Table of Contents
Advertisement
ICDM-RX/TCP Installation and Configuration Guide
Configuring the Network Settings (PortVision DX)
11. Select the Pepperl+Fuchs ICDM-RX, ICE2, ICE3 or ICRL-M Ethernet attached products that you want to
locate and then click Scan.
Note: If the Pepperl+Fuchs ICDM-RX, ICE2, ICE3 or ICRL-M Ethernet attached product is not on the local
segment and it has been programmed with an IP address, it will be necessary to manually add the
Pepperl+Fuchs ICDM-RX, ICE2, ICE3 or ICRL-M Ethernet attached product to PortVision DX.
Refer to the PortVision DX for the procedure to manually add an ICDM-RX/TCP.
12. Go to Step 6 in the next section, Configuring the Network Settings (PortVision DX) on Page 28, to program
the ICDM-RX/TCP network settings.
You can customize how PortVision DX displays the devices, refer to the help system for specific procedures.
•
Create sessions tailored for specific audiences using the New Session and Import Session options.
•
Sort by Device Name, Model, IP Address, MAC Address, Software Version or Status by clicking in the
column heading to find devices faster.
•
To create a spreadsheet of the information, use the Export Device List to Notepad option and then import
it into your favorite spreadsheet. The text file is tab delimited.
•
Organize all of your devices in logical folders as shown below.
•
Add shortcuts to other applications using Tools > Applications > Customize feature.
3.5. Configuring the Network Settings (PortVision DX)
Use the following procedure to change the default network settings on the ICDM-RX/TCP for your network
using PortVision DX. The default network settings are:
•
IP address: 192.168.250.250
•
Subnet mask: 255.255.0.0
•
Gateway address: 192.168.250.1
Note: Technical Support advises configuring one new ICDM-RX/TCP at a time to avoid device driver
configuration problems. If you want to configure multiple ICDM-RX/TCPs using the Assign IP to
Multiple Devices option, see Configuring Multiple ICDM-RX/TCPs Network Addresses on Page 90.
The following procedure shows how to configure a single ICDM-RX/TCP connected to the same network
segment as the Windows system. If the ICDM-RX/TCP is not on the same physical segment, you can add it
manually using Adding a New Device in PortVision DX on Page 90.
1. If you have not done so, install PortVision DX (Installing PortVision DX on Page 27).
2. Start PortVision DX using the PortVision DX desktop shortcut or from the Start button, click
Pepperl+Fuchs Comtrol > PortVision DX.
3. Depending on your operating system, you may need to click Yes to the Do you want to allow the following
program to make changes to this computer? query.
4. Click the Scan button in the Toolbar.
5. Click Scan to locate the Pepperl+Fuchs ICDM-RX, ICE2, ICE3 or ICRL-M Ethernet attached products
including the ICDM-RX/TCP on the network.
Note: If you do not have any RocketLinx managed switches or IO-Link master (ICE2/ICE3)s, it saves
scanning time if you do not scan for them.
If PortVision DX does not locate your ICDM-RX/TCP on the network, make sure that you are using
the latest version of PortVision DX: https://www.pepperl-fuchs.com.
6. Right-click the ICDM-RX/TCP and select Properties in the pop up menu.
7. Optionally, rename the ICDM-RX/TCP in the Device Name field.
Note: The MAC address, Serial Number and Device Status fields are automatically populated and you
cannot change those values.
8. Optionally, enter the serial number, which is on a label on the ICDM-RX/TCP.
28
Advertisement
Table of Contents
Troubleshooting
