Endress+Hauser Prosonic Flow I 400 Manuals

Endress+Hauser Prosonic Flow I 400 Manuals

Manuals and User Guides for Endress+Hauser Prosonic Flow I 400. We have 2 Endress+Hauser Prosonic Flow I 400 manuals available for free PDF download: Operating Instructions Manual, Installation Instructions Manual

Endress+Hauser Prosonic Flow I 400 Operating Instructions Manual

Endress+Hauser Prosonic Flow I 400 Operating Instructions Manual (176 pages)

Ultrasonic time-of-flight flowmeter Modbus RS485

Brand: Endress+Hauser | Category: Measuring Instruments | Size: 5 MB

Table of Contents

Table of Contents

3
- Electrical Symbols
  6
- Communication-Specific Symbols
  6
- About this Document
  6
- Safety Symbols
  6
- Symbols
  6
- Document Function
  6
- Tool Symbols
  7
- Symbols in Graphics
  7
- Symbols for Certain Types of Information
  7
- Documentation
  8
- Registered Trademarks
  8
- Safety Instructions
  9
- Requirements for the Personnel
  9
- Intended Use
  9
- Security
  10
- Device-Specific IT Security
  10
- Operational Safety
  10
- Product Safety
  10
- Workplace Safety
  10
- Protecting Access Via Hardware Write Protection
  11
- Protecting Access Via a Password
  11
- Access Via Web Server
  12
- Access Via Service Interface (CDI-RJ45)
  12
- Product Description
  13
- Product Design
  14
- Identification
  15
- Incoming Acceptance
  15
- Product Identification
  15
- Transmitter Nameplate
  16
- Sensor Nameplate
  16
- Symbols on the Device
  17
- Packaging Disposal
  18
- Transporting with a Fork Lift
  18
- Transporting the Product
  18
- Storage Conditions
  18
- Storage and Transport
  18
- Mounting Procedure
  19
- Mounting Requirements
  19
- Mounting Position
  19
- Sensor Set Selection and Arrangement
  22
- Environmental and Process Requirements
  23
- Required Tools
  24
- Mounting the Measuring Device
  24
- Special Mounting Instructions
  24
- Preparing the Measuring Device
  25
- Mounting the Sensor
  25
- Mounting the Transmitter
  30
- Turning the Display Module
  32
- Post-Mounting Check
  32
- Requirements for Connecting Cable
  34
- Required Tools
  34
- Connecting Requirements
  34
- Electrical Safety
  34
- Electrical Connection
  34
- Terminal Assignment
  35
- Shielding and Grounding
  36
- Preparing the Measuring Device
  36
- Connecting the Measuring Device
  37
- Connecting the Sensor with Transmitter
  37
- Connecting the Transmitter
  39
- Potential Equalization
  39
- Ensuring the Degree of Protection
  40
- Degree of Protection IP66/67, Type 4X Enclosure
  40
- Special Connection Instructions
  40
- Activating the Terminating Resistor
  40
- Hardware Settings
  40
- Connection Examples
  40
- Post-Connection Check
  41
- Operation Options
  42
- Overview of Operation Methods
  42
- Structure and Function of the Operating Menu
  43
- Structure of the Operating Menu
  43
- Operating Philosophy
  44
- Access to Operating Menu Via Local Display
  45
- Operational Display
  45
- Navigation View
  47
- Editing View
  48
- Operating Elements
  50
- Opening the Context Menu
  51
- Navigating and Selecting from List
  52
- Calling the Parameter Directly
  52
- Calling up Help Text
  53
- Changing the Parameters
  54
- User Roles and Related Access Authorization
  55
- Disabling Write Protection Via Access
  55
- Code
  55
- Function Range
  56
- Access to Operating Menu Via Web Browser
  56
- Enabling and Disabling the Keypad
  56
- Requirements
  57
- Connecting the Device
  58
- Logging on
  60
- User Interface
  61
- Disabling the Web Server
  62
- Logging out
  62
- Access to the Operating Menu Via the Operating Tool
  62
- Connecting the Operating Tool
  63
- Fieldcare
  65
- Devicecare
  66
- Field Xpert SMT70, SMT77
  66
- System Integration
  68
- Overview of Device Description Files
  68
- Current Version Data for the Device
  68
- Operating Tools
  68
- Compatibility with Previous Model
  68
- Function Codes
  69
- Modbus RS485 Information
  69
- Response Time
  70
- Data Types
  70
- Register Information
  70
- Byte Transmission Sequence
  71
- Modbus Data Map
  71
- Commissioning
  74
- Post-Mounting and Post-Connection Check
  74
- Switching on the Measuring Device
  74
- Setting the Operating Language
  74
- Configuring the Measuring Device
  74
Commissioning

76
- Communication
  76
- Setting the System Units
  81
- Baudrate (7111)
  82
- Bus Address (7112)
  82
- Byte Order (7113)
  82
- Configuring the Communication
  82
- Data Transfer Mode (7115)
  82
- Failure Mode (7116)
  82
- Interface
  82
- Parity (7122)
  82
- Configuring the Measuring Point
  83
- Measuring Point
  83
- Measuring Point Configuration (5675)
  85
- Medium (2926)
  85
- Medium Temperature (3053)
  85
- Pipe Circumference (2934)
  85
- Pipe Dimensions (2943)
  85
- Pipe Material (2927)
  85
- Pipe Sound Velocity (2933)
  85
- Sound Velocity (2929)
  85
- Viscosity (2932)
  85
- Cable Length (2939)
  86
- Liner Material (2928)
  86
- Liner Sound Velocity (2936)
  86
- Liner Thickness (2935)
  86
- Mounting Type (2938)
  86
- Pipe Outer Diameter (2910)
  86
- Pipe Wall Thickness (2916)
  86
- Sensor Coupling (2957)
  86
- Sensor Type (2924)
  86
- Inlet Diameter (3054)
  87
- Inlet Run (3050)
  87
- Intermediate Pipe Length (2945)
  87
- Relative Sensor Position (2985)
  87
- Result Path Length / Arc Length (3067)
  87
- Result Sensor Distance / Measuring Aid
  87
- Result Sensor Type / Mounting Type
  87
- Result Sensor Type / Sensor Distance
  87
- Transition Length (3065)
  87
- Checking the Installation Status
  88
- Installation Status
  88
- Installation Status (2958)
  88
- Signal Strength (2914)
  88
- Signal to Noise Ratio (2917)
  88
- Sound Velocity (2915)
  88
- Sound Velocity Deviation (2986)
  88
- Configuring the Current Output
  89
- Current Output 1
  89
- Current Range Output (0353-1)
  89
- Process Variable Current Output
  89
- Fixed Current (0365-1)
  90
- Lower Range Value Output (0367-1)
  90
- Switch Output
  90
- Upper Range Value Output (0372-1)
  90
Endress+Hauser

91
- Assign Pulse Output (0460)
  92
- Operating Mode (0469)
  92
- Assign Frequency Output (0478)
  93
- Assign Diagnostic Behavior (0482)
  94
- Assign Limit (0483)
  94
- Switch Output Function (0481)
  94
- Assign Flow Direction Check (0484)
  95
- Assign Status (0485)
  95
- Failure Mode (0480)
  95
- Switch-Off Delay (0465)
  95
- Switch-Off Value (0464)
  95
- Switch-On Delay (0467)
  95
- Switch-On Value (0466)
  95
- Configuring the Relay Output
  96
- Failure Mode (0486)
  96
- Configuring the Double Pulse Output
  98
- Configuring the Local Display
  99
- Invert Output Signal
  99
- 10.4.10 Configuring the Low Flow Cut off
  101
- Advanced Settings
  103
- Access Code
  104
- Carrying out a Sensor Adjustment
  104
- Configuring the Totalizer
  104
- Carrying out Additional Display Configurations
  106
- WLAN Configuration
  108
- Performing Heartbeat Basic Setup
  110
- Using Parameters for Device Administration
  111
- Simulation
  112
- Protecting Settings from Unauthorized Access
  114
- Write Protection Via Access Code
  114
- Switch
  116
- Adjusting the Operating Language
  117
- Configuring the Display
  117
- Operation
  117
- Reading off Measured Values
  117
- Reading off the Device Locking Status
  117
- Process Variables
  118
- Input Values
  119
- System Values
  119
- Output Values
  120
- Adapting the Measuring Device to the Process
  121
- Conditions
  121
- Totalizer" Submenu
  121
- Function Scope of "Control Totalizer" Parameter
  122
- Performing a Totalizer Reset
  122
- Displaying the Measured Value History
  123
- Function Range of "Reset All Totalizers" Parameter
  123
- Diagnosis and Troubleshooting
  126
- General Troubleshooting
  126
- Diodes
  127
- Transmitter
  127
- Diagnostic Information on Local Display
  129
- Diagnostic Message
  129
- Calling up Remedial Measures
  131
- Diagnostic Information in the Web Browser
  131
- Diagnostic Options
  131
- Calling up Remedy Information
  132
- Diagnostic Options
  132
- Calling up Remedy Information
  133
- Adapting the Diagnostic Behavior
  134
- Adapting the Diagnostic Information
  134
- Configuring Error Response Mode
  134
- Interface
  134
- Reading out Diagnostic Information
  134
- Overview of Diagnostic Information
  135
- Pending Diagnostic Events
  138
- 12.10 Diagnostics List
  139
- 12.11 Event Logbook
  139
- 12.11.1 Reading out the Event Logbook
  139
- 12.11.2 Filtering the Event Logbook
  140
- 12.11.3 Overview of Information Events
  140
- 12.12 Resetting the Measuring Device
  141
- 12.12.1 Function Range of "Device Reset" Parameter
  142
- 12.13 Device Information
  142
- 12.14 Firmware History
  144
- Endress+Hauser Services
  145
- Exterior Cleaning
  145
- Maintenance
  145
- Maintenance Tasks
  145
- Measuring and Test Equipment
  145
- Endress+Hauser Services
  146
- General Notes
  146
- Notes for Repair and Conversion
  146
- Repair
  146
- Repair and Conversion Concept
  146
- Return
  146
- Spare Parts
  146
- Disposal
  147
- Disposing of the Measuring Device
  147
- Removing the Measuring Device
  147
- Accessories
  148
- Device-Specific Accessories
  148
- For the Sensor
  148
- For the Transmitter
  148
- Communication-Specific Accessories
  149
- Service-Specific Accessories
  150
- System Components
  150
- Application
  151
- Function and System Design
  151
- Input
  151
- Technical Data
  151
- Output
  152
- Power Supply
  155
- Performance Characteristics
  157
- Mounting
  159
- Environment
  160
- 16.10 Mechanical Construction
  161
- Process
  161
- 16.11 Display and User Interface
  163
- 16.12 Certificates and Approvals
  166
- 16.13 Application Packages
  167
- 16.14 Accessories
  168
- 16.15 Supplemental Documentation
  168
- Index
  170

Advertisement

Endress+Hauser Prosonic Flow I 400 Installation Instructions Manual

Endress+Hauser Prosonic Flow I 400 Installation Instructions Manual (64 pages)

Brand: Endress+Hauser | Category: Measuring Instruments | Size: 1 MB

Advertisement

Related Products

Endress+Hauser Categories

Measuring Instruments Transmitter Radar

Switch

Switch Accessories

More Endress+Hauser Manuals