Ametek 5920 UHP Manuals

Ametek 5920 UHP Manuals

Manuals and User Guides for Ametek 5920 UHP. We have 1 Ametek 5920 UHP manual available for free PDF download: User Manual

Ametek 5920 UHP User Manual

Ametek 5920 UHP User Manual (117 pages)

Moisture Analyzer for Ultra-High Purity Gases

Brand: Ametek | Category: Measuring Instruments | Size: 4 MB

Table of Contents

Table of Contents
3
Safety Notes
7
Electrical Safety
8
Grounding
8
Sample Gas
8
Personnel and Equipment Safety Information
9
Special Warnings and Information
11
- Equipment Used in Class I, Division 2 Hazardous Locations
  11
- Gas Compatibility Warning
  12
Warning Labels
14
Environmental Information - WEEE
14
Overview

15
- Controller/Communications
  16
- Contact Closure Signals
  17
  - System Alarm
    17
  - Moisture Concentration Alarm
    17
  - Data Valid
    17
- Moisture Sensor
  18
  - Quartz Crystal Microbalance (QCM)
    18
  - Gas Measurement Cycle
    18
- Gas Flow
  19
  - Sample System
    19
  - Solenoid Valves
    21
  - Zeroing the Analyzer
    21
  - Verification with External Challenges
    22
  - Zero Cycle
    23
Installation and Start-Up

25
- Safety Considerations
  25
- Pre-Installation Requirements
  26
  - Personnel Technical Level Required for Installation
    26
- Analyzer Requirements
  27
- Utility Requirements
  30
  - Instrument Air Supply
    30
  - Sample Temperature and Pressure Requirements
    30
- Analyzer Installation
  31
  - User-Supplied Items
    32
    
    Interconnect Wiring
    32
    
    External Sample Tubing
    32
  - Rear Panel Connections and User Interface Board
    33
  - Gas Connections
    34
  - Electrical Connections
    35
    
    Voltage Selection
    35
    
    Power Installation
    36
    
    Communication Connections
    38
    
    Class I, Division 2 Electrical Connections (Alternative) - Hardwire
    39
    
    RS-485 Communications
    40
    
    Signal Connections (4-20 Ma)
    41
- Analyzer Setup
  42
  - Overview of the Keypad
    42
    
    Function Keys
    42
    
    Overview of Display
    44
- Initial Start-Up
  45
- Configuring the 5920 Analyzer for Serial Communications
  48
  - Protocol
    48
  - Special Addresses
    50
    
    Address $F0
    50
  - Defined Commands (Master to Slave)
    50
    
    Echo (A)
    50
    
    Bad Command (B)
    51
    
    Acknowledge (C)
    51
    
    Read Data (F)
    51
    
    Write Data (H)
    51
    
    Write Cell EEPROM (L)
    52
    
    Quit (Q)
    52
    
    Zero (Z)
    52
  - Defined Responses (Slave to Master)
    52
    
    Simple Acknowledge
    52
    
    Acknowledge with Data
    53
    
    Failure
    53
- Variables Table
  54
Controller/Interface

57
- Working from the Built-In User Interface
  57
  - Zero Key
    59
  - Alarm Key
    60
  - Range Key
    61
  - Config Key
    62
    
    Display
    62
    
    Communication
    63
    
    Sample Gas
    64
    
    Clock
    65
    
    Zero Schedule
    66
    
    System Test
    67
- Working from the 5920 UHP Configurator Software
  68
  - Configurator Software Installation
    68
  - Configuring the 5920
    69
    
    Working from the General Tab
    69
    
    Saving Analyzer Configuration Settings
    71
    
    Working from the Device Communication Tab
    72
    
    Configuring Multiple Analyzers
    72
    
    Changing Communication Parameters
    72
    
    Saving Your Settings
    73
    
    Working from the Setup Tab
    74
    
    Working from the Schedule Tab
    76
    
    Saving Your Settings
    77
    
    Working from the Status Tab
    78
    
    Working from the Monitor Tab
    78
    
    Data Capture
    79
Maintenance and Troubleshooting

81
- Aftermarket Excellence and Long-Term Commitment to Safety and Quality
  82
- 5920 UHP Analyzer Replacement Parts
  83
- Servicing the 5920 Analyzer
  84
  - Mass Flow Meter
    85
  - Solenoid Valves
    88
  - Pressure Regulator
    90
  - Diaphragm Valve
    92
  - Installing the Purifiers
    94
- Maintenance of the Electronics Module
  96
- Board Connections
  104
  - Analog Interface Board
    104
  - User Interface Board
    105
  - MCU Board
    106
  - Stepper Motor Board
    107
- Alarm Messages
  108
Specifications

111
Appendix A - Quick Reference Card

115

Advertisement

Advertisement

Related Products

Ametek Categories

Measuring Instruments Test Equipment

Power Supply

Switch

Switch Controller

More Ametek Manuals