Pontiac Fiero 1988 Service Manual page 1325

5J-14
DOORS
DOOR GLASS ASSEMBLY
1.
2.
3.
4.
5.
6.
7.
8.
2.
3.
4.
Remove or Disconnect (Figure 22)
Door trim panel
Water deflector
Front filler sealing strip
Rear filler sealing strip
Rivets (86)
@ Cam assembly
• Front stop (80)
• Rear stop (81)
Front and rear stops
Loosen door glass stabilizers
Remove all bushings from glass before removing
glass
Glass (77)
Install or Connect (Figure 22)
Install all bushings in glass before installing glass
in door.
Glass to cam assembly (78)
Front and rear stops
Rivets (86)
• Front stop (80)
• Rear stop (81)
© Cam assembly
j|tF| Inspect
Window for proper operation
Adjust
I2LJ
5.
6.
7.
8.
As required
Rear filler sealing strip
Front filler sealing strip
Water deflector
Door trim panel
Inspect
Glass for applicable condition. Refer to
applicable condition to determine the components that
will require adjustment. Make adjustments only as
required for correct alignment and operation. The door
trim panel and water deflector must be removed for
access to components.
ft
Adjust (Figure 23)
Window rotated
• Loosen up-stop bolts (97 and 93)
© Adjust inner panel cam-bolts (98 and 99)
• Adjust window so that upper edge of glass is
parallel with roof side rail weatherstrip.
m Adjust up-stops
• Tighten attaching bolts
Window upper edge inboard or outboard
• Loosen rear up-stop (93)
• Loosen front and rear glass stabilizer screws (95
and 96)
• Adjust vertical guide and rear up-stop support in
or out as required and tighten attaching screws
Window too far forward or rearward
• Loosen front run channel bolts (88 and 89)
m Loosen rear cam guide assembly (90 and 91)
m Align glass in correct up position
• Tighten upper bolt on front run channel (88)
• Tighten upper bolts on rear cam guide (91)
e Lower glass
m Tighten lower bolt on front run channel (89)
• Tighten lower bolts on rear cam guide (90)
Window too high or low in up position
• Adjust front and rear up-stop bolts (93 and 97)
as required and tighten bolts.
Window binds or has inboard-outboard movement
• Loosen glass stabilizers (95 and 96)
$ Place glass in half-up position
• Push stabilizers against glass with only enough
pressure to eliminate inboard-outboard
movement.
• Tighten glass stabilizers (95 and 96)
• If cam channels and rollers lack lubrication,
lubricate with part no. 1052196, Lubriplate
Auto-Lube A (or equivalent).
Inspect
After making any adjustment, inspect glass for
proper operation and alignment.
El
Tighten
All loosened attachments from 10 to 14 N-m (90
to 125 in-lb)
Window Regulator Cam Assembly
Remove or Disconnect (Figures 22,23)
Door trim panel
Water deflector
Lower glass halfway and block in place.
Rivets from cam assembly (78)
Separate glass from cam assembly (78)
Raise glass to full-up position and block in place.
Window guide cam assembly bolts (90 and 91)
Plate (103, Fig. 28)
Rivets - regulator to inner door (9, Fig. 28)
Regulator cam assembly (78)
|+«-| Install or Connect (Figures 22,23)
Regulator cam assembly (78)
Rivets - regulator to inner door (9, Fig. 28)
Plate (103, Fig. 28)
Window guide cam assembly bolts (90 and 91)
Remove blocks and lower glass
Glass to cam assembly (78)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.