Ametek 5800 Manuals

Ametek 5800 Manuals

Manuals and User Guides for Ametek 5800. We have 1 Ametek 5800 manual available for free PDF download: User Manual

Ametek 5800 User Manual

Ametek 5800 User Manual (104 pages)

Moisture

Brand: Ametek | Category: Measuring Instruments | Size: 1.93 MB

Table of Contents

Table of Contents
3
Sample Gas
6
Safety Notes
6
Electrical Safety
6
Grounding
6
Warning Labels
7
Electromagnetic Compatibility (EMC)
8
Special Warnings and Information
9
Dryer Warning
9
Chapter 1 5830 MOISTURE ANALYZER

10
- Overview
  13
  - Controller / Communications
    14
  - Contact Closure Signals
    14
  - Moisture Sensor
    15
    
    Quartz Crystal Microbalance (QCM)
    15
    
    Gas Measurement Cycle
    15
  - Gas Flow
    15
    
    Sample System
    15
    
    Sample Flow
    16
    
    Solenoid Valves
    17
    
    Zero Gas Module
    18
  - Zeroing the Analyzer
    18
  - Verifying the Analyzer
    19
  - Dew/Frost Point Measurements
    19
Chapter 2 SPECIFICATIONS

21
Chapter 3 Installation and Start-Up

25
- Analyzer Requirements
  26
  - Space Requirements
    26
  - Utility Requirements
    28
    
    Electrical Requirements
    28
    
    Instrument Air Supply
    28
  - Sample Temperature and Pressure Requirements
    28
- Analyzer Installation
  29
  - User-Supplied Items
    29
  - Rear Panel Connections and Interface Board
    30
    
    Installing the Dryers (Figures 3-4A and B)
    32
    
    Gas Connections (Figure 3-5)
    34
    
    Electrical Connections (Figure 3-6)
    35
    
    Voltage Selection
    35
    
    Power Connection
    36
    
    Communication Connections (Figure 3-9)
    37
    
    RS-485 Communications
    38
  - Signal Connections (4 to 20 Ma )
    39
    
    Overview of Keypad
    40
    
    Function Keys
    40
    
    Overview of Display
    41
  - Initial Start-Up
    42
    
    Dry-Down Period
    42
    
    Procedure for Speeding up the Dry down Period
    43
  - Performing an Initial Zero
    43
Chapter 4 User Interface

45
- Zero Key
  47
  - Hold Outputs
    47
  - Adjust Offset/Span
    47
  - Zero
    47
  - Verify
    48
  - Abort
    48
- Alarm Key
  48
- Range Key
  49
- Config Key
  50
  - Display
    50
  - Communication
    51
  - Sample Gas
    52
    
    Custom Gas
    52
  - Clock
    53
  - Zero Schedule
    54
  - Verify Schedule
    55
- System Test
  57
Chapter 5 Serial Communications

59
- Protocol
  59
  - Special Addresses
    61
    
    Address $F0
    61
  - Defined Commands (Master to Slave)
    61
    
    Echo (A)
    62
    
    Bad Command (B)
    62
    
    Acknowledge (C )
    62
    
    Read Data (F)
    62
    
    Write Data (H)
    63
    
    Write Cell EEPROM (L)
    63
    
    Quit (Q)
    63
    
    Zero (Z)
    63
  - Defined Responses (Slave to Master)
    64
    
    Simple Acknowledge
    64
    
    Acknowledge with Data
    64
    
    Failure
    64
Chapter 6 Troubleshooting

69
- Alarms
  69
Chapter 7 Service and Parts

71
- Parts Replacement
  71
  - Sensor
    73
  - Removing the Sensor
    73
    
    Installing the Sensor
    73
  - Mass Flow Meter
    74
    
    Removing the Mass Flow Meter
    74
    
    Installing the Mass Flow Meter
    74
  - Moisture Generator
    76
    
    Removing the Moisture Generator
    76
    
    Installing the New Moisture Generator
    77
  - Solenoid Valves
    78
    
    Removing the Solenoids
    78
    
    Installing the New Solenoid
    79
  - Dryers
    80
    
    Removing the Dryers
    80
    
    Installing the New Dryer
    81
- Maintenance of the Electronic Module
  82
- Board Connections
  88
  - User Interface Board
    88
- Spare Parts
  89
Appendix A PC Interface

91
- AMETEK UHP Moisture Configurator Software
  91
  - Configurator Software Installation
    91
  - Configuring the 5830
    92

Advertisement

Advertisement

Related Products

Ametek Categories

Measuring Instruments Test Equipment

Power Supply

Power Supply Controller Laboratory Equipment

More Ametek Manuals