Hitachi WJ200-001S Instruction Manual page 636

Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
A A A A 1 1 1 1 5 5 5 5 1 1 1 1 Curvature of EL-S-curve at
the end of acceleration
A A A A 1 1 1 1 52 52 52 52 Curvature of EL-S-curve at
the start of deceleration
A A A A 1 1 1 1 53 53 Curvature of EL-S-curve at
53 53
the end of deceleration
A A A A 1 1 1 1 54 54 Deceleration hold frequency
54 54
A A A A 1 1 1 1 55 55 55 55 Deceleration hold time
A A A A 1 1 1 1 5 5 5 5 6 6 6 6 PID sleep function action
threshold
PID sleep function action
A A A A 1 1 1 1 5 5 5 5 7 7 7 7
delay time
A A A A 1 1 1 1 6 6 6 6 1 1 1 1 [VR] input active range
start frequency
[VR] input active range end
A A A A 1 1 1 1 6 6 6 6 2 2 2 2
frequency
A A A A 1 1 1 1 6 6 6 6 3 3 3 3 [VR] input active range
start %
A A A A 1 1 1 1 6 6 6 6 4 4 4 4 [VR] input active range
end %
A A A A 1 1 1 1 6 6 6 6 5 5 5 5 [VR] input start frequency
select
: Available from version 3.0
*2
: Power cycle is required to reflect a change.
*3
" " " " A A A A " " " " Function Function
Function Function
D D D D escription escription escription escription
Range is 0. to 50.%
Range is 0 to 50%
Range is 0. to 50.%
Sets the frequency to hold
deceleration, range is 0.00 to
400.0(580.0) *1 Hz
Sets the duration of deceleration
hold, range is 0.0 to 60.0 seconds
Sets the threshold for the action,
set range 0.00 to 400.0(580.0)
Sets the delay time for the action,
set range 0.0 to 25.5 sec
The output frequency
corresponding to the analog input
range starting point,
range is 0.00 to 400.0(580.0)
The output frequency
corresponding to the current input
range ending point,
range is 0.00 to 400.0(580.0)
The starting point (offset) for the
current input range,
range is 0. to 100.%
The ending point (offset) for the
current input range,
range is 0. to VR end ratio(%)
Two options; select codes:
00 ... Use offset (A A A A 1 1 1 1 6 6 6 6 1 1 1 1 value) 00 00 00
0 0 0 0 1 1 1 1 ... Use 0Hz
A A A A B B B B
*1 Hz
*1 Hz
*1 Hz
Ver.3− − − − 127
D D D D efaults efaults
efaults efaults
Initial data Initial data Initial data Initial data Units Units Units Units
10. %
10. %
10. %
0.00 Hz
0.0 s
0.00 Hz
0.0 s
0.00 Hz
0.00 Hz
0. %
100. %
01
−