1. Manuals
  2. Brands
  3. ALLIANCE Manuals
  4. Dryer
  5. NE 6313
  6. Service manual

ALLIANCE AE9133 Service Manual

Ae/ag/ne/ng series home laundry dryers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Home Laundry
Dryers
"AE", "AG", "NE" and "NG" Models
Refer to Page 6 for Model Numbers
Part No. 60549R3
www.comlaundry.com
April 2002

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AE9133 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ALLIANCE AE9133

Summary of Contents for ALLIANCE AE9133

  • Page 1 Home Laundry Dryers “AE”, “AG”, “NE” and “NG” Models Refer to Page 6 for Model Numbers Part No. 60549R3 www.comlaundry.com April 2002...

  • Page 2: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 3 83. Symptom: Heater Does Not Turn On Or No Starting Serial No. S6271976XG ....123 Heat ..............85 84. Symptom: Improper Heat Or Drying Times ..86 85. Symptom: “oP” appears in Time display ..87 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 4: Section 1 - Safety Information

    • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R1 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 5: Locating An Authorized Servicer

    Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.

  • Page 6: Section 2 - Introduction

    Nameplate Location When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on nameplate(s) as shown. NAMEPLATE 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 7: Model Identification

    VG3019 NE8333 NE6513 NE4613 NE2113 NG8339 NG6519 NG4619 NG2119 NE7513 NE6313 NE4513 NG7519 NG6319 NG4519 NE7313 NE5513 NE4313 NG7319 NG5519 NG4319 AE7133 NE5313 AE4113 AG7139 NG5319 AG4119 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 8: How Your Dryer Works

    The heated air moves through the heater duct and into the cylinder, where it circulates through the wet load. The air then passes through the lint filter, air duct, and exhaust fan, where it is vented to the outdoors. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 9 Section 2 Introduction Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 10: Section 3 - Troubleshooting

    †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. *Mechanical Timer Models Only †Electronic Control Models Only 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 11: Motor Overload Protector Cycles Repeatedly

    • Test timer and replace if inoperative. †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. *Mechanical Timer Models Only †Electronic Control Models Only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 12: Heater Assembly Does Not Heat Or Burner Does Not Ignite

    †Read-out on electronic control indicates “OP”. • Thermistor is open, replace thermistor. Broken, loose, or incorrect wiring. • Refer to appropriate wiring diagram. *Mechanical Timer Models Only †Electronic Control Models Only 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 13: Igniter Does Not Glow (Gas Supply Sufficient) - Gas Models

    Sensor installed improperly on burner housing. • Loosen screw and properly position the sensor on the burner housing. *Mechanical Timer Models Only †Electronic Control Models Only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 14: Heater Assembly Or Burner Shuts Off Prematurely

    • Test thermistor and replace if inoperative. Air leak at blower seal. • Check and replace seal if necessary. *Mechanical Timer Models Only †Electronic Control Models Only 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 15: Heater Assembly Or Burner Does Not Shut Off

    Gas Models: Gas line pressure too high or too low. • If natural gas line pressure to dryer exceeds 8 inch water column pressure, or is lower than 4 inch water column, ask gas company to correct. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 16: Timer Does Not Advance In Automatic Cycle (Mechanical Timer Models Only)

    • Test timer and replace if inoperative. Improper or inadequate exhaust system. • Refer to Installation Instructions (supplied with dryer) for exhaust requirements. *Mechanical Timer Models Only †Electronic Control Models Only 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 17 Section 3 Troubleshooting Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 18: Section 4 - Grounding

    Models with painted exhaust fan cover – ground wire not used on unpainted covers) Figure 2 GROUND WIRE DRY832S GROUND WIRE Figure 1 GROUND WIRE DRY833S Figure 2 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 19: Neutral At Terminal Block To Terminal Block Bracket And Front Terminal Block Bracket To Control Housing (Electric Models Only)

    TERMINAL BLOCK BRACKET TO CONTROL HOUSING (Electric Models Only) Figure 3 GROUND WIRES GROUND WIRE DRY1051S DRY835S THROUGH SERIAL NO. S6271975XG STARTING SERIAL NO. S6271976XG Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 20: Wall Receptacle Polarity Check (Gas Models Only)

    TO CONTROL HOUSING. WALL RECEPTACLE POLARITY CHECK (Gas Models Only) Figure 4 NOTE: For determining GROUND the correct polarity of a WIRE wall receptacle. GROUND NEUTRAL NEUTRAL SIDE GROUND WIRE V.A.C. V.A.C. V.A.C. DRY1052S Figure 4 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 21: From Terminal Block Bracket To Timer Mounting Bracket To Dryer Cabinet Top. Timer

    CONTROL TO GRAPHIC PANEL BRACKET TO GRAPHIC PANEL (Electronic Control Model Dryers) (Mechanical Timer Model Dryers Only) Figure 6 Figure 5 GROUND WIRES GROUND WIRES Figure 6 DRY1053S Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 22: Section 5 - Service Procedures

    HOOD SCREW DRY1071S DRY1071S GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Models AG9139, AE9133, NG8639, NE8633, NG8539, NE8533, NG8339, NE8333, NG7139, NE7133, NG6539, NE6533,NG6339 and NE63330 Figure 7 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 23 GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Models NG6619, NE6613, NG6519, NE6513, NG6319, NE6313, NG5519, NE5513, NG5319, NE5313, AG5119, AE5113, VG5019, VE5013, NG4719, NE4713, NG4619, NE4613, NG4519, NE4513, NG4319 and NE4313) Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 24 ASSEMBLY LOCKING TABS TIMER SCREW TABS GRAPHIC PANEL END CAP (Right) SLOT TIMER KNOB DRY1796S GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Models NG2119 and NE2113) Figure 9 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 25: To Test Timer Contact Points

    Low Temperature Heat L2 and H1 — — — L2 and H1 — (Delicate) and H2 Push-to-Start — M and S M and S — — — © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 26: Temperature Switch

    Bend the tabs on the graphic panel (located inside of control hood) straight out toward rear of hood. d. Carefully remove the graphics panel off the front of the control hood. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 27: Lint Filter

    “Front” facing the front of the dryer. 29. LOADING DOOR Remove four screws holding hinges to door. Refer to Figure 10. HINGE SCREWS DRY1055S LINT FILTER FRONT AIR DUCT Figure 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 28: Inner And Outer Door Panels And Door Handle

    HEX HEAD STRIKER SCREW DOOR SEAL INNER DOOR PANEL DOOR DOOR ASSEMBLY HANDLE SPEED PHILLIPS HEAD SCREW OUTER DOOR PANEL PHILLIPS HEAD DOOR SCREW HINGE DRY850S Figure 11 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 29: Front Panel And Panel Seal

    HOLD-DOWN FRONT DOOR DOOR CLIP SWITCH PANEL SWITCH TABS GUIDE SEAL STRIKER LOCKNUT CATCH DRY1056S Figure 13 SCREW ACCESS DOOR DRY1057P SCREW DOOR HINGE Figure 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 30: To Test Door Switch

    Compress hold-down clips and remove from slot in top flange of front panel. Refer to Figure 12. e. Remove four screws holding four guide lugs to front panel. Refer to Figure 12. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 31: Burner System Operation (Gas Models)

    Both coils must be energized to open split-coil valve. Once opened, the holding coil can hold the valve open without assistance from the booster coil. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 32: Ignition System Features (Gas Models)

    120 VOLT, 60 HERTZ SECONDARY ELECTRICAL HOLDING COIL COIL SUPPLY LINE BOOSTER COIL SECONDARY COIL SENSOR HOLDING COIL IGNITER BOOSTER COIL Wiring Schematic D146SE3A Figure 15 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 33: To Test Electrical Circuit To Ignition System (Gas Models)

    Figure 14. burner housing have been removed from dryer. (7) Lift gas valve and mounting bracket from base. Refer to Figure 14. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 34: To Test Igniter (Gas Models)

    (4) Remove wires from sensor terminals. Refer NORTON to Figure 18. IGNITER AND BRACKET (5) Remove screw holding sensor to burner housing. Refer to Figure 18. DRY952S Figure 17 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 35: To Test Sensor (Gas Models)

    SCREW SHROUD BURNER HOUSING SENSOR ATTACHING SCREW IGNITER DISCONNECT BLOCK BURNER TUBE SENSOR SCREW IGNITER D241S VALVE SHUT-OFF VALVE (Shown in the UNION off position) Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 36: Burner Housing And Heat Shroud

    While thermostat is still hot, apply meter probes to thermostat terminals 1 and 2; meter should read “infinite” until thermostat cools at which time the meter should read “zero.” 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 37: Heater Assembly

    NOTE: When reassembling, be sure all wire NOTE: Refer to the appropriate wiring diagram connectors are tight on element terminals, thermal when rewiring the switch. fuse and limit thermostat. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 38: High Or Low Thermostat Or Thermostat And Heater Or Thermistor

    Meter should read read 2,400 Ohms ± 240 Ohms cold. “infinite”. If meter does not register any Ohms, replace both the thermal fuse and the limit thermostat. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 39: To Test Heater Assembly (Electric Models)

    Refer to Figure 21. NOTE: When reassembling, be sure felt seal on exhaust fan cover makes air tight seal on flange of duct. Refer to Figure 20. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 40: Exhaust Duct

    Refer to Figure 12. Figure 23 c. Disconnect wires from door switch. Refer to Figure 13. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 41 Refer to Figure 24. IDLER LEVER MOTOR PULLEY DRY862S INCORRECT WAY BELT IDLER PULLEY MOTOR PULLEY IDLER LEVER BELT ON WRONG SIDE OF IDLER LEVER D248S Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 42: To Test Drive Motor

    4. Put test meter probes on terminal 4 and motor “zero” Ohms. frame. Meter should register “no reading” or infinite. MOTOR AND EXHAUST ASSEMBLY MOTOR SWITCH DRIVE MOTOR GROUND WIRE DRY956S Figure 25 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 43 NOTE: Refer to SECTION IX, “Internal Wiring of (1) Disconnect wires from motor switch. Refer Dryer Motor Switch,” when rewiring the internal to Figure 26. switch wires. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 44: Cylinder Light

    Lift front of cabinet top and disengage from hinges on rear of cabinet. Refer to Figure 29. h. Remove control hood rear panel when DRY852S replacing cabinet top. Figure 28 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 45: Front Bulkhead Assembly

    If present, disconnect cylinder light wires. f. Remove four screws holding bulkhead to front flange of cabinet and lift complete bulkhead assembly out of slots in cabinet. Refer to Figure 30. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 46: Cylinder Belt

    Swing the bottom of the panel away from the dryer to disengage hold-down clips and guide lugs from cabinet top. Refer to Figure 12. c. Disconnect wires from door switch. Refer to Figure 13. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 47 IMPORTANT: On models using unpainted, ELONGATED corrosion resistant, coated steel cylinder, the BAFFLE elongated baffle must be installed to cover the cylinder seam weld. Refer to Figure 32. Figure 32 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 48: Rear Seal

    6 o’clock position and carefully remove the exhaust fan cover. cylinder out through front of dryer. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 49: Rear Bulkhead And Heater Box Assemblies

    Loosen two cabinet top hold-down screws. Refer to Figure 30. Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 50 (1) Refer to Figure 35 for removal. and wires from gas valve coils at the quick disconnect blocks. Refer to Figure 14. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 51: Terminal Block Or Power Cord

    (6) Remove all wires from terminal block. NOTE: Refer to appropriate wiring diagram when rewiring terminal block. (7) Remove screw holding terminal block to bracket. Refer to Figure 36. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 52 HINGES BRACKET DRY950S TERMINAL BLOCK SCREWS GROUND INSULATION WIRE TERMINAL BLOCK BRACKET TERMINAL BLOCK ATTACHING SCREW DRY1062S Through Serial No. S6271975XG Starting Serial No. S6271976XG Figure 36 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 53: Cabinet

    8 o’clock position. (5) Move air shutter end of burner tube slightly to right and CAREFULLY remove burner tube and igniter assembly out through front of dryer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 54: Base

    59. BASE e. Electric Models a. Remove two screws from the bottom edge of the front panel. Refer to Figure 12. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 55 Refer to Figure 26. m. Remove screw holding bracket on exhaust duct to rear of cabinet and pull duct out through rear of cabinet. Refer to Figure 22. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 56: Section 6 - Adjustments

    NOTE: If these locknuts are not tight, the dryer will not stay level during operation. d. Place a rubber cup (supplied with dryer) under each of the leveling legs. DRY868S LOCKNUT LEVELING RUBBER Figure 37 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 57: Burner Flame - Gas Models

    D399S f. Reinstall the access door. SHUTTER WARNING For personal safety, the access door must Figure 38 be in place during normal operation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 58: Section 7 - Gas Burner Conversion Procedures

    Remove pressure tap pipe plug and check gas pressure by connecting a “U ” tube manometer (or similar pressure gauge) to the pressure tap . Refer to Figure 39. DRY961S PRESSURE Figure 39 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 59: Installing The No. 401P3 Kit

    (3) Start dryer, pressure should be 10 ± 1.5 the closed position. Refer to Figure 41. inches (25.4, ± 3.8 cm). Refer to Figure 41. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 60 A a soapy solution. harsh, roaring, very blue flame indicates too much air.) Adjust air shutter to obtain a soft uniform blue flame as follows: 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 61 Reinstall the access door and screw. WARNING For personal safety, access door must be in place during normal operation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 62 Remove pressure tap pipe plug and check gas pressure by connecting a “U ” tube manometer (or similar pressure gauge) to the pressure tap . Refer to Figure 45. DRY961S PRESSURE Figure 45 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 63: Installing The No. 402P3 Kit

    PRESSURE TAP DRY967S PIPE PLUG the closed position. Refer to Figure 41. Figure 47 b. Disconnect igniter wires at quick disconnect blocks. Refer to Figure 47. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 64 Refer to Figure 50 . Figure 48 (3) Start dryer, pressure should be 3.5 ± .2 inches (8.89 ± .508 cm). Refer to Figure 50. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 65 “e”. (2) Installed the vent screw, see step “g”. (3) Gas valve pressure must be 3.5 ± .2 inches (8.89 ± .508 cm), see step “l”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 66: Section 8 - Service Procedures Unique To Electronic Control Model Dryers

    PERM PRESS EXTRA DRY TIME DRYING DELICATES NORMAL LESS COOL KNITS DAMP SIGNAL STOP DOWN MEMORY RESET NO HEAT WRINKLE - FREE WRINKLE-FREE SAVE DRY1798S LEVEL I 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 67 LEVEL II Model Level Part No. AG9139, AE9133, NG8639, NE8633, NG8539 and NE8533 59608 NG8339 and NE8333 59610 AG7139, AE7133, NG6539 and NE6533 59609 NG6339 and NE6333 59611 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 68: Dryer Operation

    (available free option has been selected. Clothes on some may be removed from the dryer at any models) time during the wrinkle-free portion. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 69: Customizing Programmed Cycles

    Press LESS to subtract drying time from the cycle. One press of the pad will change the time in one-minute intervals. Pressing and holding the pad down will © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 70: Signal

    Pressing the pad a third time will result in setting the loudest tone. To turn the signal off, press the pad until the SIGNAL 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 71: Electrical Service (Electric Dryers)

    TERMINAL BLOCK NOTE: Connect the dryer to the power IN DRYER supply with the MAXIMUM RATED VOLTAGE listed on the nameplate. DRY1063S PIGTAIL CONNECTION DIRECT CONNECTION Figure 53 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 72 (4) Secure the strain relief to the power cord, or wires, where they enter the dryer cabinet. (5) Reinstall access cover and screw. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 73 CORD operate the dryer with the WIRING POWER CORD access cover removed. W136 DIRECT WIRE) GROUND SCREW DRY1064S Starting Serial No. S6271976XG Figure 54 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 74 To reduce the risk of electric shock, terminals (i.e., red to red, white to white disconnect the electrical service to the and black to black) dryer before proceeding. W135 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 75 (10) Recheck all nuts or screws to be sure they are tight. (11) Reinstall the access plate and screw to the rear of the dryer cabinet. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 76 To reduce the risk of an electric shock, NEVER POWER CORD operate the dryer with the (FOUR-WIRE) access cover removed. GROUND W136 SCREW DRY1803S Starting Serial No. S6271976XG Figure 56 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 77: Electrical Requirements (Gas Dryers)

    NOTE: A qualified electrician should check the polarity of the wall receptacle. If a voltage reading is measured other than that illustrated, the qualified electrician should correct DRY1066S the problem. Figure 58 Figure 57 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 78: Service Procedures For Troubleshooting Electronic Control

    IMPORTANT: The diagnostic cycle is not intended local electrical utility company check it and to diagnose any components built into the control correct any problems. (i.e. relays, transformer, capacitors, etc.). 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 79 (NO) THERMISTOR (P6) NEUTRAL WHITE (P3) THERMISTOR (P5) TRANSFORMER DOOR SWITCH GRAY (P2) BROWN GROUND (P1) GREEN (P4) MOTOR RELAY K1 DRY1068S ELECTRONIC CONTROL BOARD Figure 59 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...
  • Page 80 1. This test routine will only light in the LED’s pertaining to the hardware model selected. 2. When the last step in the table is finished, the routine sequence will repeat. 3. East output is on for two seconds. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 81: Symptom: Failure Symptom

    If the symptom or problem corresponds to one of the symptoms detailed on the following pages, proceed to that flow chart. (The diagnostic cycle check does not have to be made.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 82: Symptom: Flashing Display

    “P2” and “P3” when door is closed door switch to the control. and “0” Volts when door is open? Recheck from beginning. If problem persists, replace control. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 83: Symptom: Blown Fuse Or Tripped Circuit Breaker

    Check heater circuit for shorted, broken, loose or incorrect wiring. *This measurement should be made with a digital Multi-Meter set at 200 Ohm scale for best precision. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 84: Symptom: Control Will Not Wake Up (No Led's Light) After Select Pad Is Pressed

    *This measurement should be made with a digital Multi-Meter set at 200 Ohm scale for best precision. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 85: Symptom: Control Wakes Up (When Select Pad Is Pressed) But Motor Does Not Start Properly

    Did you hear relay click and do you read approximately 120 Volts Replace control. between terminals “P1” (fan) and “P3” (neutral)? Check motor overload protector, motor and motor switch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 86: Symptom: Heater Does Not Turn On Or No Heat

    Replace control. seconds? Verify that orange wire is connected to terminal “N.O.” on heat relay K2. Check motor switch, limit thermostat, exhaust, heater assembly or gas valve. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 87: Symptom: Improper Heat Or Drying Times

    (thermistor). Plug in power cord and still exists, always replace the press the REGULAR and GO pads. thermistor before replacing the control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 88: Symptom: "Op" Appears In Time Display

    30° F. Did “oP” appear in display after Normal operation. three minutes. Recheck from beginning. If problem persists, always replace thermistor before replacing the control. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 89: Symptom: "Sh" Appears In Time Display

    “SH” condition if replace control. the temperature near thermistor is above 175° F. Cool thermistor down and go to "Symptom: Improper Heat Or Drying Times", Paragraph 84. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 90: Control Replacement

    When removing wires from wrapped properly. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 91 Section 8 Service Procedures Unique to Electronic Control Model Dryers Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 92: Section 9 - Internal Wiring Of Dryer Motor Switch

    W001R1 DRY1070S GENERAL ELECTRIC MOTOR WITH INTERNAL SWITCH MAIN WINDING START WINDING OVERLOAD PROTECTOR DRY869S GENERAL ELECTRIC MOTOR WITH EXTERNAL SWITCH 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 93 W001R1 MAIN WINDING START WINDING OVERLOAD PROTECTOR 4 BLU 7 BLK 5 YEL DRY870S EMERSON MOTOR WITH EXTERNAL SWITCH © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 94: Section 10 - Wiring Diagrams

    W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 95: Models Ag9139, Ng8639, Ng8539, Ng8339, Ag7139, Ng6539 And Ng6339

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AG9139, NG8639, NG8539, NG8339, AG7139, NG6539 AND NG6339 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 96: Models Ae9133, Ne8633, Ne8533, Ne8333

    W030 MODELS AE9133, NE8633, NE8533, NE8333, AE7133, NE6533 AND NE6333 Through Serial No. S6271975XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 97: Starting Serial No. S6271976Xg

    W030 MODELS AE9133, NE8633, NE8533, NE8333, AE7133, NE6533 AND NE6333 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 98: Models Ng7519 And Ng7319

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG7519 AND NG7319 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 99: Models Ne7513 And Ne7313

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE7513 AND NE7313 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 100: Models Ng6619, Ng5519, Ng5319 And Ag5119 Through Serial No. S6271975Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG6619, NG5519, NG5319 AND AG5119 Through Serial No. S6271975XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 101: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG6619, NG5519, NG5319 AND AG5119 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 102: Models Ne6613, Ne5513, Ne5313 And Ae5113 Through Serial No. S6271975Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE6613, NE5513, NE5313 AND AE5113 Through Serial No. S6271975XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 103: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE6613, NE5513, NE5313 AND AE5113 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 104: Models Ng6519 And Ng6319 Through Serial No. S6271975Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG6519 AND NG6319 Through Serial No. S6271975XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 105: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG6519 AND NG6319 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 106: Models Ne6513 And Ne6313 Through Serial No. S6271975Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE6513 AND NE6313 Through Serial No. S6271975XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 107: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NE6513 AND NE6313 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 108: Models Ng4519 And Ng4319 Through Serial No. S6242593Xd

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG4519 AND NG4319 Through Serial No. S6242593XD 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 109: Model Vg5019, Ng4519 And Ng4319 Starting Serial No. S6242594Xd And Continuing Through Serial No. S6271975Xg

    W030 MODEL VG5019, NG4519 AND NG4319 Starting Serial No. S6242594XD and continuing through Serial No. S6271975XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 110: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL VG5019, NG4519 AND NG4319 Starting Serial No. S6271976XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 111: Model Ve5013

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL VE5013 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 112: Model Ng4719 And Ng4619 Through Serial No. S6242593Xd

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NG4719 AND NG4619 Through Serial No. S6242593XD 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 113: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NG4719 AND NG4619 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 114: Model Ne4713 And Ne4613 Through Serial No. S6242593Xd

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NE4713 AND NE4613 Through Serial No. S6242593XD 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 115: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NE4713 AND NE4613 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 116: Model Ne4513 And Ne4313 Through Serial No. S6242593Xd

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NE4513 AND NE4313 Through Serial No. S6242593XD 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 117: Starting Serial No. S6242594Xd And Continuing Through Serial No. S6271975Xg

    W030 MODEL NE4513 AND NE4313 Starting Serial No. S6242594XD and continuing through Serial No. S6271975XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 118: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NE4513 AND NE4313 Starting Serial No. S6271976XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 119: Models Ag4119, Ng3519, Ng3319 And Vg3019

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AG4119, NG3519, NG3319 AND VG3019 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 120: Models Ae4113, Ne3513 And Ne3313 Through Serial No. S6242593Xd

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AE4113, NE3513 AND NE3313 Through Serial No. S6242593XD 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 121: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AE4113, NE3513 AND NE3313 Starting Serial No. S6271976XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 122: Models Ng2119

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG2119 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 123: Models Ne2113 Through Serial No. S6271975Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE2113 Through Serial No. S6271975XG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

  • Page 124: Starting Serial No. S6271976Xg

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE2113 Starting Serial No. S6271976XG 60549 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 125 Section 10 Wiring Diagrams Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60549...

This manual is also suitable for:

Ne8633Ne8533Ne8333Ne7513Ae7133Ne6613 ... Show all

Table of Contents