Canon imageRUNNER 2530 Service Manual page 180

No. Tx/Rx
##0671 [Rx] At time of V.8 arrival, procedure fails to move to phase 2 after detection of CM
signal from caller, causing T1 time-out and releasing line.
##0672 [Tx] At time of V.34 transmission, a shift in procedure from phase 2 to phase 3
and the reafter stops, causing the machine to release the line and suffer T1
timeout.
##0673 [Rx] At time of V.34 reception, a shift in procedure from phase 2 to phase 3 and
thereafter stops, causing the machine to release the line and suffer T1 timeout.
##0674 [Tx] At time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to
the control channel and thereafter stops, causing the machine to release the
line and suffer T1 timeout.
##0675 [Rx] At time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the
control channel and thereafter stops, causing the machine to release the line
and suffer T1 timeout.
##0750
[Tx] At time of ECM transmission, no meaningful signal is received after
transmission of PPS-NULL, causing the procedural signal to be transmitted
more than specified.
##0752 [Tx] At time of ECM transmission, DCN is received after transmission of PPS-
NULL..
##0753 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-NULL, or T5 time-out (60 sec) has
occurred.
##0754 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-NULL.
##0755 [Tx] At time of ECM transmission, no meaningful signal is received after
transmission of PPS-MPS, causing the procedural signal to be transmitted
more than specified.
##0757 [Tx] At time of ECM transmission, DCN is received after retransmission of PPS-
MPS.
##0758 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-MPS, or T5 time-out (60 sec) has
occurred.
##0759 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-MPS.
##0762 [Tx] At time of ECM transmission, DCN is received after transmission of PPS-
EOM.
##0763 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-MPS, or T5 time-out (60 sec) has
occurred.
##0764 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-EOM.
##0765
[Tx] At time of ECM transmission, no meaningful signal is received after
transmission of PPS-EOP, causing the procedural signal to be transmitted
more than specified.
##0767 [Tx] At time of ECM transmission, DCN is received after transmission of PPS-EOP.
##0768 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-EOP, or T5 time-out (60 sec) has
occurred.
7
Error Code > Error Code > FAX Error Codes > Service Error Code
Description
7 Error Code > Error Code > FAX Error Codes > Service Error Code
No. Tx/Rx
##0769 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of PPS-EOP, or T5 time-out (60 sec) has
occurred.
##0770 [Tx] At time of ECM transmission, no meaningful signal is received after
transmission of EOR-NULL, causing the procedural signal to be transmitted
more than specified.
##0772 [Tx] At time of ECM transmission, DCN is received after transmission of EOR-
NULL..
##0773 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of EOR-NULL, or T5 time-out (60 sec) has
occurred.
##0774 [Tx] At time of ECM transmission, ERR is received after transmission of EOR-
NULL..
##0775
[Tx] At time of ECM transmission, no meaningful signal is received after
transmission of EOR-MPS, causing the procedural signal to be transmitted
more than specified.
##0778 [Tx] At time of ECM transmission, the procedural signal has been transmitted
more than specified after transmission EOR-MPS, or T5 time-out (60 sec) has
occurred.
##0779 [Tx] At time of ECM transmission, ERR is received after transmission of EOR-
MPS.
##0780 [Tx] At time of ECM transmission, no meaningful signal is received after
transmission of EOR-EOM, causing the procedural signal to be transmitted
more than specified.
##0782 [Tx] At time of ECM transmission, DCN is received after transmission of EOR-
EOM.
##0783 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of EOR-EOM, or T5 time-out (60 sec) has
occurred.
##0784 [Tx] At time of ECM transmission, no meaningful signal is received after
transmission of EOR-EOP, causing the procedural signal to be transmitted
more than specified.
##0787
[Tx] At time of ECM transmission, DCN is received after transmission of EOR-EOP.
##0788 [Tx] At time of ECM transmission, the procedural signal has been transmitted more
than specified after transmission of EOR-EOP, or T5 time-out (60 sec) has
occurred.
##0789 [Tx] At time of ECM transmission, ERR is received after transmission of EOR-EOP.
##0790 [Rx] At time of ECM reception, ERR is transmitted after transmission of EOR-Q.
##0791 [Tx] While ECM mode procedure is under way, a signal other than a meaningful
signal is received.
##0792 [Rx] At time of ECM reception, PPS-NULL cannot be detected over partial page
processing.
##0793 [Rx] At time of ECM reception, no effective frame is received while high-speed
signal reception is under way, thus causing time-out.
##0794 [Tx] At time of ECM reception, PPR with all 0s is received.
##0795 [Tx/Rx] A fault has occurred in code processing for communication.
7-10
Description
T-7-4 T-7-4
7-10