Error Code; Error Code Details - Canon imageRUNNER 2530 Service Manual

Error Code

Error Code Details

Ecode Detail Item
Code
E000 0001 Title Fixing temperature abnormal rise
Description The temperature detected by the main thermistor does not
rise to the specified value during startup control.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Check connection of the Connectors (Thermistor Connector
and AC Connector).
3.Replace the Fixing Main Thermistor (Film Unit).
4.Replace the Fixing Assembly.
5.Replace the DC Controller PCB (PCB4).
E001 0000 Title Fixing unit temperature rise detection
Description The reading of the main thermistor is 250 deg C or more
continuously for 200 msec.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Check connection of the Connectors (Thermistor Connector
and AC Connector).
3.Replace the Fixing Main Thermistor (Film Unit).
4.Replace the Fixing Assembly.
5.Replace the DC Controller PCB (PCB4).
E001 0001 Title Fixing unit temperature rise detection
Description The hardware circuit detects overheating of the main or sub
thermistor for 200 msec.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Replace the DC Controller PCB (PCB4).
E001 0002 Title Fixing unit temperature rise detection
Description The reading of the sub thermistor is 295 deg C or more
continuously for 200 msec.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Check connection of the Connectors (Thermistor Connector
and AC Connector).
3.Replace the Fixing Main Thermistor (Film Unit).
4.Replace the Fixing Assembly.
5.Replace the DC Controller PCB (PCB4).
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Ecode Detail Item
Code
E002 0000 Title Fixing unit temperature insufficient rise
Description 1.The reading of the main thermistor is less than 115 deg C
continuously for 400 msec 1.3 sec after it has indicated 100
deg C.
2.The reading of the main thermistor is less than 150 deg C
continuously for 400 msec 1.3 sec after it has indicated 140
deg C.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Check connection of the Connectors (Thermistor Connector
and AC Connector).
3.Replace the Fixing Main Thermistor (Film Unit).
4.Replace the Fixing Assembly.
5.Replace the DC Controller PCB (PCB4).
E003 0000 Title Low fixing temperature detection after standby
Description The reading of the main thermistor is less than 140 deg C
continuously for 400 msec or more.
Remedy 1.Go through the following to clear the error: CLEAR >
ENGIN > ERRCLR; and then turn OFF and then ON the
power.
2.Check connection of the Connectors (Thermistor Connector
and AC Connector).
3.Replace the Fixing Main Thermistor (Film Unit).
4.Replace the Fixing Assembly.
5.Replace the DC Controller PCB (PCB4).
E004 0000 Title Thermistor disconnection detection error
Description When disconnection is detected with connector (J214) for 30
sec continuously.
Remedy 1.Check connection of the Connector (J214).
2.Replace the Film Unit.
3.Replace the Fixing Assembly.
4.Replace the DC Controller PCB (PCB4).
E010 0001
Title Unstable rotation of the Main Motor (M1)
Description Detection is executed every 100 msec after the start of motor
rotation; however, the drive detection signal is absent for 2
sec.
Remedy 1.Replace the Main Motor (M1).
2.Replace the DC Controller PCB (PCB4).
E010 0002 Title Unstable rotation of the Main Motor (M1)
Description During motor rotation, detection is executed every 100 msec;
however, the drive signal is absent 5 times in sequence.
Remedy 1.Replace the Main Motor (M1).
2.Replace the DC Controller PCB (PCB4).
7-3
Description
7-3