Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....13 Ignition Key Removal ....13 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate ..24 To Lock The Doors And Liftgate (If Equipped With Power Options) ..25 Using The Panic Alarm .
Page 11 Emergency Deck Lid Release Latch (Convertible) ......41 Power Windows ......42 Auto Down Feature .
Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Tips ......112 Exhaust Gas ......112 Safety Checks You Should Make Inside The Vehicle .
Page 13: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 15: Key-In-Ignition Reminder
Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: With the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transpon- der) fault unless the additional part is physically held...
Page 17: Sentry Key Programming
Sentry Key Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
Page 18: Steering Wheel Lock - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 19 Door Lock Plunger WARNING! For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 20: Power Door Locks
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Automatic Door Locks—If Equipped The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1.
Page 21 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position. 3. Depress the power door lock switch to lock the doors. 4.
Page 22: Child-Protection" Door Lock System (Rear Doors) - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Child-Protection” Door Lock System (Rear Doors) — If Equipped To provide a safer environment for children riding in the rear seat, the rear doors have the “child-protection” door lock system. To use the system, open each rear door and move the control UP to engage.
Page 23: Remote Keyless Entry (Sedan)
WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
Page 24: To Unlock The Doors And Liftgate
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate.
Page 25: To Lock The Doors And Liftgate (If Equipped With Power Options)
NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5.
Page 26: To Turn Off "Flash Lights With Lock
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of...
Page 27 NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle. Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key: 1.
Page 28: General Information
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally. NOTE: If you do not have a programmed transmitter, contact your dealer for details.
Page 29: Remote Keyless Entry (Convertible)
Separating Transmitter Halves 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together.
Page 30: To Unlock The Doors
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters. To Unlock the Doors Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate.
Page 31: To Lock The Doors
NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5.
Page 32: Using The Panic Alarm
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
Page 33: To Program Additional Transmitters
Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. To Program Additional Transmitters NOTE: If vehicle is equipped with the optional Elec- tronic Vehicle Information Center (EVIC) in the instru- ment cluster, the transmitters may also be programmed...
Page 34: General Information
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This transmitter complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Page 35: Security Alarm System - If Equipped
2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. SECURITY ALARM SYSTEM —...
Page 36: To Disarm The System
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Unlock a front door/liftgate using the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle.
Page 37: Liftgate (Sedan)
LIFTGATE (SEDAN) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate (if equipped). Rotate the key and pull the liftgate up. To unlock the liftgate, insert the key into the lock and turn to the right.
Page 38: Deck Lid (Convertible)
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
Page 39: Power Deck Lid Release (Convertible)
Gas props support the deck lid in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the deck lid in cold weather. Power Deck Lid Release (Convertible) You can open the deck lid by pressing the Remote Keyless Entry Button or from inside the vehicle, using the switch located inside the glove box.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Emergency Seat Back Release Once unlatched the seat back can be pushed forward to gain access into the interior of the vehicle.
Page 41: Emergency Deck Lid Release Latch (Convertible)
EMERGENCY DECK LID RELEASE LATCH (CONVERTIBLE) WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the deck lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
Page 42: Power Windows
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS The power window switches are located on the instru- ment panel above the radio. The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger’s window and the lower right switch controls the right rear passenger’s window.
Page 43: Auto Down Feature
WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment may result in serious injury or death.
Page 44: Wind Buffeting
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 45: Lap/Shoulder Belts
Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate Inserting Latch Plate Into Buckle...
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. •...
Page 49 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 50: Adjustable Upper Shoulder Belt Anchorage
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched.
Page 51: Lap/Shoulder Belt Untwisting Procedure
Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 52: Seat Belt Pretensioners
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Page 53: Seat Belts And Pregnant Women
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recom- mend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver’s seat belt.
Page 54: Driver And Front Passenger Supplemental Restraint System (Srs) - Airbag
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint...
Page 55 regulations that define Occupant Classification (Refer to Occupant Classification System in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! •...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the driver inflatable knee blocker to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
Page 57 If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Front Seat Mounted Side Airbags (If equipped) •...
Page 59 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system.
Page 61 For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child re- straints).
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improp- erly classified.
Page 63 may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC Module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items previously mentioned. In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas.
Page 65 The front passenger seat assembly contains critical com- ponents that affect the front passenger airbag deploy- ment. Correctly functioning front passenger seat compo- nents are critical for the Occupant Classification System (OCS) to properly classify the front passenger and calcu- late the proper airbag deployment.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an acci- dent.
Page 67 irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufac- turer’s instructions for cleaning.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately.
Page 69 identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
Page 70: Child Restraint
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 71 • Safety experts recommend that rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back;...
Page 73 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again.
Page 75 the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCH- compatible child seats such that two seats share a com- mon lower anchorage. If you are installing LATCH- compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehi- cle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
Page 77 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
Page 79: Occupant Restraints (Convertible)
OCCUPANT RESTRAINTS (CONVERTIBLE) Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and if equipped, side airbags for both the driver and front passenger.
Page 80: Lap/Shoulder Belts
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts. If the belt webbing is twisted, and comes in contact with the wearers body, the twisted belt should be corrected using the Lap/Shoulder belt untwisting procedure found in this section.
Page 81 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. •...
Page 82 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 83 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 84 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 85: Lap/Shoulder Belt Untwisting Procedure
Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180°...
Page 86: Enhanced Seat Belt Reminder System
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
Page 87: Seat Belts And Pregnant Women
4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled.
Page 88: Driver And Front Passenger Supplemental
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 89 regulations that define Occupant Classification (Refer to Occupant Classification System in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 WARNING! •...
Page 90 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the driver inflatable knee blocker to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
Page 91 If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly.
Page 92 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Front Seat Mounted Side Airbags (If equipped) •...
Page 93 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
Page 94 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers push- ing down on the seat will also be sensed.
Page 95 For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child re- straints).
Page 96 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improp- erly classified.
Page 97 may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
Page 98 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door.
Page 99 • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle.
Page 100 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: •...
Page 101 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 102 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
Page 103: Child Restraint
Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 104 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 105 weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag.
Page 106 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 107 into the retractor, as the belt retracts, you will hear a clicking sound. This indicates that the seat belt is now in the automatic locking mode. Pull on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture.
Page 108 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat cushion. They are round bars, part of the seat and body structure, and are readily visible. In addition, there are two tether strap anchorages located behind the rear seat head form, in the convertible top storage area. Latch Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available.
Page 109 installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it.
Page 110 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To gain access to the achorages, locate the child tether anchorage decals on the carpet behind the rear seat head forms and use a small screwdriver to pry the carpet flap open. The carpet flap is attached in two different places.
Page 111: Engine Break-In Recommendations
over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible.
Page 112: Safety Tips
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.
Page 113: Inside The Vehicle
Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 114 114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil or other fluid leaks. Also, if gasoline fumes are detected or fuel, power steering fluid or brake fluid leaks are suspected, the cause should be located and corrected immediately.
Page 115: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....119 To Lower The Top ..... 119 To Raise The Top .
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ System Features ... . . 145 Advanced Phone Connectivity ... . 149 Things You Should Know About Your UConnect™...
Page 117 Daytime Running Lights (DRL) — If Equipped ......180 Lights-On Reminder ....180 Fog Lights —...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation ......196 Reprogramming A Single Button ..196 Security .
Page 119: Convertible Top Operation
CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top.
Page 121 Releasing Convertible Top Latches 3. Press the Power Top Switch to lower the top just enough to disengage the top pins from the header, turn the handle counterclockwise and raise the handle to the stowed position. NOTE: The Power Top Switch has two detent positions for lowering the convertible top.
Page 122: To Raise The Top
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section. CAUTION! Damage to the convertible top boot cover could result if the latch handle is not completely closed...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 1. Remove the convertible top boot cover, if equipped. Refer to Convertible Top Boot Cover Removal and Stor- age, in this section. 2. Turn the ignition to the ON position. 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches.
Page 124: Convertible Top Boot Cover Installation-If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Car top carriers, ski racks, etc., should not be at- tached to the convertible top mechanism as they will damage the top. Do not place objects on the convert- ible top, in the top well or on the sport bar. Damage to the convertible top may occur.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails. Boot Laying Across Convertible Top...
Page 126 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged. Tucking Boot Under Rail Engaging Boot Arm Snaps...
Page 127 4. Engage the boot center section retainer using the tabs provided. Engaging Boot Center Section UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 5. Tuck the rear flap of the boot in behind the Upper Moulding. Tucking In Rear Flap...
Page 128: Convertible Top Boot Cover Removal And Storage
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car. Boot Removed And Laying Flat...
Page 129 3. First fold the left side of the boot cover to the middle of the boot cover. Folding Boot Cover Left Side 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area.
Page 130: Convertible Top Manual Override
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area.
Page 131: Mirrors
3. Using the latch handle raise the top until the two pins seat themselves in the windshield header. 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. Engaging Convertible Top Latches UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 6.
Page 132: Outside Mirror-Driver's Side
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Adjusting Rear View Mirror Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of...
Page 133: Electric Remote-Control Mirrors - If Equipped
Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. To adjust the view in the outside mirrors, turn the rotary knob to the left (L), center (O) or Right (R) position. After selecting the mirror, move the knob in the same direction you want the mirror to move.
Page 134: Sun Visor Sliding Feature
UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones.
Page 135 UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name.
Page 136: Operations
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UCon- nect™...
Page 137 Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual.
Page 138 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing and follow the audible prompts.
Page 139 Call/Dial by Saying a Number • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Dial. • System will prompt you to say the number you want call. • For example, you can say 234-567-8901. •...
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Phonebook New Entry. • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended.
Page 141 • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
Page 142: Phone Call Features
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After confirmation, the phonebook entries will be de- leted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. •...
Page 143 Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call.
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’...
Page 145: Uconnect™ System Features
• After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. •...
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Emergency and the UConnect™...
Page 147 Paging To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to Working with Automated Systems.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. •...
Page 149: Advanced Phone Connectivity
Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: •...
Page 150 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names •...
Page 151: Things You Should Know About Your Uconnect™ System
Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • At the next prompt, say Delete and follow the prompts. • You can also press the Voice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete.
Page 152 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
Page 153 Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. •...
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155...
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 157: Seats
North American English Primary Alternate(s) Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up Phone settings phone set SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor.
Page 158: Power Seat Adjuster - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Power Seat Switch Recliner Control Lever This seat also has a manual recline lever located just to the rear of the power seat switch. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever.
Page 160: Manual Lumbar-If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar—If Equipped The Lumbar adjustment is located on the inboard side of the driver’s seat. To increase support, rotate the handle down. Lumbar Adjust Handle Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space.
Page 161: Driver's Seat Back Tilt-If Equipped
Driver’s Seat Back Tilt—If Equipped How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward. 3. To return seat to a sitting position, push seat back rearward. NOTE: The driver’s front seat has a full recliner memory, which will allow the seat back to return to its original position.
Page 162: Adjustable Head Restraints
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push seat back forward until it slides toward the dashboard. Passenger Seat Back Tilt Lever 3. To return seat to a sitting position, rotate seat back upright until it locks. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory, which will allow the seat back to returned to its original position.
Page 163: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 164 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the instru- ment panel, below the radio. After turning on the igni- tion, you may choose OFF, HIGH, or LOW heat settings. An indicator on the switch shows which setting has been chosen.
Page 165: Folding Rear Seat (Sedan)
Folding Rear Seat (Sedan) To provide additional storage area, each rear seatback can be folded forward. Push and hold the buttons shown in the picture to fold down either or both seatbacks. Folding Rear Seat Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! •...
Page 166: Folding Rear Seat (Convertible)
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the seatback is properly latched and the rear center lap/shoulder belt still does not operate properly check and see if the Automatic Locking retractor (ALR) system is activated. WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the seatback is in the fully upright and locked position when occupied.
Page 167 Folding Rear Seat Release Knobs UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 168: Tumbling Rear Seat (Sedan)
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat (Sedan) To provide additional storage in the cargo area, each rear seat can be tumbled forward. CAUTION! It is important that the front seats be pulled forward to the midpoint of the seat track to avoid contact between the rear seat and the front seatback.
Page 169 • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. Tumbling Seat Release Strap • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place.
Page 170: Tumbling Rear Seat (Convertible)
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat (Convertible) To provide additional storage area, each rear seat can be tumbled forward. CAUTION! It is important that the front seats be pulled forward to the midpoint of the seat track to avoid contact between the rear seat and the front seatback.
Page 171 2. From inside the vehicle, fold the rear seat back down flat. Folding Rear Seat Back UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward. Tumbling Rear Seat...
Page 172 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure. Cinching Tether Strap To return the tumbling rear seat to the latched (normal) position use the following procedure:...
Page 173 The strap should be reinstalled in the side NOTE: pocket on the seat cushion before returning the seat to the latched (normal) position. NOTE: Prior to rotating the seat cushions rearward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible.
Page 174: Rear Seat Removal (Sedan)
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Removal (Sedan) The rear seats can be removed to provide more cargo space. • Push and hold the button on the seatback and fold down the rear seatback. Folding Rear Seat Button •...
Page 175 Release Lever Location • Using the handle on the seat, the seat assembly can now be lifted and removed from the vehicle. NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle.
Page 176: To Open And Close The Hood
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood.
Page 177: Lights
WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Map/Reading Lights (Sedan) These lights are mounted between the sun visors above the rear view mirror.
Page 178: Map/Reading Lights (Convertible)
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights (Convertible) When the ignition switch is in the ON position, these lights, located under the rearview mirror can be turned on by switches located at the base of the rearview mirror. NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
Page 179: Headlights, Parking Lights, Instrument Panel Lights
Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Headlamp Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
Page 180: Daytime Running Lights (Drl) - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gear shift is in any position except park.
Page 181: Turn Signals
NOTE: The fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Turn Signal Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 182: Highbeam/Lowbeam Select Switch
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch Highbeam, Lowbeam, and Passing Lights Push the Multi-Function Control Lever away from you to switch the headlights to HIGH beam. Pull the Lever toward you, to switch the headlights back to Low beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward...
Page 183: Windshield Washers
Wiper/Washer Switch Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low speed for two wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
Page 184: Windshield Wiper Operation
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the control to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 185: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, push down on the lever below the multifunction control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. Tilt Steering Column Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 WARNING! Tilting the steering column while the vehicle is...
Page 186 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, press the TCS switch until the traction control indicator in the instrument cluster lights Traction Control Switch To turn the system back ON, press the switch a second time until the traction control indicator turns OFF.
Page 187: Electronic Speed Control - If Equipped
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 35 mph (56 km/h). The speed control lever is located on the right side of the steering wheel. Speed Controls UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 To Activate: Push the ON/OFF button.
Page 188: To Set At A Desired Speed
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever.
Page 189: Manual Transaxle
Tapping the “SET DECEL” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. Manual Transaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal.
Page 190: Garage Door Opener - If Equipped
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 191 HomeLink Buttons (Convertible) For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 192: Programming The Universal Transceiver
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Universal Transceiver For best results, install a new battery in the hand held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down.
Page 193 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view. Proper Transceiver Training Distance UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 HomeLink Programming (Convertible) 4.
Page 194: Rolling Code" Programming
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure.
Page 195: Canadian Programming/Gate Programming
NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com.
Page 196: Operation
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor.
Page 197: Power Sunroof - If Equipped
2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink is a trademark owned by Johnson Controls, Inc.
Page 198: Express Open Feature
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward.
Page 199: Wind Buffeting
WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
Page 200: Electrical Power Outlets
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The outlets include tethered caps, labeled with a key symbol or battery symbol, indicating power source. All outlets are protected by a single 20 Amp fuse. The standard outlet in the front of the center floor console is a conventional cigar lighter outlet.
Page 201 Center Console Power Outlet This outlet is powered directly by the battery, regardless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to protect the battery against discharge.
Page 202: Electrical Outlet Use With Engine Off
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 203: Storage
CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine start- ing.
Page 204 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console provides a sliding armrest with two unique storage compartments under the lid. Sliding Armrest Storage Bins Push the upper button on the front of the armrest to raise the upper cover. Inside is a slot for a power cord, an area to store a cell phone, and other miscellaneous items.
Page 205: Storage Pockets
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 206: Position 1 (Top)
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. • Failure to follow these warnings could result in serious or fatal injury.
Page 207: Position 2 (Middle)
Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. Rear Shelf Panel Position 2 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle).
Page 208: Position 4 (Vertical)
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward. Push the shelf panel forward to lock it into place. Rear Shelf Panel Position 4 WARNING! When in the vertical position, the rear shelf panel...
Page 209 2. Twist the knob on the underside of the panel and lower the shelf leg. Rear Shelf Leg Release Knob 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Rear Shelf Panel Position 5 WARNING! Do not load objects over 100 lbs (45 kg) in position 5...
Page 210: Roof Luggage Rack - If Equipped
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
Page 211 CAUTION! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
Page 213: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....216 Instrument Cluster—Base ....217 Instrument Cluster—Premium .
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances ....237 AM Reception ..... . . 237 FM Reception .
Page 215 Electronic Serial Number/Sirius Identification Number (ESN/SID) ....260 Selecting Satellite Mode In REF, And RAQ, Radios ......261 Selecting a Channel .
Page 216: Instrument Panel Features
216 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES...
Page 217: Instrument Cluster-Base
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INSTRUMENT CLUSTER—BASE...
Page 218: Instrument Cluster-Premium
218 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM...
Page 219: Instrument Cluster-Turbo
UNDERSTANDING YOUR INSTRUMENT PANEL 219 INSTRUMENT CLUSTER—TURBO...
Page 220: Instrument Cluster Descriptions
220 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle.
Page 221 5. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. Transmission Range Indicator This display indicator shows the automatic transmission gear selection.
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start.
Page 223 12. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anti-lock brake system.
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
Page 225 17. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 18. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds.
Page 226: Understanding Your Instrument Panel 213
226 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer.
Page 227: Electronic Vehicle Information Center (Evic)-If Equipped
ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)–If Equipped EVIC Location The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine tem- perature gauge. The EVIC consists of the following: UNDERSTANDING YOUR INSTRUMENT PANEL 227 •...
Page 228 228 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages. • Turn Signal On (with a continuous warning chime) • Left Front Turn Signal Lamp Out (with a single chime) •...
Page 229: Evic Functions
EVIC Functions EVIC Button Press the EVIC button until one of the following func- tions are displayed on the EVIC: • Compass/Temperature/Audio • Average Fuel Economy UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Distance To Empty (DTE) • Elapsed Time • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the resettable function currently being displayed.
Page 230: Compass/Temperature/Audio
230 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Audio Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside temperature and the current radio station. For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section.
Page 231: Elapsed Time
Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. Personal Settings (Customer Programmable Features) This allows the driver to set and recall features when the transmission is in PARK (automatic transmission) or the...
Page 232 232 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock On Exit When ON is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped (manual transmissions) or the vehicle is stopped and the transmission is in P (Park) or N (Neutral) position (automatic transmissions).
Page 233 when exiting the vehicle. Press and hold the EVIC button when in this display until 0, 30, 60, or 90 appears to make your selection. Headlamps On With Wipers (Available with Auto Headlights Only) When ON is selected and the headlight switch is in the AUTO position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL Display English or Metric The EVIC, odometer, and navigation system units can be changed between English and Metric. Press and hold the EVIC button when in this display until “US” or “METRIC” appears to make your selection. Compass Variance Compass Variance is the difference between magnetic North and Geographic North.
Page 235 To set the variance: with the ignition in the ON position, with a short button press (less than one seconds) press and release the EVIC button several times until you have displayed the Personal Settings (Customer Program- mable Features) menu. Once in the Personal Settings (Customer Programmable Features) menu, press and release (less than one seconds) the EVIC button several times until “Compass Variance”...
Page 236: Setting The Analog Clock
236 UNDERSTANDING YOUR INSTRUMENT PANEL calibration mode. The Cal indicator will come on con- tinuously in the EVIC display to indicate that the com- pass is now in the calibration mode and that the vehicle can now be driven to calibrate. (A short EVIC button press from the Calibrate Compass (Yes) screen will exit the EVIC Customer Programmable features, and return it to its normal operating mode).
Page 237: Radio General Information
RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent”...
Page 238: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
238 UNDERSTANDING YOUR INSTRUMENT PANEL will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 239 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 241 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 242: Operation Instructions - Cd Mode
242 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 243 • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player. • This radio does not play discs with MP3 tracks. SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD.
Page 244: Operation Instructions - Auxiliary Mode
244 UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 245: Operating Instructions - Hands Free Phone - If Equipped
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. MUTE will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers.
Page 246: Operating Instructions - Satellite Radio - If Equipped
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 247 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 249 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: 16 Digit-Character Program Type No program type or un- defined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Foreign_Language Information Jazz News Display...
Page 251 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 252: Operation Instructions - (Cd Mode For Cd Audio Play)
252 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 253: Load/Eject Button
SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 254 254 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Page 255: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 3-character extension) • Level 2: 31 (including a separator 3-character extension) Multisession disc formats are supported by the radio.
Page 257 MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 258: Operation Instructions
258 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file.
Page 259 MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the MSG or INFO button once more to return to elapsed time priority mode.
Page 260: Satellite Radio - If Equipped
260 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to separate Video Entertainment System (VES ) Guide.
Page 261: Selecting Satellite Mode In Ref, And Raq, Radios
ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits.
Page 262: Selecting A Channel
262 UNDERSTANDING YOUR INSTRUMENT PANEL These radios will also display the current station name and program type. For more information such as song title and artist press the MSG or INFO button. A CD or tape may remain in the radio while in the Satellite radio mode.
Page 263: Pty Button Scan
PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the SCAN button a second time to stop the search.
Page 264: Reception Quality
264 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 265: Radio Operation And Cellular Phones
RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 266 266 UNDERSTANDING YOUR INSTRUMENT PANEL The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the OFF position.
Page 267 NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet.
Page 268 268 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red area indicates warmer tempera- tures.
Page 269 Circulation Control Use this button to choose be- tween outside air intake or recirculation of the air inside the vehicle. A lamp will illu- minate when you are in recir- culate mode. Only use the re- circulate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial...
Page 270: Operating Tips
270 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 271 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
Page 272: Rear Window Features
272 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
Page 273: Rear Wiper/Washer Switch - If Equipped
CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch — If Equipped A switch on the right side of the steering column controls operation of the rear wiper/washer function.
Page 274: Adding Washer Fluid
274 UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Page 275: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 278 Automatic Transaxle ....278 Manual Transaxle .
Page 276 276 STARTING AND OPERATING AutoStick General Information ... . 287 Manual Transaxle Operation ....288 2.4 Liter Turbo— If Equipped ... . . 289 Recommended Shift Speeds .
Page 277 Snow Tires ......317 Tire Rotation Recommendations ... . 317 Fuel Requirements .
Page 278: Starting Procedures
278 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 279: Manual Transaxle
Manual Transaxle Before starting the engine fully apply the parking brake, press the clutch pedal to the floor and place the gear selector in NEUTRAL. NOTE: The engine will not start unless the clutch pedal is pressed to the floor. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal.
Page 280: If Engine Fails To Start
280 STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds.
Page 281: Automatic Transaxle - If Equipped
TURBOCHARGER COOL DOWN CHART Driving Conditions Normal Driving Aggressive Driving or Heavily Loaded Trailer Tow AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
Page 282: Brake/Transmission Interlock System
282 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 283: Four Speed Automatic Transaxle
Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrat- ing; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and preci- sion shifts will develop within a few shift cycles.
Page 284 284 STARTING AND OPERATING brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selector in P (Park) position. WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
Page 285 CAUTION! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the steering wheel and shift lever are released. Other- wise, damage to the steering column or shifter could result. “R” Reverse Shift into this range only after the vehicle has come to a complete stop.
Page 286: Autostick - If Equipped
286 STARTING AND OPERATING “1” Low This range should be used for maximum engine braking when descending steep grades. In this range, up shifts will occur only to prevent engine over speed while down shifts from 2nd to first will occur as early as possible. AUTOSTICK —...
Page 287: Autostick General Information
Autostick General Information • The transmission will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored.
Page 288: Manual Transaxle Operation
288 STARTING AND OPERATING MANUAL TRANSAXLE OPERATION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline.
Page 289: 2.4 Liter Turbo- If Equipped
Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch. Never shift into REVERSE until the vehicle has come to a complete stop.
Page 290: Recommended Shift Speeds
290 STARTING AND OPERATING the shifter lever all the way to the right to avoid acciden- tally selecting THIRD gear. Also, use care when selecting FIRST gear to avoid accidentally selecting REVERSE. When moving the shifter lever into REVERSE press the lever to the left until the resistance is overcome.
Page 291: Downshifting
For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 2 (within legal speed limits). TABLE 2-MANUAL TRANSAXLE MAXIMUM PERFORMANCE SHIFT SPEEDS IN mph (km/h) ENGINE 1 to 2 2 to 3 3 to 4 SIZE 2.4L (48)
Page 292: Parking Brake
292 STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver.
Page 293: Brake System
When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
Page 294: Anti-Lock Brake System (Abs) - If Equipped
294 STARTING AND OPERATING If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop.
Page 295 WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 296 296 STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system per- forming its self check cycle to ensure that the ABS system is working properly.
Page 297: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 298: Traction Control - If Equipped
298 STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction.
Page 299: Tire Safety Information
TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. STARTING AND OPERATING 299 • European Metric tire sizing is based on European design standards.
Page 300 300 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 301 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 302: Tire Identification Number (Tin)
302 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 303: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 303 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 304 304 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 305 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 306 306 STARTING AND OPERATING...
Page 307: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 308: Tire Inflation Pressures
308 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 309 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 310 310 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 311: Radial-Ply Tires
Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 312: Limited Use Spare - If Equipped
312 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
Page 313: Tire Spinning
WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 314: Tread Wear Indicators
314 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 315: Replacement Tires
Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 316: Alignment And Balance
316 STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
Page 317: Snow Tires
SNOW TIRES Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire side wall. If you need snow tires, select tires equivalent in size and type to the original equipment tires.
Page 318: Fuel Requirements
318 STARTING AND OPERATING wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87.
Page 319: 2.4L High Output Turbo Engine
(with the ap- propriate octane rating for your engine) before consider- ing service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 320: Gasoline/Oxygenate Blends
320 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE.
Page 321: Materials Added To Fuel
It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformu- lated gasolines. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives.
Page 322: Carbon Monoxide Warnings
322 STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer.
Page 323: Adding Fuel
STARTING AND OPERATING 323 ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable container, it should have a flexible nozzle long enough to force open the restricting door. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the passen- ger’s side of the vehicle.
Page 324 324 STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
Page 325: Loose Fuel Filler Cap Message
NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
Page 326: Vehicle Loading
326 STARTING AND OPERATING VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Rear Seat Occupants (sedan) ....3 Rear Seat Occupants (convertible) .
Page 327 Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings in- clude a 68 kg (150 lbs) allowance for the presence of a driver).
Page 328 328 STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
Page 329: Trailer Hitch Classification
Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
Page 330: Trailer Towing Weights (Maximum Trailer Weight Ratings)
330 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area 2.4L N/A and 2.4L 20 Sq. Ft Turbo/Automatic* 2.4L N/A and 2.4L 20 Sq.
Page 331: Trailer And Tongue Weight
Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
Page 332: Towing Requirements
332 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information plac- ard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
Page 333 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 334 334 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires −...
Page 335 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. STARTING AND OPERATING 335 WARNING! Do not connect trailer brakes to your vehicle’s hy-...
Page 336: Towing Tips
336 STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector Towing Tips...
Page 337 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up.
Page 338: Recreational Towing (Behind Motorhome, Etc.)
338 STARTING AND OPERATING Towing Tips — Cooling System To reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral but do not increase engine idle speed. −...
Page 339: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....340 If Your Engine Overheats ....340 Jacking And Tire Changing .
Page 340: Hazard Warning Flasher
340 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Warning Switch The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
Page 341 the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off imme- diately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
Page 342: Jacking And Tire Changing
342 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual.
Page 343: Jack Location
Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. Jack Location Do not attempt to raise this vehicle using a bumper jack. WHAT TO DO IN EMERGENCIES 343 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism.
Page 344: Preparations For Jacking
344 WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire.
Page 345: Jacking Instructions
Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel.
Page 346 346 WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 347: Jump-Starting Procedures Due To A Low Battery
100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free.
Page 348 348 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- axle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 349: Driving On Slippery Surfaces
WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water.
Page 350: Traction
350 WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is danger- ous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.).
Page 351: Towing A Disabled Vehicle
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 352: Without The Ignition Key
352 WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the ACCESSORY posi- tion, not in the LOCK positions. Do not attempt to use sling type equipment when towing.
Page 353: Convertible Top Manual Override
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area.
Page 354 354 WHAT TO DO IN EMERGENCIES 5. Pull down and rotate the handle counterclockwise to engage the latches. Engaging Convertible Top 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely.
Page 355: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Turbo Engine Compartment ... . 358 2.4L Engine Compartment ....359 Onboard Diagnostic System —...
Page 356 356 MAINTAINING YOUR VEHICLE Maintenance-Free Battery ....371 Air Conditioner Maintenance ... . . 372 Power Steering —...
Page 357 Headlights ......401 Front Park/Turn Signal/Side Marker Lights . . 402 Front Fog Lights — If Equipped ... 402 Tail/Stop, And Rear Turn Signal Lights .
Page 358: 2.4L Turbo Engine Compartment
358 MAINTAINING YOUR VEHICLE 2.4L TURBO ENGINE COMPARTMENT...
Page 359: 2.4L Engine Compartment
MAINTAINING YOUR VEHICLE 359 2.4L ENGINE COMPARTMENT...
Page 360: Onboard Diagnostic System - Obd Ii
360 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 361: Emissions Inspection And Maintenance Programs
gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL).
Page 362: Replacement Parts
362 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station.
Page 363: Dealer Service
DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 364 364 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Engine Oil Dipstick Checking the oil while the vehicle is on level ground, will improve the accuracy of the oil level readings.
Page 365 • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. •...
Page 366 366 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American...
Page 367: Drive Belts - Check Condition And Tension
Materials Added To Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
Page 368: Spark Plugs
368 MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug.
Page 369: Engine Timing Belt
WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Page 370: Fuel Filter
370 MAINTAINING YOUR VEHICLE Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary.
Page 371: Maintenance-Free Battery
Maintenance-Free Battery You will never have to add water, nor is periodic main- tenance required. CAUTION! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides bat- tery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid.
Page 372: Air Conditioner Maintenance
372 MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Page 373: Power Steering - Fluid Check
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
Page 374: Front Suspension Ball Joints
374 MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 375: Windshield Wiper Blades
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing.
Page 376: Exhaust System
376 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged;...
Page 377: Cooling System
Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. •...
Page 378 378 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 379 Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 380 380 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precau- tion. Never add coolant when the engine is over- heated. Do not loosen or remove the cap to cool an overheated engine.
Page 381 Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator.
Page 382: Hoses And Vacuum/Vapor Harnesses
382 MAINTAINING YOUR VEHICLE Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold.
Page 383 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.
Page 384 384 MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on.
Page 385: Automatic Transaxle
WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. You could have an accident. CAUTION! Use of improper brake fluids will affect overall clutch system performance.
Page 386 386 MAINTAINING YOUR VEHICLE refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recom- mended fluid. CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
Page 387 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 24 km (15 miles). The fluid cannot be comfortable held between the finger tips.
Page 388: Manual Transaxle
388 MAINTAINING YOUR VEHICLE Maintenance schedule “B”—All Engines – Every 60,000 miles (100 000 km) change fluid and filter under the following conditions: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation.
Page 389: Appearance Care And Protection From Corrosion
Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately.
Page 390 390 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.
Page 391 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. •...
Page 392 392 MAINTAINING YOUR VEHICLE • For grease stains, apply Mopar cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essen- tials products. Interior Care Use Mopar Total Clean to clean fabric upholstery and carpeting.
Page 393 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
Page 394: Convertible Top Care
394 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 395: Cloth Top Additional Cleaning Procedure
CAUTION! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates or plasticizers. always wait until the top is thoroughly dry before lowering it into the storage area. Scrub in all directions, covering an area of about two square feet at a time.
Page 396: Weather Strip Care
396 MAINTAINING YOUR VEHICLE CAUTION! Avoid getting Scotchguard_ on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur. Weather Strip Care Lubricate all top and door glass weather strips periodi- cally with Mopar Weather Strip Lubricant (part number 4773427), to keep them soft and pliable.
Page 397 Cavity Cartridge Mini Description Fuse Fuse 40 Amp Power Top Feed Green 20 Amp AWD ECU Feed Yellow 10 Amp CHMSL Brake Switch Feed 10 Amp Ignition Switch Feed 20 Amp Trailer Tow Yellow 10 Amp IOD Sw/Pwr Mir/ Ocm Steering Cntrl Sdar/Hfm 30 Amp IOD Sense1...
Page 398 398 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 10 Amp IOD Feed CVT Mod/ Mod_Wcm 40 Amp ASD Relay Contact Green PWR Feed 20 Amp PWR Amp 1 & Amp Yelow 2 Feed 15 Amp IOD Feed Radio Lt. Blue 10 Amp IOD Feed Intrus Mod/Siren...
Page 399 Cavity Cartridge Mini Description Fuse Fuse 10 Amp ABS MOD/J1962 Conn/PCM 30 Amp ABS Valve Feed Pink 40 Amp ABS Pump Feed Green 30 Amp Headlamp Washer Pink Control 25 Amp Spare Natural MAINTAINING YOUR VEHICLE 399 CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 400: Vehicle Storage
400 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw).
Page 401: Bulb Replacement
BULB REPLACEMENT Headlights CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. MAINTAINING YOUR VEHICLE 401 3.
Page 402: Front Park/Turn Signal/Side Marker Lights
402 MAINTAINING YOUR VEHICLE Front Park/Turn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. Front Fog Lights —...
Page 403: Back Up Lights
MAINTAINING YOUR VEHICLE 403 Back Up Lights Removing Backup Light Bulbs 3. Pull the bulb out of the socket and replace. 1. To remove the backup lamp, you must take a fiber stick and slide it along the inboard side of the lamp and compress a spring clip to allow it to partially pop out to the secondary catch.
Page 404: Center High Mounted Stop Light
404 MAINTAINING YOUR VEHICLE 2. Fully compress the clip to get the lamp to come out completely. 3. Remove the socket from the housing. 4. Pull the bulb out of the socket and replace. FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil.
Page 405: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 406: Chassis
406 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid. Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Page 407 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..408 Maintenance Schedule ....408 Schedule “B”—All Engines ....411 Schedule “A”—Non Turbo .
Page 408: Emission Control System Maintenance
408 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 409 • Taxi, police, or delivery service (commercial ser- vice).† • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines”...
Page 410 410 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 411: Schedule "B"-All Engines
SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an Change the manual transaxle fluid every 48,000 miles (80...
Page 412 412 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the Maintenance Sched- ules section of this manual.
Page 413 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as nec- essary. SCHEDULE “B”—ALL ENGINES 413 3,000 6,000 9,000...
Page 414 414 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the Make-up air filter.
Page 415 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.†...
Page 416 416 SCHEDULE “B”—ALL ENGINES Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.
Page 417 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and re- place as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals.
Page 418 418 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.†...
Page 419 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 420 420 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* 123,000 126,000 129,000 (205 000) (210 000) (215 000) 132,000...
Page 421 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Replace the spark plugs. Replace the Make-up air filter. Inspect the PCV valve and replace if necessary. *‡ * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 422: Schedule "A"-Non Turbo
422 SCHEDULE “A”—NON TURBO SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter.
Page 423 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles.
Page 424 424 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Replace the engine timing belt. * Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 425 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV valve and replace if necessary. * ‡ Replace the air cleaner filter. Flush and replace the engine coolant at 120 months, if not done at 102,000 miles. Replace the spark plugs and ignition cables.
Page 426 426 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV valve and replace if necessary. * ‡ Replace the air cleaner filter. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 427: Schedule "A"-Turbo
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 428 428 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles. 35,000 40,000 45,000 (56 000) (64 000) (72 000) [42] [48]...
Page 429 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 430 430 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 431 Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 433: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......434 Prepare For The Appointment .
Page 434: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 435 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 436 436 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 437: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 438: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 439: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 440: Temperature Grades
440 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 441 INDEX...
Page 442 442 INDEX ABS (Anti-Lock Brake System) ....294 Adding Engine Coolant (Antifreeze) ..379 Adding Fuel ......323 Adding Washer Fluid .
Page 443 Special Additives ..... . 388 Autostick ......286 Back-Up Lights .
Page 444 444 INDEX Caution, Exhaust Gas ..... 112 CD (Compact Disc) Player ....238,246 CD (Compact Disc) Player Maintenance .
Page 445 Coolant Level ..... . 377,380 Disposal of Used Coolant ....380 Drain, Flush, and Refill .
Page 446 446 INDEX Electronic Speed Control (Cruise Control) Electronic Vehicle Information Center (EVIC) ..227 Emergency Deck Lid Release Latch (Convertible) . . 41 Emergency, In Case of Jacking ......342 Jump Starting .
Page 447 Flooded Engine Starting ....280 Fluid, Brake ......406 Fluid Capacities .
Page 448 448 INDEX Gasoline, Reformulated ....320 Gauges Coolant Temperature ....220 Fuel .
Page 449 Instrument Cluster ....217,220 Instrument Panel and Controls ....216 Instrument Panel Cover .
Page 450 450 INDEX Engine Temperature Warning ....224 Fog ......180,225,402 Front Replacement .
Page 451 Schedule “B” ......411 Schedule “B”-All Engines ....411 Maintenance Schedules .
Page 452 452 INDEX Quality ......366 Recommendation ....366,404 Synthetic .
Page 453 Pretensioners Seat Belts ......52,85 Programmable Electronic Features ..192,196,231 Programming Transmitters (Remote Keyless Entry) .
Page 454 454 INDEX Safety Information, Tire ....299 Safety Tips ......112 Satellite Radio .
Page 455 Sentry Key (Immobilizer) ....15,36 Sentry Key Programming ....17 Service and Maintenance .
Page 456 456 INDEX Tether Anchor, Child Restraint ... . 74,107 Theft Alarm (Security Alarm) ....35 Theft System (Security Alarm) .
Page 457 Weight ......330 Traction ......350 Traction Control .
Page 458 458 INDEX Uniform Tire Quality Grades ....439 Universal Transmitter ..... 190 Unleaded Gasoline .

This manual is also suitable for:

Pt cruiser convertible 2007

Chrysler 2007 PT Cruiser Convertible Instruction Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2007 PT Cruiser Convertible

Summary of Contents for Chrysler 2007 PT Cruiser Convertible