Hitachi WJ200-001S Instruction Manual page 32

Item
Output Intelligent output
signal terminal
48 functions assignable
Monitor output (analog)
Pulse train output
(0~10Vdc, 32kHz max.)
Alarm output contact
Other functions
Protective function
Operating Temperature
environment
Humidity
Vibration *11
Location
Coating color
Options
General Specifications
RUN RUN (run signal), FA1~FA5 RUN RUN FA1~FA5 FA1~FA5 FA1~FA5 (frequency arrival signal), OL,OL2
advance notice signal), OD OD (PID deviation error signal), AL OD OD
OTQ OTQ (over/under torque threshold), UV
OTQ OTQ
signal), RNT RNT (run time expired), ONT RNT RNT
(thermal warning), BRK BRK BRK (brake release), BER BRK
detection), DSE DSE (speed deviation excessive), POK DSE DSE
ODc ODc (analog voltage input disconnection), OIDc
ODc ODc
disconnection), FBV FBV FBV FBV (PID second stage output), NDc
detection), LOG1~LOG3 LOG1~LOG3 (Logic output signals), WAC LOG1~LOG3 LOG1~LOG3
warning), WAF WAF (cooling fan warning), FR
WAF WAF
overheat warning), LOC LOC LOC (Low load), MO1~MO3 LOC
IRDY IRDY IRDY (inverter ready), FWR IRDY FWR FWR (forward operation), RVR FWR
MJA MJA MJA (major failure), WCO MJA WCO WCO (window comparator O), WCOI WCO
comparator OI), FREF FREF (frequency command source), REF
FREF FREF
source), SETM SETM (second motor in operation), EDM SETM SETM
performance monitor), OP OP OP (option control signal), NO OP
Output freq., output current, output torque, output voltage, input power,
thermal load ratio, LAD freq., heat sink temperature, general output (EzSQ)
[PWM output] [PWM output] [PWM output] [PWM output]
Output freq., output current, output torque, output voltage, input power,
thermal load ratio, LAD freq., heat sink temperature, general output (EzSQ)
[Pulse train output] [Pulse train output] [Pulse train output] [Pulse train output]
Output frequency, output current, pulse train input monitor
ON for inverter alarm (1c contacts, both normally open or closed available.)
Free-V/f, manual/automatic torque boost, output voltage gain adjustment,
AVR function, reduced voltage start, motor data selection, auto-tuning,
motor stabilization control, reverse running protection, simple position
control, simple torque control, torque limiting, automatic carrier frequency
reduction, energy saving operation, PID function, non-stop operation at
instantaneous power failure, brake control, DC injection braking, dynamic
braking (BRD), frequency upper and lower limiters, jump frequencies, curve
accel and decel (S, U, inversed U,EL-S), 16-stage speed profile, fine
adjustment of start frequency, accel and decel stop, process jogging,
frequency calculation, frequency addition, 2-stage accel/decel, stop mode
selection, start/end freq., analog input filter, window comparators, input
terminal response time, output signal delay/hold function, rotation direction
restriction, stop key selection, software lock, safe stop function, scaling
function, display restriction,
initialization, initial display selection, cooling fan control, warning, trip
retry, frequency pull-in restart, frequency matching, overload restriction,
over current restriction, DC bus voltage AVR
Over-current, over-voltage, under-voltage, overload, brake resistor overload,
CPU error, memory error, external trip, USP error, ground fault detection at
power on, temperature error, internal communication error, driver error,
thermistor error, brake error, safe stop, overload at low speed, modbus
communication error, option error, encoder disconnection, speed excessive,
EzSQ command error, EzSQ nesting error, EzSQ execution error, EzSQ user
trip
Operating (ambient): -10 to 40°C(*10), / Storage: -20 to 65°C(*11)
20 to 90% humidity (non-condensing)
5.9m/s (0.6G), 10 to 55 Hz
2
Altitude 1,000m or less, indoors (no corrosive gasses or dust)
Black
Remote operator unit, cables for the units, braking unit, braking resistor, AC
reactor, DC reactor, EMC filter, fieldbus
OL,OL2 (overload OL,OL2 OL,OL2
AL AL (alarm signal), AL
UV (under-voltage), TRQ TRQ (torque limit
UV UV TRQ TRQ
ONT ONT (power ON time expired), THM ONT
BER BER (brake error), ZS BER
POK (positioning completion), POK POK
OIDc (analog current input
OIDc OIDc
NDc NDc (network disconnect NDc
WAC WAC (capacitor life WAC
FR (starting contact), OHF OHF (heat sink
FR FR OHF OHF
MO1~MO3 MO1~MO3 MO1~MO3 (general outputs for EzSQ),
RVR (reverse operation), RVR RVR
WCOI (window WCOI WCOI
REF (run command
REF REF
EDM EDM (STO (safe torque off) EDM
NO NO NO (no function)
password function, user
1− − − − 9
THM THM THM
ZS (0Hz ZS ZS
parameter,