Specifications; 2.0L Dohc Engine - Chrysler PT Cruiser Service & Repair Manual

PT
ENGINE 2.0L DOHC (Continued)
(39) Install oil filter. Fill engine crankcase with
proper oil to correct level.
(40) Fill power steering system.
(41) Fill cooling system (Refer to 7 - COOLING/
ENGINE - STANDARD PROCEDURE).
(42) Evacuate and recharge A/C system (Refer to
24 - HEATING & AIR CONDITIONING - STAN-
DARD PROCEDURE).
(43) Start engine and run until operating temper-
ature is reached.
(44) Perform torque strut adjustment procedure
(Refer to 9 - ENGINE/ENGINE
TORQUE STRUT - ADJUSTMENTS).
(45) Adjust transmission linkage, if necessary.

SPECIFICATIONS

2.0L DOHC ENGINE

DESCRIPTION
General Specification
Type
Number of Cylinders
Displacement
Bore
Stroke
Compression Ratio
Firing Order
Compression Pressure
Max. Variation Between
Cylinders
Cylinder Block
Cylinder Bore Diameter
Out-of-Round (Max.)
Taper (Max.)
Piston Diameter
MOUNTING/
SPECIFICATION
In-Line OHV, DOHC
4
2.0 Liters
(122 cu. in.)
87.5 mm
(3.445 in.)
83.0 mm
(3.268 in.)
9.6:1
1-3-4-2
1172–1551 kPa
(170–225 psi)
25%
87.4924–87.5076 mm
(3.4446–3.4452 in.)
0.051 mm
(0.002 in.)
0.051 mm
(0.002 in.)
Pistons
87.463–87.481 mm
(3.4434–3.4441 in.)
ENGINE 2.0L DOHC
DESCRIPTION
Clearance @ 17.5 mm
(11/16 in.) from bottom of
skirt
Weight
Land Clearance
(Diametrical)
Piston Length
Piston Ring Groove
Depth No. 1
Piston Ring Groove
Depth No. 2
Piston Ring Groove
Depth No. 3
Piston Pins
Clearance in Piston
Clearance in Connecting
Rod
Diameter
End Play
Length
Piston Rings
Ring Gap—Top
Compression Ring
Wear Limit
Ring Gap—2nd
Compression Ring
Wear Limit
Ring Gap—Oil Control
Steel Rails
Wear Limit
Ring Side Clearance—
Compression Rings
Wear Limit
9 - 89
SPECIFICATION
0.018–0.050 mm
(0.0007–0.0020 in.)
340–350 grams
(11.99–12.34 oz.)
0.740–0.803 mm
(0.029–0.031 in.)
64.8 mm
(2.551 in.)
3.983–4.132 mm
(0.157–0.163 in.)
4.456–4.605 mm
(0.175–0.181 in.)
3.841–4.075 mm
(0.151–0.160 in.)
0.008–0.020 mm
(0.0003–0.0008 in.)
Interference
20.998–21.003 mm
(0.8267–0.8269 in.)
None
74.75–75.25 mm
(2.943–2.963 in.)
0.23–0.52 mm
(0.009–0.020 in.)
0.8 mm
(0.031 in.)
0.49–0.78 mm
(0.019–0.031 in.)
0.8 mm
(0.031 in.)
0.23–0.66 mm
(0.009–0.026 in.)
1.0 mm
(0.039 in.)
0.025–0.065 mm
(0.0010–0.0026 in.)
0.10 mm
(0.004 in.)