Table of Contents
Advertisement
ICDM-RX/TCP Installation and Configuration Guide
ICDM-RX/TCP-4DB9/2RJ45-PM Installation
2.7. ICDM-RX/TCP-4DB9/2RJ45-PM Installation
Use the following procedure to install the ICDM-RX/TCP-4DB9/2RJ45-PM.
1. Optionally, attach the mounting brackets using the screws provided in the kit (6-32 1/4" flathead machine) or
place the ICDM-RX/TCP-4DB9/2RJ45-PM on a stable surface.
Failure to use the correct screws can damage the PCB and void the warranty. Do NOT use
screws that exceed the length of the screws provided with the mounting bracket kit.
Note: If you ordered the ICDM-RX/TCP Rackmount Shelf Kit accessory, use the document that
accompanied that kit to mount the ICDM-RX/TCP-4DB9/2RJ45-PM on the shelf.
Note: Do not connect multiple units until you have changed the default IP address, see Initial Configuration on
Page 26.
2. Connect the ICDM-RX/TCP-4DB9/2RJ45-PM to the same Ethernet network segment as the host PC. The
Ethernet port are interchangeable so you can connect either the UP or DOWN port. You can refer to Daisy-
Chaining ICDM-RX/TCP With Dual Ethernet Ports on Page 147 for more information.
3. Apply power to the ICDM-RX/TCP-4DB9/2RJ45-PM by connecting the AC power adapter to the ICDM-RX/
TCP-4DB9/2RJ45-PM, the appropriate power cord for your location to the power adapter, and plugging the
power cord into a power source. If you want to provide a power supply, see ICDM-RX/TCP-4DB9/2RJ45-
PM Power Supply on Page 125.
Note: Use a UL listed power supply with an output rating of 24 V DC with 12 Watts output minimum to
power up the ICDM-RX/TCP (unit marked LPS). Alternate – Listed/CN, ITE Power Supply, input
rated 100-240 V AC, 0.33 A minimum; output rated 24 V DC, 0.5 A minimum. Unit marked "LPS."
4. Verify that the PWR LED has completed the boot cycle and the network connection for the ICDM-RX/TCP-
4DB9/2RJ45-PM is functioning properly.
PWR LED on the front panel of the ICDM-RX/TCP-4DB9/2RJ45-PM is lit, indicating you have
power and it has completed the boot cycle.
PWR
The PWR LED flashes while booting and it takes approximately 15 seconds for the Bootloader to
complete the cycle. When the Bootloader completes the cycle, the LED has a solid, steady light
that blinks approximately every 10 seconds.
LNK
The red LNK ACT LED is lit, indicating that you have a
ACT
working Ethernet connection.
COL
If the red COL LED is lit, there is a network collision.
If the red 100 LED is lit, it indicates a working 100 MB
100
Ethernet connection (100 MB network, only). If the LED is not
lit, it indicates a 10 MB Ethernet connection.
Note: For additional LED information, go to the Status LED table on Page 148.
Do not connect RS-422/485 devices until the IP address is configured and an appropriate
port interface type has been configured. The default port setting is RS-232.
5. Go to Initial Configuration on Page 26 to configure the ICDM-RX/TCP-4DB9/2RJ45-PM for use.
ICDM-RX/TCP-4DB9/2RJ45-PM LED Descriptions
10/100 NETWORK
LNK
ACT
COL
100
UP
DOWN
21
Advertisement
Table of Contents
Troubleshooting
