Board; Cp-378 Board - Sony SRW-5000 Maintenance Manual

1-25-7. CP-378 Board

After replacing and repairing this board, perform the
following checks.
Tools
. Audio analyzer:
Audio Precision System One or System Two or equiva-
lent
Checks
1. In the AUDIO menu, perform the following to set all
the audio inputs to AES/EBU. (Refer to the Operation
Manual.)
AUDIO → [F1] (AUDIO IN) → [F7] (AUDIO IN
ALL): AES/EBU
m
. Confirm that the input displays on the top of the
audio meter are turned into A/E.
. Before this menu operation, write down the custom-
er settings to the following table:
Channel Customer
Setting
[||] [||]
CH1 SDI AES/EBU
[||] [||]
CH2 SDI AES/EBU
[||] [||]
CH3 SDI AES/EBU
[||] [||]
CH4 SDI AES/EBU
[||] [||]
CH5 SDI AES/EBU
[||] [||]
CH6 SDI AES/EBU
2. Connect the DIGITAL I/O (AES/EBU) INPUT CH1/2
connector with the AES/EBU output connector of the
audio analyzer.
Also, connect the DIGITAL I/O (AES/EBU) OUT-
PUT CH1/2 connector with the ABS/EBU input
connector of the audio analyzer.
3. Input the _20 dBFs/1 kHz signal from the audio
analyzer, and check that the audio level meters for
CH1 and CH2 indicate _20 dB on the color display
(LCD).
4. Confirm that the level of the AES/EBU input connec-
tor of the audio analyzer is _20 dBFs for both the CH1
and CH2.
5. Perform the same checks for the DIGITAL I/O (AES/
EBU) INPUT/OUTPUT CH3/4 to CH11/12 connec-
tors.
6. Return the settings of the AUDIO menu, which were
changed for the checks, to the customer settings.
1-54
Channel Customer
Setting
[||] [||]
CH7 SDI AES/EBU
[||] [||]
CH8 SDI AES/EBU
[||] [||]
CH9 SDI AES/EBU
[||] [||]
CH10 SDI AES/EBU
[||] [||]
CH11 SDI AES/EBU
[||] [||]
CH12 SDI AES/EBU
1-25-8. CP-382 Board
After repairing this board
(except for NV-RAM replacement)
1. Check that the lower control panel functions normally.
2. Check that the video output signal is correctly dis-
played on the color display (LCD) of the lower control
panel, using the following procedure:
(1) Play back a video tape.
(2) Press the DISPLAY key on the lower control
panel to check that the images being played back
are displayed on the color display.
(3) If necessary, adjust the RGB gain of the color
display. (Refer to Section 3-3-9.)
After replacing the NV-RAM
1. Turn on the power of the unit while pressing the [0],
[SET], and [CLR] keys simultaneously.
n
Keep pressing the keys until the confirmation sound is
beeped. This operation initializes the NV-RAM
without a system error caused by its data loss. (The
setting is reset to the value fixed in the ROM).
2. Adjust the RGB gain of the color display.
(Refer to Section 3-3-9.)
3. Set the POWER ON BANK RECALL setting data
again. (Refer to the operation manual.)
Board Replacement
Before replacing this board, perform the following.
1. If possible, take notes of the following setting data:
. POWER ON BANK RECALL setting data
2. Confirm that each DIP switch on the new board is the
factory setting. (Refer to Section 1-14.)
5. Remove the backup battery from IC226 on the new
board, and install it again after a while.
(Refer to Section 1-17.)
After the board replacement, perform the procedure of
"After replacing the NV-RAM" above.
1-25-9. CUE-13 Board
After replacing and repairing this board, adjust the CUE
playback system (Section 8-5-4).
SRW-5000/5500