Base - ALLIANCE AE9133 Service Manual

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
IMPORTANT: The igniter is very fragile. Be careful
not to damage it during removal.
(6) Remove screw holding burner housing to
heat shroud. Refer to Figure 18.
(7) Remove screw holding front of burner
housing to dryer base and remove housing
out through front of dryer. Refer to
Figure 14.
(8) Remove four screws holding shroud to
heater box and remove shroud out through
front of dryer. Refer to Figure 18.
o. Electric Models
(1) Remove two screws holding heater
assembly to heater box, then pull heater
assembly down and away from heater box.
Refer to Figure 19.
p. Remove screw holding heat shield to dryer
base. Refer to Figure 34.
q. Remove one screw holding rear bulkhead to
terminal block bracket. While supporting
bulkhead, remove five screws holding rear
mounting brackets to rear of dryer cabinet and
remove the assembly out of the dryer. Refer to
Figure 34.
r. Remove screw holding bracket on exhaust duct
to rear of dryer cabinet and pull duct out
through rear of cabinet. Refer to Figure 22.
s. Remove two screws from each rear cabinet top
hold-down bracket (hinges). Refer to
Figure 36.
t. Remove screw holding access plate and remove
plate. Refer to Figure 22.
u. Remove two screws holding terminal block
bracket to cabinet. Refer to Figure 36.
v. Remove wire harness clips.
w. Remove guide lugs and screws.
x. Remove two screws from front edge at each
side of cabinet. Refer to Figure 30. Then
remove remaining screws from around the
bottom of cabinet and lift cabinet off base.

59. BASE

a. Remove two screws from the bottom edge of
the front panel. Refer to Figure 12.
60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
WARNING
b. Swing the bottom of the panel away from the
dryer to disengage hold-down clips and guide
lugs from cabinet top. Refer to Figure 12.
c. Disconnect wires from door switch. Refer to
Figure 13.
NOTE: Refer to appropriate wiring diagram when
rewiring switch.
d. Gas Models
(1) Disconnect igniter wires at disconnect
blocks, sensor wires from sensor terminals,
and wires from gas valve coils at the quick
disconnect blocks. Refer to Figure 14.
(2) Close main gas shut-off valve and gas shut-
off valve inside of dryer. Refer to
Figure 14.
(3) Disconnect gas line to dryer.
(4) Remove three screws holding gas valve
bracket to base and remove valve with lead-
in pipe attached. Refer to Figure 18.
(5) Remove screw from right side of burner
housing, holding burner tube in place.
Refer to Figure 14.
(6) Gently move burner tube toward rear of
dryer to disengage tab from slot on left side
of burner housing. Refer to Figure 18.
(7) Carefully rotate burner tube and igniter
counterclockwise so tab is at 8 o'clock
position and CAREFULLY remove burner
tube and igniter assembly out through front
of dryer.
IMPORTANT: The igniter is very fragile. Be careful
not to damage it during removal.
(8) Remove screw holding front of burner
housing to dryer base. Refer to Figure 19.
(9) Remove four screws holding shroud to
heater box and remove shroud and burner
housing out through front of dryer. Refer to
Figure 18.
e. Electric Models
Section 5 Service Procedures
W001R1
53