Hitachi WJ200-001S Instruction Manual page 630

Standard Functions
NOTE E E E :. Parameters marked with " " in A column can set even in inverter running and marked with " " NOT NOT NOT
cannot set in inverter running. Parameters marked with " " in B column can set even in inverter
running and marked with " " cannot set in inverter running when in the high level access mode, which
means that b031 is set to "10". Parameter marked with "− " in A and B column cannot be set, because that
menu is a monitor function.
Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
Frequency source
A A A A 00 001 1 1 1 00 00
Frequency source,
A A A A 2 2 2 2 0 0 0 0 1 1 1 1
2 nd motor
A A A A 00 002 2 2 2 00 00 Run command source
A A A A 2 2 2 2 0 0 0 0 2 2 2 2 Run command source,
2 nd motor
Base frequency
A A A A 00 003 3 3 3 00 00
A A A A 2 2 2 2 0 0 0 0 3 3 3 3 Base frequency,
2 nd motor
A A A A 00 004 4 4 4 00 00 Maximum frequency
A A A A 2 2 2 2 0 0 0 0 4 4 4 4 Maximum frequency,
2 nd motor
[AT] selection
A A A A 00 005 5 5 5 00 00
A A A A 0 0 0 0 11 11 11 11 [O] input active range start
frequency
A A A A 0 0 0 0 1 1 1 1 2 2 2 2 [O] input active range end
frequency
A A A A 0 0 0 0 1 1 1 1 3 3 3 3 [O] input active range start
voltage
A A A A 0 0 0 0 1 1 1 1 4 4 4 4 [O] input active range end
voltage
" " " " A A A A " " " " Function Function
Function Function
D D D D escription escription escription escription
Eight options; select codes:
00 ... POT on ext. operator 00 00 00
*Valid when connecting
OPE-SR/SRmini
0 0 0 0 1 1 1 1 ... Control terminal
*Set to "01" when connecting the
WJ-VL or External volume via
control terminal
0 0 0 0 2 2 2 2 ... Function F001 setting
0 0 0 0 3 3 3 3 ... Modbus network input
0 0 0 0 4 4 4 4 ... Option
0 0 0 0 6 6 6 6 ... Pulse train input
0 0 0 0 7 7 7 7 ... via EzSQ
1 1 1 1 0 0 0 0 ... Calculate function output
Four options; select codes:
0 0 0 0 1 1 1 1 ... Control terminal
0 0 0 0 2 2 2 2 ... Run key on keypad, or digital
operator
0 0 0 0 3 3 3 3 ... Modbus network input
0 0 0 0 4 4 4 4 ... Option
Settable from 30 Hz to the
maximum frequency(A A A A 00
Settable from 30 Hz to the 2
maximum frequency(A A A A 2 2 2 2 0 0 0 0 4 4 4 4 )
Settable from the base
frequency to 400(580)
Settable from the 2
frequency to 400(580)
Three options; select codes:
00...Select between [O] and [OI] at 00 00 00
[AT] (ON=OI, OFF=O)
0 0 0 0 2 2 2 2 ...Select between [O] and
external POT at [AT]
(ON=POT, OFF=O)
0 0 0 0 3 3 3 3 ...Select between [OI] and
external POT at [AT]
(ON=POT, OFF=OI)
The output frequency
corresponding to the analog input
range starting point,
range is 0.00 to 400.0(580.0)
The output frequency
corresponding to the analog input
range ending point,
range is 0.00 to 400.0(580.0)
The starting point (offset) for the
active analog input range,
range is 0. to 100.
The ending point (offset) for the
active analog input range,
range is 0. to 100.
A A A A
the
00 004 4 4 4 ) 00
nd
*1 Hz
nd base
*1 Hz
*1
*1
Ver.3− − − − 121
D D D D efaults efaults
efaults efaults
B B B B
Initial data Initial data Initial data Initial data
01
01
01
01
50.0
50.0
50.0
50.0
00
0.00
0.00
0.
100.
Units Units Units Units
−
−
−
−
Hz
Hz
Hz
Hz
−
Hz
Hz
%
%