Hitachi WJ200-001S Instruction Manual page 654

O O O O utput Function Summary Table utput Function Summary Table utput Function Summary Table utput Function Summary Table – This table shows all functions for the logical outputs (terminals [11],
[12] and [AL]) at a glance. Detailed descriptions of these functions, related parameters and settings, and
example wiring diagrams are in "Using Intelligent Output Terminals" on page 39.
O O O O ption ption T T T T erminal erminal
ption ption erminal erminal
F F F F unction Name unction Name unction Name unction Name
C C C C ode ode ode ode S S S S ymbol ymbol ymbol ymbol
00 00 RUN Run Signal
00 00
FA1 Frequency Arrival
0 0 0 0 1 1 1 1
Type 1–Constant Speed
0 0 0 0 2 2 2 2 FA2 Frequency Arrival
Type 2–Over frequency
OL Overload Advance
0 0 0 0 3 3 3 3
Notice Signal 1
0 0 0 0 4 4 4 4 OD Output Deviation
for PID Control
0 0 0 0 5 5 5 5 AL Alarm Signal
0 0 0 0 6 6 6 6 FA3 Frequency Arrival
Type 3–Set frequency
0 0 0 0 7 7 7 7 OTQ Over/under Torque
Signal
0 0 0 0 9 9 9 9 UV Undervoltage
1 1 1 1 0 0 0 0 TRQ Torque Limited Signal
RNT Run Time Expired
11 11 11 11
1 1 1 1 2 2 2 2 ONT Power ON time
Expired
1 1 1 1 3 3 3 3 THM Thermal Warning
BRK Brake Release Signal
1 1 1 1 9 9 9 9
2 2 2 2 0 0 0 0 BER Brake Error Signal
2 2 2 2 1 1 1 1 ZS Zero Hz Speed
Detection Signal
DSE Speed Deviation
22 22 22 22
Excessive
23 23 POK Positioning Completion ON
23 23
O O O O utput Function Summary Table utput Function Summary Table
utput Function Summary Table utput Function Summary Table
ON When the inverter is in Run Mode
OFF When the inverter is in Stop Mode
ON When output to motor is at the set frequency
OFF When output to motor is OFF, or in any
acceleration or deceleration ramp
ON When output to motor is at or above the set freq,
even if in accel (C C C C 0 0 0 0 42
OFF When output to motor is OFF,
or at a level below the set frequency
ON When output current is more than the set
threshold (C C C C 0 0 0 0 4 4 4 4 1 1 1 1 ) for the overload signal
OFF When output current is less than the set
threshold for the deviation signal
ON When PID error is more than the set threshold
for the deviation signal
OFF When PID error is less than the set threshold for
the deviation signal
ON When an alarm signal has occurred and has not
been cleared
OFF When no alarm has occurred since the last
cleaning of alarm(s)
ON When output to motor is at the set frequency,
during accel (C C C C 0 0 0 0 42
OFF When output to motor is OFF,
or is not at a level of the set frequency
ON Estimated motor torque exceeds
the specified level
OFF Estimated motor torque is lower than
the specified level
ON Inverter is in Undervoltage
OFF Inverter is not in Undervoltage
ON Torque limit function is executing
OFF Torque limit function is not executing
ON Total running time of the inverter exceeds
the specified value
OFF Total running time of the inverter does not
exceed the specified value
ON Total power ON time of the inverter exceeds
the specified value
OFF Total power ON time of the inverter does not
exceed the specified value
ON Accumulated thermal count exceeds
the C C C C 0 0 0 0 6 6 6 6 1 1 1 1 set value
OFF Accumulated thermal count does not exceed the
C C C C 0 0 0 0 6 6 6 6 1 1 1 1 set value
ON Output for brake release
OFF No action for brake
ON Brake error has occurred
OFF Brake performance is normal
ON Output frequency falls below the threshold
specified in C C C C 0 0 0 0 6 6 6 6 3 3 3 3
OFF Output frequency is higher than the threshold
specified in C C C C 0 0 0 0 6 6 6 6 3 3 3 3
ON Deviation of speed command and actual speed
exceeds the specified value P P P P 0 0 0 0 2 2 2 2 7 7 7 7 .
OFF Deviation of speed command and actual speed
does not exceed the specified value P P P P 0 0 0 0 2 2 2 2 7 7 7 7 .
Positioning is completed
OFF Positioning is not completed
D D D D escription escription escription escription
42) or decel (C C C C 0 0 0 0 43 43) ramps
42 42 43 43
42) and decel (C C C C 0 0 0 0 43 42 42 43). 43 43
Ver.3− − − − 145