection
OFF
Logic Output Function ON
1
OFF
Logic Output Function ON
2
OFF
Logic Output Function ON
3
OFF
Capacitor Life Warning ON
Signal
OFF
Cooling Fan Warning ON
Signal
OFF
Starting Contact ON
Signal
OFF
Heat Sink Overheat ON
Warning
OFF
Low load detection ON
OFF
General Output 1 ON
OFF
General Output 2 ON
OFF
D D D D escription escription escription escription
When output to motor is at or above the set
freq., even if in accel (C C C C 0 0 0 0 45 45 45) or decel (C C C C 0 0 0 0 4 4 4 4 6 6 6 6 ) 45
ramps
When output to motor is OFF, or at a level below
the set frequency
When output to motor is at the set frequency,
during accel (C C C C 0 0 0 0 45 45 45 45) and decel (C C C C 0 0 0 0 4 4 4 4 6 6 6 6 ).
When output to motor is OFF, or is not at a level
of the set frequency
When output current is more than the set
threshold (C C C C 111 111) for the overload signal
111 111
When output current is less than the set
threshold for the deviation signal
When the [O] input value < b b b b 0 0 0 0 7 7 7 7 0 0 0 0 setting (signal
loss detected)
When no signal loss is detected
When the [OI] input value < b b b b 0 0 0 0 7 7 7 7 1 1 1 1 setting (signal
loss detected)
When no signal loss is detected
Transitions to ON when the inverter is in RUN
Mode and the PID Process Variable (PV) is less
than the Feedback Low Limit (C C C C 0 0 0 0 53
Transitions to OFF when the PID Process
Variable (PV) exceeds the PID High Limit
(C C C C 0 0 0 0 52 52 52 52), and transitions to OFF when the
inverter goes from Run Mode to Stop Mode
When the communications watchdog timer
(period specified by C C C C 0 0 0 0 77 77 77) has time out 77
When the communications watchdog timer is
satisfied by regular communications activity
When the Boolean operation specified by C C C C 1 1 1 1 43
has a logical "1" result
When the Boolean operation specified by C C C C 1 1 1 1 43
has a logical "0" result
When the Boolean operation specified by C C C C 1 1 1 1 4 4 4 4 6 6 6 6
has a logical "1" result
When the Boolean operation specified by C C C C 1 1 1 1 4 4 4 4 6 6 6 6
has a logical "0" result
When the Boolean operation specified by C C C C 1 1 1 1 4 4 4 4 9 9 9 9
has a logical "1" result
When the Boolean operation specified by C C C C 1 1 1 1 4 4 4 4 9 9 9 9
has a logical "0" result
Lifetime of internal capacitor has expired.
Lifetime of internal capacitor has not expired.
Lifetime of cooling fan has expired.
Lifetime of cooling fan has not expired.
Either FW or RV command is given to the
inverter
No FW or RV command is given to the inverter,
or both are given to the inverter
Temperature of the heat sink exceeds a specified
value (C C C C 0 0 0 0 6 6 6 6 4 4 4 4 )
Temperature of the heat sink does not exceed a
specified value (C C C C 0 0 0 0 6 6 6 6 4 4 4 4 )
Motor current is less than the specified value
(C C C C 0 0 0 0 3 3 3 3 9 9 9 9 )
Motor current is not less than the specified
value (C C C C 0 0 0 0 3 3 3 3 9 9 9 9 )
General output 1 is ON
General output 1 is OFF
General output 2 is ON
General output 2 is OFF
53)
53 53
43 43 43
43
43 43