Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....13 Ignition Key Removal ....13 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate ..25 To Lock The Doors And Liftgate (If Equipped With Power Options) ..26 Using The Panic Alarm .
Page 11 Emergency Deck Lid Release Latch (Convertible) ......41 Power Windows ......42 Auto Down Feature .
Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Tips ......114 Exhaust Gas ......114 Safety Checks You Should Make Inside The Vehicle .
Page 13: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 15: Key-In-Ignition Reminder
Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: With the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transpon- der) fault unless the additional part is physically held...
Page 17: Sentry Key Programming
Sentry Key Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
Page 18: Steering Wheel Lock - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 19 Door Lock Plunger WARNING! For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 20: Power Door Locks
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Automatic Door Locks—If Equipped The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1.
Page 21 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position. Ignition Key Position 3. Depress the power door lock switch to lock the doors. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Power Door Lock Switch 4.
Page 22 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. The Auto Unlock feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5.
Page 23: Child-Protection" Door Lock System (Rear Doors) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws. “Child-Protection” Door Lock System (Rear Doors) — If Equipped To provide a safer environment for children riding in the rear seat, the rear doors have the “child-protection”...
Page 24: Remote Keyless Entry (Sedan)
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
Page 25: Things To Know Before Starting Your Vehicle
NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
Page 26: To Lock The Doors And Liftgate (If Equipped With Power Options)
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
Page 27: To Turn Off "Flash Lights With Lock
The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle. Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key: 1.
Page 29: General Information
14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally. NOTE: If you do not have a programmed transmitter, contact your dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada.
Page 30: Battery Replacement
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal.
Page 31: Remote Keyless Entry (Convertible)
REMOTE KEYLESS ENTRY (CONVERTIBLE) Four Button Transmitter This system allows you to lock or unlock the doors or open the deck lid from distances of 23–50 feet (7–15 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters.
Page 32: To Lock The Doors
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1. Press and hold the LOCK button on a programmed key fob. 2.
Page 33: To Unlatch The Deck Lid
The “Sound Horn On Lock” and “Flash Lamps With Lock” feature can be reactivated by repeating this proce- dure. To Unlatch the Deck Lid Press the “Rear Release” button twice to unlatch the deck lid. Panic Alarm The panic mode flashes the park lights, and sounds the horn for about 3 minutes or until the alarm is turned off.
Page 34: To Program Additional Transmitters
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the LOCK position, and the key removed.
Page 35: General Information
General Information This transmitter complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation.
Page 36: Security Alarm System - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation.
Page 37: To Disarm The System
To disarm the system: Unlock a front door/liftgate using the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
Page 38: Liftgate (Sedan)
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE (SEDAN) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate (if equipped). Rotate the key and pull the liftgate up. To unlock the liftgate, insert the key into the lock and turn to the right.
Page 39: Deck Lid (Convertible)
WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed.
Page 40: Power Deck Lid Release
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the deck lid in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the deck lid in cold weather. Power Deck Lid Release You can open the deck lid by pressing the Remote Keyless Entry Button or from inside the vehicle, using the...
Page 41: Emergency Deck Lid Release Latch (Convertible)
seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Emergency Seat Back Release Once unlatched the seat back can be pushed forward to gain access into the interior of the vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: Make sure that the elastic loop is around the emergency release handle at all times.
Page 42: Power Windows
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a security measure, an emergency deck lid release lever is built into the deck lid latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in- the-dark lever attached to the deck lid latching mecha- nism.
Page 43: Auto Down Feature
The convertible has an All windows up and All windows down, switch located between the window switches instead of the lock switch. Power Window Switch THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! Never leave children in a vehicle, with the keys in the ignition switch.
Page 44: Rear Window Switches
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Window Switches There are also rear passenger window switches (sedan only) located at the rear of the center console. Rear Power Window Switches Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 45: Lap/Shoulder Belts
adult-size seat belts, your seat belts or the LATCH feature also, can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
Page 47 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Latch Plate to Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 49 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 51: Adjustable Upper Shoulder Belt Anchorage
WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seat back is in the fully upright and locked position when occu- pied. If the rear seat back is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, the vehicle should imme- diately be taken to your dealer for service.
Page 52: Lap/Shoulder Belt Untwisting Procedure
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. Positioning Latch Plate 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180°...
Page 53: Seat Belt Pretensioners
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing.
Page 54: Enhanced Seat Belt Reminder System (Beltalert)
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
Page 55: Seat Belts And Pregnant Women
4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Airbag Components NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
Page 57 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE empty or is occupied by someone that is classified in the “child category. This could be a child, a teenager, or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
Page 59 5. If the airbag system in this vehicle needs to be modified to accomodate a disabled person, contact the Customer Center. Phone numbers are provided under If You Need Assistance in Section 9 of this manual. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! •...
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Front Seat Mounted Side Airbags (If equipped) •...
Page 61 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers push- ing down on the seat will also be sensed.
Page 63 front passenger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs. For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improp- erly classified.
Page 65 may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC Module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items previously mentioned. In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas.
Page 67 The following requirements must be strictly adhered to: • Do not modify the front passenger seat assembly or components in any way. • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe col- lision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
Page 69 WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately.
Page 71 identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
Page 72: Child Restraint
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 73 • Safety experts recommend that rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) NOTE: additional information www.nhtsa.dot.gov or www.seatcheck.org. WARNING! •...
Page 75 restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE from the retractor. Allow the belt to return into the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. NOTE: To reset this feature you must let all of the belt webbing return into the retractor.
Page 77 Latch Anchorages Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 provide add-on tether strap kits for some of their older products.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
Page 79 Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the...
Page 80: Occupant Restraints (Convertible)
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. OCCUPANT RESTRAINTS (CONVERTIBLE) Some of the most important safety features in your vehicle are the restraint systems.
Page 81: Lap/Shoulder Belts
ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts. If the belt webbing is twisted, and comes in contact with the wearers body, the twisted belt should be corrected using the Lap/Shoulder belt untwisting procedure found in this section.
Page 82 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 83 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 84 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 85 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 86: Lap/Shoulder Belt Untwisting Procedure
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. Positioning Latch Plate 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180°...
Page 87: Seat Belt Pretensioners
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing.
Page 88: Enhanced Seat Belt Reminder System
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
Page 89: Seat Belts And Pregnant Women
4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled.
Page 90 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Airbag Components NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
Page 91 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 92 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE empty or is occupied by someone that is classified in the “child” category. This could be a child, a teenager, or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
Page 93 5. If the airbag system in this vehicle needs to be modified to accomodate a disabled person, contact the Customer Center. Phone numbers are provided under If You Need Assistance in Section 9 of this manual. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 WARNING! •...
Page 94 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Front Seat Mounted Side Airbags (If equipped) •...
Page 95 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
Page 96 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers push- ing down on the seat will also be sensed.
Page 97 child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passen- ger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs.
Page 98 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improp- erly classified.
Page 99 may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
Page 100 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door.
Page 101 • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle.
Page 102 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: •...
Page 103 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 104 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
Page 105: Child Restraint
• Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) •...
Page 106 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 107 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Page 108 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 109 belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again.
Page 110 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Latch Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time.
Page 111 restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
Page 112 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Strap Mounting Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts.
Page 113: Engine Break-In Recommendations
• Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
Page 114: Safety Tips
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING!
Page 115: Outside The Vehicle
Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first...
Page 117: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....121 To Lower The Top ..... 121 To Raise The Top .
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ System Features ... . . 147 Advanced Phone Connectivity ... . 152 Things You Should Know About Your UConnect™...
Page 119 Daytime Running Lights (DRL)(Canada Only) . 182 Lights-On Reminder ....182 Fog Lights — If Equipped ....183 Turn Signals .
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming . . 197 Operation ......198 Reprogramming A Single Button .
Page 121: Convertible Top Operation
CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top.
Page 123 Releasing Convertible Top Latches 3. Press the Power Top Switch to lower the top just enough to disengage the top pins from the header, turn the handle counterclockwise and raise the handle to the stowed position. NOTE: The Power Top Switch has two detent positions for lowering the convertible top.
Page 124: To Raise The Top
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section. CAUTION! Damage to the convertible top boot cover could result if the latch handle is not completely closed...
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 1. Remove the convertible top boot cover, if equipped. Refer to Convertible Top Boot Cover Removal and Stor- age, in this section. 2. Turn the ignition to the ON position. 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches.
Page 126: Convertible Top Boot Cover Installation-If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Car top carriers, ski racks, etc., should not be at- tached to the convertible top mechanism as they will damage the top. Do not place objects on the convert- ible top, in the top well or on the sport bar. Damage to the convertible top may occur.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails. Boot Laying Across Convertible Top...
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged. Tucking Boot Under Rail Engaging Boot Arm Snaps...
Page 129 4. Engage the boot center section retainer using the tabs provided. Engaging Boot Center Section UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 5. Tuck the rear flap of the boot in behind the Upper Moulding. Tucking In Rear Flap...
Page 130: Convertible Top Boot Cover Removal And Storage
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car. Boot Removed And Laying Flat...
Page 131 3. First fold the left side of the boot cover to the middle of the boot cover. Folding Boot Cover Left Side 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area.
Page 132: Convertible Top Manual Override
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area.
Page 133: Mirrors
3. Using the latch handle raise the top until the two pins seat themselves in the windshield header. 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. Engaging Convertible Top Latches UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 6.
Page 134: Outside Mirror-Driver's Side
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Adjusting Rear View Mirror Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of...
Page 135: Electric Remote-Control Mirrors - If Equipped
Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. To adjust the view in the outside mirrors, turn the rotary knob to the left (L), center (O) or Right (R) position. After selecting the mirror, move the knob in the same direction you want the mirror to move.
Page 136: Sun Visor Sliding Feature
UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones.
Page 137 UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name.
Page 138: Operations
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UCon- nect™...
Page 139 Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing.
Page 141 phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to Advanced Phone Connectivity ). Dial by Saying a Number •...
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect™ phone- book. Refer to Add Names to Your UConnect™ Phonebook, to learn how to store a name in the phonebook.
Page 143 four associated phone numbers and designations. Each language has a separate 32 name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. •...
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say List Names to hear a list of the entries in the phonebook from which you choose.
Page 145: Phone Call Features
• To call one of the names in the list, press the Voice Recognition’ button during the playing of the desired name and say Call. NOTE: the user can also exercise Edit or Delete operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call.
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say Dial or Call followed by the phone number or phonebook entry you wish to call.
Page 147: Uconnect™ System Features
Call Termination To end a call in progress, momentarily press the Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. •...
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection.
Page 149 emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Towing Assistance.
Page 150 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word Send.
Page 151 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™...
Page 152: Advanced Phone Connectivity
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number #121, you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect™...
Page 153 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin. •...
Page 154: Things You Should Know About Your Uconnect™ System
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition’ button anytime while the list is being played and say the priority number of the phone you wish to delete. Things You Should Know About Your UConnect™ System Voice Recognition (VR) •...
Page 155 • UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • You can say O (letter O ) for 0 (zero). 800 must be spoken eight-zero-zero. • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157...
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 159: Seats
North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Page 160: Power Seat Adjuster - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Power Seat Switch Recliner Control Lever This seat also has a manual recline lever located just to the rear of the power seat switch. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever.
Page 162: Manual Lumbar-If Equipped
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar—If Equipped The Lumbar adjustment is located on the inboard side of the driver’s seat. To increase support, rotate the handle down. Lumbar Adjust Handle Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space.
Page 163: Driver's Seat Back Tilt-If Equipped
Driver’s Seat Back Tilt—If Equipped How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward. 3. To return seat to a sitting position, push seat back rearward. NOTE: The driver’s front seat has a full recliner memory, which will allow the seat back to return to its original position.
Page 164: Adjustable Head Restraints
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push seat back forward until it slides toward the dashboard. Passenger Seat Back Tilt Lever 3. To return seat to a sitting position, rotate seat back upright until it locks. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory, which will allow the seat back to returned to its original position.
Page 165: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Heated Seats — If Equipped This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the instru- ment panel, below the radio. After turning on the igni- tion, you may choose OFF, HIGH, or LOW heat settings.
Page 166: Folding Rear Seat (Sedan)
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated.
Page 167 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts •...
Page 168: Folding Rear Seat (Convertible)
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Convertible) To provide additional storage area, each rear seatback can be folded forward. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
Page 169: Tumbling Rear Seat (Sedan)
WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Push and hold the button on the seatback and fold down the rear seatback. Folding Rear Seat Button • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. Tumbling Seat Release Strap •...
Page 171: Tumbling Rear Seat (Convertible)
Tumbling Seat Strap To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position. NOTE: The elastic strap should be reinstalled in the clip on the base of the seat cushion before returning the seat to its normal position.
Page 172 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the left side seatback. Pull the right side seatback release knob to fold down the right side seatback. Folding Rear Seat Release Knobs 2. From inside the vehicle, fold the rear seat back down flat.
Page 173 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward. Tumbling Rear Seat UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure.
Page 174 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To return the tumbling rear seat to the latched (normal) position use the following procedure: 1. Loosen the strap by pushing rearward on the cinching tether strap buckle. Releasing Cinching Tether Strap 2. Disconnect the cinching tether strap. NOTE: The strap should be reinstalled in the side pocket on the seat cushion before returning the seat to the...
Page 175: Rear Seat Removal (Sedan)
NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback. 3. Rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position. WARNING! In an accident, you or others in your vehicle could be injured if seats are not properly latched to their...
Page 176 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. Tumbling Seat Release Strap • Lift up the release levers to disengage the seat from the floor attachments.
Page 177: To Open And Close The Hood
To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat. Lift the seat back to its upright latched position.
Page 178: Lights
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood. Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position.
Page 179: Map/Reading Lights (Convertible)
NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Map/Reading Lights (Convertible) When the ignition switch is in the ON position, these lights, located under the rearview mirror can be turned on by switches located at the base of the rearview mirror.
Page 180: Interior Lights
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Interior Lights The interior lights come on when a door or deck lid (convertible) is opened.
Page 181: Multi-Function Control Lever
control is left in the Dome light position or a door is left open. The interior lights will remain on for only 90 seconds for all occurrence after that, until the engine is turned on and off. Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “OFF”...
Page 182: Headlights, Parking Lights, Instrument Panel Lights
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Multi-Function Lever Control Lever To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
Page 183: Fog Lights - If Equipped
Fog Lights — If Equipped The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever. NOTE: The fog lights will only operate with the head- lights on low beam.
Page 184: Windshield Wipers And Washers
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Rotate the control to select the desired wiper speed. Wiper/Washer Switch Windshield Washers To use the washer, pull the control lever toward you and...
Page 185: Windshield Wiper Operation
CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
Page 186: Rear Window Wiper/Washer (Sedan Models Only)
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the Park position. When the vehicle is restarted, the wipers will resume operation. Rear Window Wiper/Washer (Sedan Models Only) A switch on the right side of the steering column controls operation of the rear wiper/washer function.
Page 187: Tilt Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Page 188: Traction Control Switch - If Equipped
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 189: Electronic Speed Control - If Equipped
NOTE: The Traction Control System will make buzzing or clicking sounds when the system is in operation. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 35 mph (56 km/h). The speed control lever is located on the right side of the steering wheel.
Page 190: To Set At A Desired Speed
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
Page 191: Manual Transaxle
Tapping “RESUME ACCEL” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold “SET DECEL”.
Page 192: Garage Door Opener - If Equipped
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 193 HomeLink Buttons (Convertible) For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 194: Programming The Universal Transceiver
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Universal Transceiver For best results, install a new battery in the hand held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down.
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 HomeLink Programming (Sedan) HomeLink Programming (Convertible) 4. Using both hands, press the hand held transmitter button and the desired Universal Transceiver button. Do not release the buttons until step 5 has been completed. NOTE: Some entry gates and garage door openers may require you to replace step 4 with the procedures listed under Canadian Programming.
Page 196: Rolling Code" Programming
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure.
Page 197: Canadian Programming/Gate Programming
NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com.
Page 198: Operation
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor.
Page 199: Power Sunroof - If Equipped
2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink is a trademark owned by Johnson Controls, Inc.
Page 200: Express Open Feature
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward.
Page 201: Wind Buffeting
WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
Page 202 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Power Outlet It will accept a cigar lighter unit, which is part of the optional Smokers Package. To preserve the heating ele- ment of the cigar lighter unit, do not hold the lighter in the heating position.
Page 203 This outlet is powered directly by the battery, regardless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to protect the battery against discharge. The second is in the right rear cargo area. Rear Power Outlet UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Since this outlet is remote from the driver, it is powered...
Page 204: Electrical Outlet Use With Engine Off
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 205: Storage
CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine start- ing.
Page 206 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the upper button on the front of the armrest to raise the upper cover. Inside is a slot for a power cord, an area to store a cell phone, and other miscellaneous items. Push the lower button on the front of the armrest, and raise the armrest for access to the lower storage bin.
Page 207: Storage Pockets
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 208: Position 1 (Top)
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. • Failure to follow these warnings could result in serious or fatal injury.
Page 209: Position 2 (Middle)
Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. Rear Shelf Panel Position 2 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle).
Page 210: Position 4 (Vertical)
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward. Push the shelf panel forward to lock it into place. Rear Shelf Panel Position 4 WARNING! When in the vertical position, the rear shelf panel...
Page 211 2. Twist the knob on the underside of the panel and lower the shelf leg. Rear Shelf Leg Release Knob 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 Rear Shelf Panel Position 5 WARNING! Do not load objects over 100 lbs (45 kg) in position 5...
Page 212: Roof Luggage Rack - If Equipped
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
Page 213 CAUTION! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
Page 215: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....218 Instrument Cluster—Base ....219 Instrument Cluster—Premium .
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances ....239 AM Reception ..... . . 239 FM Reception .
Page 217 Electronic Serial Number/Sirius Identification Number (ESN/SID) ....262 Selecting Satellite Mode In REF, And RAQ, Radios ......263 Selecting a Channel .
Page 218: Instrument Panel Features
218 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES...
Page 219: Instrument Cluster-Base
UNDERSTANDING YOUR INSTRUMENT PANEL 219 INSTRUMENT CLUSTER—BASE...
Page 220: Instrument Cluster-Premium
220 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM...
Page 221: Instrument Cluster-Turbo
UNDERSTANDING YOUR INSTRUMENT PANEL 221 INSTRUMENT CLUSTER—TURBO...
Page 222: Instrument Cluster Descriptions
222 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle.
Page 223 5. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. Transmission Range Indicator This display indicator shows the automatic transmission gear selection.
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start.
Page 225 12. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anti-lock brake system.
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
Page 227 17. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 18. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds.
Page 228 228 UNDERSTANDING YOUR INSTRUMENT PANEL turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine.
Page 229: Electronic Vehicle Information Center (Evic)-If Equipped
ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)–If Equipped EVIC Location The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine tem- perature gauge. The EVIC consists of the following: UNDERSTANDING YOUR INSTRUMENT PANEL 229 •...
Page 230 230 UNDERSTANDING YOUR INSTRUMENT PANEL • Left Rear Turn Signal Lamp Out (with a single chime) • Right Front Turn Signal Lamp Out (with a single chime) • Right Rear Turn Signal Lamp Out (with a single chime) • RKE Battery Low (with a single chime) •...
Page 231: Evic Functions
EVIC Functions EVIC Button Press the EVIC button until one of the following func- tions are displayed on the EVIC: • Compass/Temperature/Audio • Average Fuel Economy UNDERSTANDING YOUR INSTRUMENT PANEL 231 • Distance To Empty (DTE) • Elapsed Time • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the resettable function currently being displayed.
Page 232: Average Fuel Economy
232 UNDERSTANDING YOUR INSTRUMENT PANEL For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section. Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET”...
Page 233 Press and release the EVIC button until Personal Settings is displayed in the EVIC. Use the EVIC button to display one of the following choices: Language When in this display you may select different languages for all display nomenclature, including the trip functions. Pressing the EVIC button while in this display selects English, Espanol, Deutsch, Italiano, or Francais depend- ing on availability.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL UNLOCK ALL DOORS is selected all of the doors will unlock at the first press of the remote keyless entry unlock button. Press and hold the EVIC button when in this display until “DRIVER’S DOOR 1ST” or “ALL DOORS”...
Page 235 NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in this section. Delay Power Off to Accessories Until Exit When this feature is selected, the power window switches, radio, hands–free system, DVD video system, power sunroof, and power outlets will remain active for up to 60 minutes after the ignition switch has been turned...
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL North is great enough to cause the compass to give false readings. In order to ensure compass accuracy, the com- pass variance should be properly set according to the compass variance map zone that the vehicle is in. NOTE: Magnetic materials should be kept away from the Instrument Panel.
Page 237 To set the variance: with the ignition in the ON position, with a short button press (less than one seconds) press and release the EVIC button several times until you have displayed the Personal Settings (Customer Program- mable Features) menu. Once in the Personal Settings (Customer Programmable Features) menu, press and release (less than one seconds) the EVIC button several times until “Compass Variance”...
Page 238: Setting The Analog Clock
238 UNDERSTANDING YOUR INSTRUMENT PANEL calibration mode. The Cal indicator will come on con- tinuously in the EVIC display to indicate that the com- pass is now in the calibration mode and that the vehicle can now be driven to calibrate. (A short EVIC button press from the Calibrate Compass (Yes) screen will exit the EVIC Customer Programmable features, and return it to its normal operating mode).
Page 239: Radio General Information
RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent”...
Page 240: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
240 UNDERSTANDING YOUR INSTRUMENT PANEL remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 241 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 243 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will be dis- played. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 244: Operation Instructions - Cd Mode
244 UNDERSTANDING YOUR INSTRUMENT PANEL the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM,12 FM and 12 Satellite (if equipped) stations to be stored into push- button memory.
Page 245 SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD. Press the left side of the button to return to the beginning of the current track, or return to the beginning of the previous track if the CD is within the first 10 seconds of the current selection.
Page 246: Operation Instructions - Auxiliary Mode
246 UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 247: Operating Instructions - Hands Free Phone - If Equipped
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. MUTE will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers.
Page 248: Operating Instructions - Satellite Radio - If Equipped
248 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped Refer to the Satellite Radio section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 249 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 251 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 252 252 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: 16 Digit-Character Dis- Program Type No program type or un- defined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Foreign_Language Information Jazz News...
Page 253 station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station. SET/DIR Button (Radio Mode) —...
Page 254: Operation Instructions - (Cd Mode For Cd Audio Play)
254 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 255: Load/Eject Button (Cd Mode For Cd Audio Play)
to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. MUTE will be displayed. Press the MUTE button a second time and the sound from the speakers will return.
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD after a 2 minute timeout. If the CD is removed and there are no other CD’s in the radio, the radio will remain in CD mode and display INSERT DISC”...
Page 257: Notes On Playing Mp3 Files
Press the RND button a second time to stop Random Play. Buttons 1 - 6 (CD MODE for CD Audio Play) Selects disc positions 1 - 6 for Play/Load/Eject. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited.
Page 258 258 UNDERSTANDING YOUR INSTRUMENT PANEL writing are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files.
Page 259: Operation Instructions
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: •...
Page 260 260 UNDERSTANDING YOUR INSTRUMENT PANEL LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 261: Satellite Radio - If Equipped
AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
Page 262: System Activation
262 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 263: Selecting Satellite Mode In Ref, And Raq, Radios
mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With Navigation Radios Please refer to your Navigation User’s Manual. Selecting Satellite Mode in REF, and RAQ, Radios Selecting Satellite Mode —...
Page 264: Storing And Selecting Pre-Set Channels
264 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 12 AM and 12 FM pre-set stations, you may also commit 12 satellite stations to push button memory.
Page 265: Satellite Antenna
Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna.
Page 266: Radio Operation And Cellular Phones
266 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
Page 267 The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the system in any mode you select.
Page 268 268 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet.
Page 269 Temperature Control Use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red area indicates warmer tempera- tures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con- denser: located in front of the radiator, for an accumula- tion of dirt or insects.
Page 270 270 UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this button to choose be- tween outside air intake or recirculation of the air inside the vehicle. A lamp will illu- minate when you are in recir- culate mode. Only use the re- circulate mode to temporarily block out any outside odors, smoke, or dust and to cool the...
Page 271: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Operating Tips...
Page 272 272 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
Page 273: Rear Window Features
toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. REAR WINDOW FEATURES Electric Rear Window Defroster The push-button is located at the center of the instrument panel, below the radio.
Page 274: Rear Wiper/Washer Switch - If Equipped
274 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch —...
Page 275: Adding Washer Fluid
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Page 277: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 280 Automatic Transaxle ....280 Manual Transaxle .
Page 278 278 STARTING AND OPERATING AutoStick General Information ... . 289 Manual Transaxle Operation ....290 2.4 Liter Turbo— If Equipped ... . . 292 Recommended Shift Speeds .
Page 279 Snow Tires ......320 Tire Rotation Recommendations ... . 321 Fuel Requirements .
Page 280: Starting Procedures
280 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Page 281: Extremely Cold Weather (Below 20°F Or 29°C)
started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 282: After Starting
282 STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time.
Page 283 STARTING AND OPERATING 283 TURBOCHARGER COOL DOWN CHART Driving Conditions Idle Time (in minutes) Before Shut Down Normal Driving Not required. Aggressive Driving or Heavily Loaded Trailer Tow...
Page 284: Automatic Transaxle - If Equipped
284 STARTING AND OPERATING AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 285: Brake/Transmission Interlock System
Brake/Transmission Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the gear selector out of PARK.
Page 286: Gear Ranges For Four Speed Automatic Transaxle
286 STARTING AND OPERATING (N) will continue to operate. This second gear limp-in feature allows the vehicle to be driven to a dealer for service without damaging the transaxle. In the event that the problem has been momentary, the transaxle can be reset to regain all forward gears. Stop the vehicle and shift into Park (P).
Page 287 WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
Page 288 288 STARTING AND OPERATING “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving.
Page 289: Autostick - If Equipped
AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 290: Manual Transaxle Operation
290 STARTING AND OPERATING • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. •...
Page 291 Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in FIRST gear, (not THIRD), when starting from a standing position. Damage to the clutch can result from starting in THIRD. STARTING AND OPERATING 291 For most city driving you will find it easier to use only the lower gears.
Page 292: 2.4 Liter Turbo- If Equipped
292 STARTING AND OPERATING 2.4 Liter Turbo— If Equipped The neutral position of the shift lever is located between THIRD and FOURTH gear. This is the position the shifter lever will return to automatically when neutral is se- lected. When shifting into FIFTH gear, be sure to press the shifter lever all the way to the right to avoid acciden- tally selecting THIRD gear.
Page 293: Downshifting
TABLE 1-MANUAL TRANSAXLE NORMAL ACCELERATION AND CRUISE SHIFT SPEEDS IN mph (km/h) GINE MODE 1 to 2 2 to 3 SIZE Accel 15 (24) 25 (40) 2.4L Turbo Cruise 15 (24) 25 (40) 2.4L Accel 15 (24) 25 (40) Non- Cruise 16 (26) 20 (32) Turbo...
Page 294: Parking Brake
294 STARTING AND OPERATING CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade.
Page 295 NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. Parking Brake Lever When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park.
Page 296: Brake System
296 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. How- ever, the effort required to brake the vehicle will be much greater than that required with the power system oper- ating.
Page 297: Anti-Lock Brake System (Abs) - If Equipped
Anti-Lock Brake System (ABS) — If Equipped The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
Page 298 298 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 299: Power Steering
• and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
Page 300: Traction Control - If Equipped
300 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 301 Traction Control Switch A push-button at the center of the instrument panel, below the radio, turns the Traction Control System ON or OFF. STARTING AND OPERATING 301 The system is always in the “ON” mode unless: • The TRAC OFF switch has been used to turn the system off;...
Page 302: Tire Safety Information
302 STARTING AND OPERATING This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC OFF light.
Page 303 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 304 304 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 305 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 306: Tire Identification Number (Tin)
306 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 307: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 307 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 308 308 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 309 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
Page 310 310 STARTING AND OPERATING...
Page 311: Tires-General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 312: Tire Inflation Pressures
312 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 313 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 314: Radial-Ply Tires
314 STARTING AND OPERATING loading may be required for high speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Page 315: Compact Spare Tire - If Equipped
Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 316: Limited Use Spare - If Equipped
316 STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly.
Page 317: Tread Wear Indicators
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 318: Life Of Tire
318 STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 319: Alignment And Balance
WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 320: Tire Chains
320 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recom- mended.
Page 321: Tire Rotation Recommendations
Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns. These effects can be reduced by timely rotation of tires.
Page 322: Fuel Requirements
322 STARTING AND OPERATING FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87.
Page 323: Reformulated Gasoline
Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
Page 324: Mmt In Gasoline
324 STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
Page 325: Carbon Monoxide Warnings
overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended.
Page 326: Adding Fuel
326 STARTING AND OPERATING the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 327 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
Page 328: Loose Fuel Filler Cap Message
328 STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
Page 329: Vehicle Loading
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. WARNING! • Never add fuel when the engine is running. •...
Page 330: Common Towing Definitions
330 STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
Page 331 WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer.
Page 332: Trailer Hitch Classification
332 STARTING AND OPERATING Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package.
Page 333: Trailer And Tongue Weight
Engine/Transmission Frontal Area 2.4L N/A and 2.4L 20 Sq. Ft Turbo/Automatic* 2.4L N/A and 2.4L 20 Sq. Ft. Turbo/Manual* * N/A (Naturally Aspirated) Refer to local laws for maximum trailer towing speeds. Note 1 – The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
Page 334: Towing Requirements
334 STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. •...
Page 335 CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual.
Page 336 336 STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners.
Page 337 Information section of this manual on Tread Wear Indicators for the proper inspection procedure. − When replacing tires refer to the Tires–General Infor- mation section of this manual on Replacement Tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
Page 338 338 STARTING AND OPERATING WARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance.
Page 339: Towing Tips
7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. STARTING AND OPERATING 339 If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
Page 340: Recreational Towing (Behind Motorhome, Etc.)
340 STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
Page 341 STARTING AND OPERATING 341 If your vehicle is equipped with a manual transaxle, it may be towed with all four wheels on the ground, in a forward direction, at any legal highway speed, for any distance, if the transaxle is in neutral.
Page 343: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....344 If Your Engine Overheats ....344 Jacking And Tire Changing .
Page 344: Hazard Warning Flasher
344 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Warning Switch The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
Page 345 If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe. Turn off the air conditioning and wait until the pointer drops back into the normal range.
Page 346: Jacking And Tire Changing
346 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual.
Page 347: Jack Location
Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. Jack Location Do not attempt to raise this vehicle using a bumper jack. WHAT TO DO IN EMERGENCIES 347 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism.
Page 348: Preparations For Jacking
348 WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire.
Page 349: Jacking Instructions
Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel.
Page 350 350 WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 351: Jump-Starting Procedures Due To A Low Battery
100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free.
Page 352 352 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- axle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 353: Driving On Slippery Surfaces
WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water.
Page 354: Traction
354 WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is danger- ous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.).
Page 355: Towing A Disabled Vehicle
and First gear. Usually the least accelerator pedal pres- sure to maintain the rocking motion without spinning the wheels is most effective. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
Page 356: Without The Ignition Key
356 WHAT TO DO IN EMERGENCIES more than 100 miles (160 km), the vehicle must be towed with the front wheels off the ground to avoid damage to the transaxle. Manual Transaxle Your vehicle may be towed if the gearshift lever is in NEUTRAL.
Page 357: Convertible Top Manual Override
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area.
Page 358 358 WHAT TO DO IN EMERGENCIES Engaging Convertible Top 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely. NOTE: Failure to tighten the bypass screw securely can cause convertible top operating concerns.
Page 359: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Turbo Engine Compartment ... . 362 2.4L Engine Compartment ....363 Onboard Diagnostic System —...
Page 360 360 MAINTAINING YOUR VEHICLE Maintenance-Free Battery ....375 Air Conditioner Maintenance ... . . 377 Power Steering —...
Page 361 Headlight Bulb Replacement ... . . 408 Front Park/Turn Signal/Side Marker Lights . . 409 Front Fog Lights — If Equipped ... 409 Tail/Stop, And Rear Turn Signal Lights .
Page 362: 2.4L Turbo Engine Compartment
362 MAINTAINING YOUR VEHICLE 2.4L TURBO ENGINE COMPARTMENT...
Page 363: 2.4L Engine Compartment
MAINTAINING YOUR VEHICLE 363 2.4L ENGINE COMPARTMENT...
Page 364: Onboard Diagnostic System - Obd Ii
364 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 365: Emissions Inspection And Maintenance Programs
a clicking sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
Page 366: Replacement Parts
366 MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a.
Page 367: Dealer Service
DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 368: Engine Oil
368 MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
Page 369 CAUTION! Overfilling the crankcase as indicated by an oil level above the “Max” mark on the engine oil dipstick will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed.
Page 370 370 MAINTAINING YOUR VEHICLE change your engine oil at every interval shown on schedule “A”—NON TURBO in the maintenance sched- ule section of this manual. If none of these apply to you, and your vehicle is equipped with a Turbo Charged Engine change your engine oil at every interval shown on schedule “A”—TURBO in the maintenance schedule section of this manual.
Page 371 Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recom- mended SAE viscosity grade.
Page 372: Drive Belts - Check Condition And Tension
372 MAINTAINING YOUR VEHICLE Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure.
Page 373 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 374: Engine Timing Belt
374 MAINTAINING YOUR VEHICLE • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Page 375: Maintenance-Free Battery
normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-up- air filter element should be installed during the normal air filter maintenance procedure. WARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
Page 376 376 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 377: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
Page 378: Power Steering - Fluid Check
378 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 379: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors,liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 380: Windshield Washer Reservoir
380 MAINTAINING YOUR VEHICLE 2. Push the release tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place.
Page 381: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged;...
Page 382: Cooling System
382 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Page 383 Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 384 384 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 385 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 386 386 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 387: Hoses And Vacuum/Vapor Harnesses
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 388: Brake System
388 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
Page 389 NOTE: Inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
Page 390 390 MAINTAINING YOUR VEHICLE Brake Fluid Master Cylinder Use only manufacturers recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking.
Page 391: Automatic Transaxle
WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum based fluid to contaminate the brake fluid as seal damage will result! Automatic Transaxle...
Page 392 392 MAINTAINING YOUR VEHICLE Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. Procedure For Checking Fluid Level To properly check the automatic transaxle fluid level, the following procedure must be used:...
Page 393 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. If the fluid is hot, reading should be in the cross hatched area marked “HOT” between the upper two holes in the dipstick. If the fluid is cold, the fluid level should be between the lower two holes, into the area marked “LOW”.
Page 394: Manual Transaxle
394 MAINTAINING YOUR VEHICLE If the transaxle is disassembled for any reason, the fluid and filter should be changed. Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
Page 395: Appearance Care And Protection From Corrosion
Appearance Care And Protection From Corrosion Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 396 396 MAINTAINING YOUR VEHICLE • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
Page 397 oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.
Page 398 398 MAINTAINING YOUR VEHICLE • Oven cleaner • A car wash that uses carbide-tipped wheel cleaning brushes or acidic solutions. CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. NOTE: Replacement costs for components damaged as a result of not following the recommended cleaning practices are considered the responsibility of the cus- tomer.
Page 399 WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
Page 400: Convertible Top Care
400 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 401: General Cleaning
CAUTION! Avoid high pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. Wash in partial shade instead of direct sun.
Page 402: Cloth Top Additional Cleaning Procedure
402 MAINTAINING YOUR VEHICLE Cloth Top Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply Mopar Convertible Cloth Top Cleaner (part number 05012245AA) to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain.
Page 403: Integrated Power Module (Ipm)
INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside of the cover.
Page 404 404 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 Amp Yellow CCN, Power 15 Amp Lt Blue 20 Amp Yellow Ign Run/Acc In- 20 Amp Yellow Pwr run/Acc 10 Amp Red 50 Amp 15 Amp Lt. Blue 10 Amp Red Description Cavity Cartridge 40 Amp...
Page 405 Cavity Cartridge Mini Fuse Fuse 15 Amp Lt. ENG ASD Relay Blue Feed 2 10 Amp Red IGN RUN Only ORC Feed 10 Amp Red IGN RUN ORC/ OCM Feed EMPTY 20 Amp Yellow Heated Seats 10 Amp Red Headlamp Washer Relay Control 30 Amp...
Page 406: Vehicle Storage
406 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 407: Replacement Bulbs
REPLACEMENT BULBS LIGHT BULBS — Inside Center Console Floor Lamp ....T37 Climate Controls ..... . 6233137 Console Gear Selector .
Page 408: Bulb Replacement
408 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2.
Page 409: Front Park/Turn Signal/Side Marker Lights
Front Park/Turn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. MAINTAINING YOUR VEHICLE 409 Front Fog Lights —...
Page 410: Tail/Stop, And Rear Turn Signal Lights
410 MAINTAINING YOUR VEHICLE Tail/Stop, and Rear Turn Signal Lights 1. Remove the screw attaching the tail light housing and remove the housing from the vehicle. 2. Twist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb out of the socket and replace. Back Up Light Bulb 1.
Page 411: Fluids And Capacities
FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil. Cooling System * 2.4 Liter Engines (Mopar Antifreeze/Coolant 5 Year/100,000 Miles Formula), or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. MAINTAINING YOUR VEHICLE 411 U.S.
Page 412: Fluids, Lubricants And Genuine Parts
412 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil.
Page 413: Chassis
Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid. Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Page 415 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..416 Maintenance Schedule ....416 Schedule “B”—All Engines ....419 Schedule “A”—Non Turbo .
Page 416: Emission Control System Maintenance
416 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 417 • Taxi, police, or delivery service (commercial ser- vice).† • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines”...
Page 418 418 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 419: Schedule "B"-All Engines
SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an Change the manual transaxle fluid every 48,000 miles (80...
Page 420 420 SCHEDULE “B”—ALL ENGINES km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the Maintenance Sched- ules section of this manual. If none of these apply to you, and your vehicle is equipped with a Non–Turbo Charged Engine then change your engine oil at every interval shown on schedule “A”—NON TURBO in the maintenance sched- ule section of this manual.
Page 421 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as nec- essary. SCHEDULE “B”—ALL ENGINES 421 3,000 6,000 9,000...
Page 422 422 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the Make-up air filter.
Page 423 Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.†...
Page 424 424 SCHEDULE “B”—ALL ENGINES Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.
Page 425 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals.
Page 426 426 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.†...
Page 427 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 428 428 SCHEDULE “B”—ALL ENGINES * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
Page 429: Schedule "A"-Non Turbo
SCHEDULE “A”—NON TURBO Miles (Kilometers ) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension SCHEDULE “A”—NON TURBO 429 6,000...
Page 430 430 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles.
Page 431 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 432 432 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV valve and replace if necessary. * ‡ Replace the air cleaner filter. Replace the engine timing belt. * Flush and replace the engine coolant at 120 months, if not done at 102,000 miles.
Page 433: Schedule "A"-Turbo
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 434 434 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles. 35,000 40,000 45,000 (56 000) (64 000) (72 000) [42] [48]...
Page 435 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 436 436 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 437 Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 439: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......440 Prepare For The Appointment .
Page 440: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 441 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 442 442 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 443: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 444: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 445: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 446: Temperature Grades
446 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 447 INDEX...
Page 448 448 INDEX ABS (Anti-Lock Brake System) ....297 Adding Engine Coolant (Antifreeze) ..384 Adding Fuel ......326 Adding Washer Fluid .
Page 449 Special Additives ..... . 394 Autostick ......289 Back-Up Lights .
Page 450 450 INDEX Caution, Exhaust Gas ..... 114 CD (Compact Disc) Player ....240,248 CD (Compact Disc) Player Maintenance .
Page 451 Drain, Flush, and Refill ....383 Inspection ......385 Points to Remember .
Page 452 452 INDEX Emergency Deck Lid Release Latch (Convertible) . . 41 Emergency, In Case of Jacking ......346 Jump Starting .
Page 453 Fluid Leaks ......115 Fluid Level Checks Automatic Transaxle ....392 Fluids .
Page 454 454 INDEX Gauges Coolant Temperature ....222 Fuel ....... . 222 Odometer .
Page 455 Instrument Panel and Controls ....218 Instrument Panel Cover ....399 Instrument Panel Lens Cleaning .
Page 456 456 INDEX Dimmer Switch, Headlight ....181 Engine Temperature Warning ....226 Fog ......183,227,409 Front Replacement .
Page 457 Maintenance Schedule Schedule “A”-Non Turbo ....429 Schedule “A”-Turbo ....433 Schedule “B”...
Page 458 458 INDEX Filter ....... 371 Identification Logo ..... 370 Materials Added to .
Page 459 Pregnant Women and Seat Belts ... . 55,89 Preparation for Jacking ....348 Pretensioners Seat Belts .
Page 460 460 INDEX Safety Checks Outside Vehicle ....115 Safety Defects, Reporting ....443 Safety Information, Tire .
Page 461 Security Alarm (Theft Alarm) ....36 Sentry Key (Immobilizer) ....15,37 Sentry Key Programming .
Page 462 462 INDEX Temperature Gauge, Engine Coolant ..222,345 Tether Anchor, Child Restraint ... . 76,109 Theft Alarm (Security Alarm) ....36 Theft System (Security Alarm) .
Page 463 Recreational ......340 Weight ......332 Traction .
Page 464 464 INDEX Uniform Tire Quality Grades ....445 Universal Transmitter ..... 192 Unleaded Gasoline .

This manual is also suitable for:

Cruiser 2006 pt cruiser sedan Pt cruiser convertible 2006 Pt cruiser sedan 2006 Pt cruiser 2006

Chrysler 2006 PT Cruiser Convertible Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2006 PT Cruiser Convertible

Summary of Contents for Chrysler 2006 PT Cruiser Convertible