Skoda Octavia Workshop Manual page 65

OCTAVIA
2 - Inlet camshaft
♦ runout: max. 0.03…0.05 mm
♦ inspecting axial play ⇒ page 15-15
♦ removing and installing camshaft
⇒ page 15-16
3 - Drive chain
♦ inspecting for wear
♦ mark running direction (installed po-
sition) before removing
⇒ page15-16
4 - Camshaft adjuster
♦ must be located on dowel sleeves
♦ seal the joints between the camshaft
adjuster/cylinder head ⇒ Fig. 2
♦ removing and installing
⇒ page 15-16
♦ inspecting with camshaft adjuster
valve -N205-
⇒ Repair Group 28 of corresponding
Engine, Fuel injection and Ignition sys-
tem; Motronic
5 - Rubber metal gasket
♦ replacing ⇒ page 15-16
6 - Cylinder head
♦ seal joints ⇒ Fig. 1 and Fig. 2
♦ removing ⇒ page 15-6
♦ check for distortion ⇒ page 15-8
♦ reworking ⇒ page 15-8
♦ installing ⇒ page 15-9
♦ inspecting valve guides, grinding in
valve seats ⇒ page 15-31
7 - Outlet valve
♦ with sodium filling
♦ pay attention to regulation for scrap-
ping the valves with sodium filling
⇒ page 15-27
♦ do not rework, only grinding in is per-
missible
♦ valve dimensions ⇒ page 15-27
♦ inspecting valve guides, grinding in
valve seats ⇒ page 15-31
8 - Inlet valve
♦ do not rework, only grinding in is per-
missible
♦ valve dimensions ⇒ page 15-27
♦ inspecting valve guides, grinding in
valve seats ⇒ page 15-31
9 - Seal
♦ for inlet camshaft
♦ replacing ⇒ page 15-21
♦ pay attention to different versions
⇒ page 13-11, Fig. 2
Edition 04.03
S00.5104.56.20
Cylinder Head, Valve Gear
10 - Cover for hall sender
♦ assembly is only possible in one posi-
♦ pay attention to installation position:
11 - Washer
♦ pay attention to installation position:
♦ with cone
12 - 25 Nm
13 - Housing for hall sender (G40)
14 - 10 Nm
15 - 65 Nm
♦ use counterholder MP 1-216 for slack-
16 - Camshaft sprocket
♦ for inlet camshaft
♦ pay attention to installation position:
♦ the small stay on the camshaft
17 - Seal
♦ for outlet camshaft
♦ replacing ⇒ page 15-21
♦ pay attention to different versions
18 - Valve stem seal
♦ replacing ⇒ page 15-28
19 - Valve spring
♦ removing and installing
20 - Valve spring retainer
21 - valve collets
22 - Bucket tappet
♦ do not mix up
♦ oil contact surface
♦ place down with contact surface fac-
♦ before installing, inspect axial play of
♦ inspecting ⇒ page 15-27
♦ removing and installing
23 - Bearing cap/inlet camshaft
♦ must be located on dowel sleeves
♦ pay attention to installation position
♦ installation sequence ⇒ page 15-16
tion
insert notch in the inlet camshaft.
ening and tightening
sprocket points outwards and the TDC
marking is visible on the 1st cylinder.
⇒ page 13-11, Fig. 2
⇒ page 15-28
ing down
camshaft ⇒ page 15-15
⇒ page 15-28
15
------------ 15-13 ------------