Hitachi WJ200-001S Instruction Manual page 642

Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
b b b b 1 1 1 1 0 0 0 0 6 6 6 6
Free V/F setting,
freq.4
b b b b 1 1 1 1 0 0 0 0 7 7 7 7
Free V/F setting,
voltage.4
b b b b 1 1 1 1 0 0 0 0 8 8 8 8
Free V/F setting,
freq.5
b b b b 1 1 1 1 0 0 0 0 9 9 9 9
Free V/F setting,
voltage.5
b b b b 11 110 0 0 0 11 11
Free V/F setting,
freq.6
b b b b 111 111 111 111
Free V/F setting,
voltage.6
b b b b 11 112 2 2 2
11 11
Free V/F setting,
freq.7
b b b b 11 113 3 3 3
11 11
Free V/F setting,
voltage.7
Brake control
b b b b 1 1 1 1 2 2 2 2 0 0 0 0
enable
b b b b 1 1 1 1 2 2 2 2 1 1 1 1 Brake Wait Time
for Release
b b b b 1 1 1 1 22 22 22 22 Brake Wait Time
for Acceleration
Brake Wait Time
b b b b 1 1 1 1 23 23 23 23
for Stopping
b b b b 1 1 1 1 24 24 24 24 Brake Wait Time
for Confirmation
b b b b 1 1 1 1 25 25 Brake release
25 25
freq.
b b b b 1 1 1 1 2 2 2 2 6 6 6 6 Brake release
current
b b b b 1 1 1 1 2 2 2 2 7 7 7 7 Braking freq.
setting
b b b b 1 1 1 1 3 3 3 3 0 0 0 0 Deceleration
overvoltage
suppression
enable
b b b b 1 1 1 1 3 3 3 3 1 1 1 1 Decel. overvolt.
suppress level
Decel. overvolt.
b b b b 1 1 1 1 32 32 32 32
suppress const.
b b b b 1 1 1 1 33 33 33 33 Decel. overvolt.
suppress
proportional gain
Decel. overvolt.
b b b b 1 1 1 1 34 34 34 34
suppress integral
time
b b b b 1 1 1 1 45 45 GS input mode
45 45
Display
b b b b 1 1 1 1 5 5 5 5 0 0 0 0
ex.operator
connected
b b b b 1 1 1 1 6 6 6 6 0 0 0 0 1st parameter of
Dual Monitor
2nd parameter of
b b b b 1 1 1 1 6 6 6 6 1 1 1 1
Dual Monitor
" " " " b b b b " " " " Function Function
Function Function
D D D D escription
Set range, value of b b b b 1 1 1 1 0 0 0 0 4 4 4 4 to b b b b 1 1 1 1 0 0 0 0 8 8 8 8
Set range, 0 to 800V
Set range, value of b b b b 1 1 1 1 0 0 0 0 8 8 8 8 to b b b b 11
Set range, 0 to 800V
Set range, value of b b b b 1 1 1 1 0 0 0 0 8 8 8 8 to b b b b 11
Set range, 0 to 800V
Set range, b b b b 11 110 0 0 0 to 400(580) 11 11
Set range, 0 to 800V
Two option codes:
00 00 00 00 ... Disable
0 0 0 0 1 1 1 1 ... P012=00:Enable/
P012=02:Enable with DC breaking at positioning end
0 0 0 0 2 2 2 2 ... P012=00:Enable/
P012=02:Enable without DC breaking at positioning end
Set range: 0.00 to 5.00 sec
Set range: 0.00 to 5.00 sec
Set range: 0.00 to 5.00 sec
Set range: 0.00 to 5.00 sec
Set range: 0.00 to 400.0(580.0)
Set range: 0.00 to 200% of inverter rated current
Set range: 0.00 to 400.0(580.0)
00 00 ... Disabled
00 00
0 0 0 0 1 1 1 1 ... Enabled
0 0 0 0 2 2 2 2 ... Enabled with accel.
DC bus voltage of suppression. Range is:
200V class ... 330 to 395
400V class ... 660 to 790
Accel. rate when b130=02.
Set range: 0.10 to 30.00 sec.
Proportional gain when b130=01. Range is: 0.00 to 5.00
Integration time when b130=01. Range is: 0.0 to 150.0
Two option codes:
00 ... No trip (Hardware shutoff only) 00
00 00
0 0 0 0 1 1 1 1 ... Trip
When an external operator is connected via RS-422 port, the
built-in display is locked and shows only one "d" parameter
configured in:
d d d d 00 00 001 1 1 1 to d d d d 0 0 0 0 3 3 3 3 0 0 0 0 00
Set any two "d" parameters in b160 and b161, then they can be
monitored in d050. The two parameters are switched by
up/down keys.
Set range: d d d d 00 001 1 1 1 to d d d d 0 0 0 0 3 3 3 3 0 0 0 0 00 00
escription escription escription
110 0 0 0
11 11
112 2 2 2 11 11
*1
*1 Hz
*1 Hz
Ver.3− − − − 133
D D D D efaults efaults
efaults efaults
A A A A B B B B
Initial data Initial data Initial data Initial data Units Units Units Units
0. Hz
0.0 V
0. Hz
0.0 V
0. Hz
0.0 V
0. Hz
0.0 V
00 -
0.00 s
0.00 s
0.00 s
0.00 s
0.00 Hz
Rated
A
current
0.00 Hz
00
−
380
V
/760
1.00 s
0.20
−
1.0 s
00 -
001
−
001
−
002
−