IBM System x3650 M4 Type 7915 Problem Determination And Service Manual page 7

Installing a PCI riser-card assembly . . . . . . . . . . . . . . . . 219
Removing a PCI adapter from a PCI riser-card assembly . . . . . . . . 221
Installing a PCI adapter in a PCI riser-card assembly . . . . . . . . . 222
Removing the optional dual-port network adapter . . . . . . . . . . . 224
Installing the optional dual-port network adapter . . . . . . . . . . . 225
Removing an optional ServeRAID upgrade adapter . . . . . . . . . . 229
Installing an optional ServeRAID upgrade adapter . . . . . . . . . . 230
Removing a remotely installed ServeRAID adapter battery . . . . . . . 231
Installing a ServeRAID SAS controller battery on the remote battery tray
Removing a ServeRAID SAS controller battery holder . . . . . . . . . 235
Installing a ServeRAID SAS controller battery holder
Removing a hot-swap hard disk drive . . . . . . . . . . . . . . . 236
Installing a hot-swap hard disk drive
Removing a simple-swap hard disk drive . . . . . . . . . . . . . . 238
Installing a simple-swap hard disk drive . . . . . . . . . . . . . . 238
Removing the SAS hard disk drive backplane . . . . . . . . . . . . 240
Installing the SAS hard disk drive backplane
Removing the simple-swap hard disk drive backplate . . . . . . . . . 242
Installing the simple-swap hard disk drive backplate . . . . . . . . . . 242
Removing an optional CD-RW/DVD drive. . . . . . . . . . . . . . 244
Installing an optional CD-RW/DVD drive . . . . . . . . . . . . . . 245
Removing the DVD drive cable . . . . . . . . . . . . . . . . . 245
Installing the DVD drive cable . . . . . . . . . . . . . . . . . . 246
Removing an optional tape drive . . . . . . . . . . . . . . . . . 247
Installing an optional tape drive . . . . . . . . . . . . . . . . . 249
Removing a memory module (DIMM) . . . . . . . . . . . . . . . 250
Installing a memory module . . . . . . . . . . . . . . . . . . . 250
Installing a DIMM . . . . . . . . . . . . . . . . . . . . . . 256
Removing a hot-swap dual-motor hot-swap fan
Installing a hot-swap dual-motor hot-swap fan . . . . . . . . . . . . 258
Removing a hot-swap ac power supply
Installing a hot-swap ac power supply . . . . . . . . . . . . . . . 259
Removing a hot-swap dc power supply
Installing a hot-swap dc power supply . . . . . . . . . . . . . . . 266
Removing an optional remotely installed ServeRAID adapter battery . . . . 271
Installing an optional ServeRAID SAS controller battery on the remote
battery holder . . . . . . . . . . . . . . . . . . . . . . . 272
Removing the battery . . . . . . . . . . . . . . . . . . . . . 273
Installing the battery . . . . . . . . . . . . . . . . . . . . . 275
Removing the operator information panel assembly . . . . . . . . . . 277
Installing the operator information panel assembly . . . . . . . . . . 278
Removing and replacing Tier 2 CRUs . . . . . . . . . . . . . . . . 278
Removing a microprocessor and heat sink . . . . . . . . . . . . . 279
Installing a microprocessor and heat sink . . . . . . . . . . . . . . 282
Thermal grease . . . . . . . . . . . . . . . . . . . . . . . 287
Removing a heat-sink retention module . . . . . . . . . . . . . . 289
Installing a heat-sink retention module . . . . . . . . . . . . . . . 289
Removing the system board
Installing the system board . . . . . . . . . . . . . . . . . . . 292
Chapter 6. Configuration information and instructions
Updating the firmware . . . . . . . . . . . . . . . . . . . . . . 297
Configuring the server . . . . . . . . . . . . . . . . . . . . . . 298
Using the ServerGuide Setup and Installation CD. . . . . . . . . . . 299
Using the Setup utility . . . . . . . . . . . . . . . . . . . . . 301
Using the Boot Manager program
. . . . . . . . . . . . . . . 237
. . . . . . . . . . . . 240
. . . . . . . . . . . 257
. . . . . . . . . . . . . . 259
. . . . . . . . . . . . . . 262
. . . . . . . . . . . . . . . . . . 290
. . . . . . . . . . . . . . . . 306
. . . . . . . . . 235
. . . . . . . . 297
Contents
232
v