Hitachi WJ200-001S Instruction Manual page 647

Ver.3− − − − 138
Func. Func. Func. Func.
Code Code
Code Code
C C C C 1 1 1 1 0 0 0 0 1 1 1 1 Up/Down memory mode
selection
Reset selection
C C C C 1 1 1 1 0 0 0 0 2 2 2 2
C C C C 1 1 1 1 0 0 0 0 3 3 3 3 Restart mode after reset
C C C C 1 1 1 1 0 0 0 0 4 4 4 4 UP/DWN clear mode
C C C C 1 1 1 1 0 0 0 0 5 5 5 5 EO gain adjustment
C C C C 1 1 1 1 0 0 0 0 6 6 6 6 AM gain adjustment
AM bias adjustment
C C C C 1 1 1 1 0 0 0 0 9 9 9 9
C C C C 111 111 Overload warning level 2
111 111
C C C C 1 1 1 1 3 3 3 3 0 0 0 0 Output [11] on delay
C C C C 1 1 1 1 3 3 3 3 1 1 1 1 Output [11] off delay
C C C C 1 1 1 1 32 32 32 32 Output [12] on delay
C C C C 1 1 1 1 33 33 Output [12] off delay
33 33
C C C C 1 1 1 1 4 4 4 4 0 0 0 0 Relay output on delay
C C C C 1 1 1 1 4 4 4 4 1 1 1 1 Relay output off delay
C C C C 1 1 1 1 42 42 42 42 Logic output 1 operand A
Logic output 1 operand B
C C C C 1 1 1 1 43 43 43 43
C C C C 1 1 1 1 44 44 Logic output 1 operator
44 44
C C C C 1 1 1 1 45 45 Logic output 2 operand A
45 45
C C C C 1 1 1 1 4 4 4 4 6 6 6 6 Logic output 2 operand B
C C C C 1 1 1 1 4 4 4 4 7 7 7 7 Logic output 2 operator
C C C C 1 1 1 1 4 4 4 4 8 8 8 8 Logic output 3 operand A
" " " " C C C C " " " " Function Function
Function Function
N N N N ame ame ame ame
Controls speed setpoint for the inverter after power cycle.
Two option codes:
00 ... Clear last frequency (return to default frequency 00
00 00
F F F F 00 00 001 1 1 1 ) 00
0 0 0 0 1 1 1 1 ... Keep last frequency adjusted by UP/DWN
Determines response to Reset input [RS].
Four option codes:
00 00 ... Cancel trip state at input signal ON transition, stops
00 00
inverter if in Run Mode
0 0 0 0 1 1 1 1 ... Cancel trip state at signal OFF transition, stops
inverter if in Run Mode
0 0 0 0 2 2 2 2 ... Cancel trip state at input ON transition, no effect if in
Run Mode
0 0 0 0 3 3 3 3 ... Clear the memories only related to trip status
Determines the restart mode after reset is given, three
option codes:
00 ... Start with 0 Hz 00 00 00
0 0 0 0 1 1 1 1 ... Start with freq. matching
0 0 0 0 2 2 2 2 ... Start with active freq. matching
Freq. set value when UDC signal is given to the input
terminal, two option codes:
00 00 00 00 ... 0 Hz
0 0 0 0 1 1 1 1 ... Original setting (in the EEPROM memory at power
on)
Set range is 50. to 200.%
Set range is 50. to 200.%
Set range is 0. to 100.%
Sets the overload warning signal level between 0% and
200% (from 0 to two time the rated current of the inverter)
Set range is 0.0 to 100.0 sec.
Set range is 0.0 to 100.0 sec.
Set range is 0.0 to 100.0 sec.
All the programmable functions available for logic (discrete)
outputs except LOG1 to LOG3, OPO, no
Applies a logic function to calculate [LOG] output state,
Three options:
00 00 00 00 ... [LOG] = A AND B
0 0 0 0 1 1 1 1 ... [LOG] = A OR B
0 0 0 0 2 2 2 2 ... [LOG] = A XOR B
All the programmable functions available for logic (discrete)
outputs except LOG1 to LOG3, OPO, no
Applies a logic function to calculate [LOG] output state,
Three options:
00 00 ... [LOG] = A AND B
00 00
0 0 0 0 1 1 1 1 ... [LOG] = A OR B
0 0 0 0 2 2 2 2 ... [LOG] = A XOR B
All the programmable functions available for logic (discrete)
outputs except LOG1 to LOG3, OPO, no
D D D D escription escription escription escription
D D D D efaults efaults
efaults efaults
A A A A B B B B
In In In Initial itial itial itial
Units Units Units Units
data data
data data
00
−
00
−
00 -
00 -
100. %
100. %
0. %
Rated
current
A
x 1.15
0.0 s
0.0 s
0.0 s
0.0 s
0.0 s
0.0 s
00
−
00
−
00
−
00
−
00
−
00
−
00
−