Hitachi WJ200-001S Instruction Manual page 631

Ver.3− − − − 122
Func. Func.
Func. Func.
Code Code Code Code
A A A A 0 0 0 0 1 1 1 1 5 5 5 5 [O] input start frequency
enable
A A A A 0 0 0 0 1 1 1 1 6 6 6 6 Analog input filter
EzSQ function select
A A A A 0 0 0 0 1 1 1 1 7 7 7 7
A A A A 0 0 0 0 1 1 1 1 9 9 9 9 Multi-speed operation
selection
Multi-speed freq. 0
A A A A 0 0 0 0 2 2 2 2 0 0 0 0
A A A A 22 220 0 0 0 Multi-speed freq. 0,
22 22
2 nd motor
Multi-speed freq. 1 to 15
A A A A 0 0 0 0 2 2 2 2 1 1 1 1
(for both motors)
to
A A A A 0 0 0 0 35 35 35 35
A A A A 0 0 0 0 3 3 3 3 8 8 8 8 Jog frequency
A A A A 0 0 0 0 3 3 3 3 9 9 9 9 Jog stop mode
A A A A 0 0 0 0 4 4 4 4 1 1 1 1 Torque boost select
A A A A 24 241 1 1 1 Torque boost select, 2
24 24
motor
Manual torque boost value
A A A A 0 0 0 0 42 42 42 42
A A A A 242 242 242 242 Manual torque boost value,
2 nd motor
A A A A 0 0 0 0 43 43 Manual torque boost
43 43
frequency
A A A A 243 243 Manual torque boost
243 243
frequency,
2 nd motor
" " " " A A A A " " " " Function Function
Function Function
N N N N ame ame ame ame
Two options; select codes:
00 00 ... Use offset (A A A A 0 0 0 0 11 00 00
0 0 0 0 1 1 1 1 ... Use 0Hz
Range n = 1 to 31,
1 to 30 :
31: 500ms fixed filter with
0.1kHz hysteresisi.
Select codes:
00 00 00 00 ... Disable
0 0 0 0 1 1 1 1 ... Activate by PRG terminal
0 0 0 0 2 2 2 2 ... Activate always
Select codes:
00...Binary operation (16 speeds 00
00 00
selectable with 4 terminals)
0 0 0 0 1 1 1 1 ...Bit operation (8 speeds
selectable with 7 terminals)
Defines the first speed of a
multi-speed profile, range is 0.00 /
start frequency to 400(580)
A A A A 0 0 0 0 2 2 2 2 0 0 0 0 = Speed 0 (1st motor)
Defines the first speed of a
multi-speed profile or a 2nd motor,
range is 0.00 / start frequency to
400(580)
A A A A 22 220 0 0 0 = Speed 0 (2nd motor)
22 22
Defines 15 more speeds,
range is 0.00 / start frequency to
400(580)
A A A A 0 0 0 0 2 2 2 2 1 1 1 1 =Speed 1 to A A A A 0 0 0 0 35
Defines limited speed for jog,
range is from start frequency to
9.99 Hz
Define how end of jog stops the
motor; six options:
00 00 ... Free-run stop (invalid during
00 00
run)
0 0 0 0 1 1 1 1 ... Controlled deceleration
(invalid during run)
0 0 0 0 2 2 2 2 ... DC braking to stop(invalid
during run)
0 0 0 0 3 3 3 3 ... Free-run stop (valid during
run)
0 0 0 0 4 4 4 4 ... Controlled deceleration (valid
during run)
0 0 0 0 5 5 5 5 ... DC braking to stop(valid
during run)
Two options:
00 00 ... Manual torque boost
00 00
0 0 0 0 1 1 1 1 ... Automatic torque boost
nd
Can boost starting torque between
0 and 20% above normal V/f curve,
range is 0.0 to 20.0%
Sets the frequency of the V/f
breakpoint A in graph (top of
previous page) for torque boost,
range is 0.0 to 50.0%
D D D D escription escription escription escription
11 value) 11 11
2 ms filter
×
±
*1 Hz
*1 Hz
*1 Hz.
35=Speed15
35 35
D D D D efaults efaults
efaults efaults
A A A A B B B B
Initial data Initial data Initial data Initial data
01
8.
00
00
6.0
6.0
0.0
6.00
04
00
00
1.0
1.0
5.0
5.0
Units Units Units Units
−
Spl.
-
-
Hz
Hz
Hz
Hz
−
−
−
%
%
%
%