Canon imageRUNNER 2530 Service Manual page 175

Ecode Detail Item
Code
E110 0002 Title Failure of the Scanner Motor (M21)
Description The speed lock signal indicates a deviation 10 times in
sequence at intervals of 100 msec after the signal has
indicated a locked state.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E110 0003 Title Failure of the Scanner Motor (M21)
Description The scanner motor (M21) speed lock signal does not indicate
a locked state for 6.5 sec. after a switchover is made from
low to normal speed or for 8 sec. after a switchover is made
from normal to low speed.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E196 0000 Title Error in EEPROM access
Description 20 retries failed after error occurred during communication
with EEPROM.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Replace the DC Controller PCB (PCB4).
E197 0000 Title Error in communication of Laser Driver PCB (PCB14)
Description Communication error 1 with image PCB
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E197 0001 Title Error in communication of Laser Driver PCB (PCB14)
Description Communication error 2 with image PCB
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E202 0000 Title There is an error in the detection of the CIS home position.
Description 1.The attempt to detect the home position fails when the CIS
is moved forward.
2.The attempt to detect the home position fails when the CIS
is moved back.
Remedy 1.Disconnect and then connect the flexible cable(Relay PCB
(PCB2)-Main Controller PCB (PCB1) 64pin).
2.Replace the flexible cable.
3.Replace the CIS HP sensor (S31).
4.Replace the Scanner Motor (M31).
5.Replace the Relay PCB (PCB2).
6.Replace the Main Controller PCB (PCB1).
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Ecode Detail Item
Code
E240 0000 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is constantly detected.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E240 0001 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is detected while printing.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E246 0000 Title Writing to the counter PCB (FRAM) failed
Description -
Remedy -
E247 0000 Title Mismatched checksum between the Flash Rom and the
FRAM
Description -
Remedy -
E261 0000 Title Error in Zero Cross
Description Zero Cross failed to be detected for 500ms or more while the
relay was ON.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E350 0000 Title SOFT-ID PCB error
Description -
Remedy -
E354 0000 Title Mismatched serial number for the SOFT-ID PCB
Description -
Remedy -
E355 0000 Title Mismatched serial number between the SOFT-ID, the Flash
Rom and the FRAM
Description -
Remedy -
E355 0004 Title System information error
Description -
Remedy -
E355 0005 Title System information error
Description -
Remedy -
E500 0000 Title Communication error
Description The communication with the host machine is interrupted.
Remedy 1.Check the cable.
2.Replace the Finisher Controller PCB (PCB1).
3.Replace the DC Controller PCB.
7-5
Description
7-5