Hitachi WJ200-001S Instruction Manual page 641

Ver.3− − − − 132
Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
b b b b 0 0 0 0 86 86 Frequency
86 86
scaling
conversion factor
b b b b 0 0 0 0 87 87 STOP key enable
87 87
b b b b 0 0 0 0 88 88 Restart mode
88 88
after FRS
b b b b 0 0 0 0 89 89 89 89 Automatic carrier
frequency
reduction
b b b b 0 0 0 0 9 9 9 9 0 0 0 0 Dynamic braking
usage ratio
b b b b 0 0 0 0 9 9 9 9 1 1 1 1 Stop mode
selection
b b b b 0 0 0 0 9 9 9 9 2 2 2 2 Cooling fan
control
Clear elapsed
b b b b 0 0 0 0 9 9 9 9 3 3 3 3
time of cooling
fan
b b b b 0 0 0 0 9 9 9 9 4 4 4 4 Initialization
target data
b b b b 0 0 0 0 9 9 9 9 5 5 5 5 Dynamic braking
control (BRD)
selection
BRD activation
b b b b 0 0 0 0 96 96 96 96
level
b b b b 0 0 0 0 97 97
97 97
BRD resistor
value
b b b b 1 1 1 1 00 00
00 00
Free V/F setting,
freq.1
b b b b 1 1 1 1 0 0 0 0 1 1 1 1
Free V/F setting,
voltage.1
b b b b 1 1 1 1 0 0 0 0 2 2 2 2
Free V/F setting,
freq.2
b b b b 1 1 1 1 0 0 0 0 3 3 3 3
Free V/F setting,
voltage.2
b b b b 1 1 1 1 0 0 0 0 4 4 4 4
Free V/F setting,
freq.3
b b b b 1 1 1 1 0 0 0 0 5 5 5 5
Free V/F setting,
voltage.3
" " " " b b b b " " " " Function Function
Function Function
D D D D escription
Specify a constant to scale the displayed frequency for d d d d 00
monitor, range is 0.01 to 99.99
Select whether the STOP key on the keypad is enabled, three
option codes:
00 00 00 ... Enabled 00
0 0 0 0 1 1 1 1 ... Disabled always
0 0 0 0 2 2 2 2 ... Disabled for stop
Selects how the inverter resumes operation when free-run stop
(FRS) is cancelled, three options:
00 ... Restart from 0Hz 00 00 00
0 0 0 0 1 1 1 1 ... Restart from frequency detected from real speed of motor
(freq. matching)
0 0 0 0 2 2 2 2 ... Restart from frequency detected from real speed of motor
(active freq. matching)
Three option codes:
00 ... Disabled 00
00 00
0 0 0 0 1 1 1 1 ... Enabled, depending on the output current
0 0 0 0 2 2 2 2 ... Enabled, depending on the heat-sink temperature
Selects the rate of use (in %) of the regenerative braking resistor
per 100 sec. intervals, range is 0.0 to 100%.
0%: Function disabled
>0%: Enabled, per value
Select how the inverter stops the motor, two option codes:
00 00 00 00 ... DEC (decelerate to stop)
0 0 0 0 1 1 1 1 ... FRS (free-run to stop)
Selects when the fan is ON during inverter operation, three
options:
00 00 ... Fan is always ON 00 00
0 0 0 0 1 1 1 1 ... Fan is ON during run, OFF during stop (5 minute delay
from ON to OFF)
0 0 0 0 2 2 2 2 ... Fan is temperature controlled
Two option codes:
00 ... Count 00 00 00
0 0 0 0 1 1 1 1 ... Clear
Select initialized parameters, four option codes:
00 00 00 00 ... All parameters
0 0 0 0 1 1 1 1 ... All parameters except in/output terminals and
communication.
0 0 0 0 2 2 2 2 ... Only registered parameters in U U U U xxx.
0 0 0 0 3 3 3 3 ... All parameters except registered parameters in U U U U xxx and
b b b b 0 0 0 0 3 3 3 3 7 7 7 7 .
Three option codes:
00 00 ... Disable 00 00
0 0 0 0 1 1 1 1 ... Enable during run only
0 0 0 0 2 2 2 2 ... Enable always
Range is:
330 to 380V (200V class)
660 to 760V (400V class)
Min.Resistance to 600.0
Set range, 0 to value of b b b b 1 1 1 1 0 0 0 0 2 2 2 2
Set range, 0 to 800V
Set range, value of b b b b 1 1 1 1 00 00 to b b b b 1 1 1 1 0 0 0 0 4 4 4 4
00 00
Set range, 0 to 800V
Set range, value of b b b b 1 1 1 1 0 0 0 0 2 2 2 2 to b b b b 1 1 1 1 0 0 0 0 6 6 6 6
Set range, 0 to 800V
escription escription escription
D D D D efaults
A A A A B B B B
Initial data Initial data Initial data Initial data
007 7 7 7
00 00
1.00
00
00
01
0.0
00
01
00
00
00
360/
720
Min.
Resistance
0.
0.0
0.
0.0
0.
0.0
efaults
efaults efaults
Units Units Units Units
−
−
−
-
%
−
-
-
-
-
V
Ohm
Hz
V
Hz
V
Hz
V