evertz 8010-SIE Instruction Manual page 9

3.8. PROGRAMMING THE ENGINEERING SETUP FUNCTIONS..........................................3-18
3.8.1. Selecting the Video Type .......................................................................................3-20
3.8.2. Adjusting the Output Level of the LTC Generator ..................................................3-20
3.8.3. Setting The VITC Deleter Line Range....................................................................3-20
3.8.4. Selecting the Colour Frame Phase ........................................................................3-21
3.8.5. Selecting the Generator Framing Reference..........................................................3-21
3.8.6. Turning on the Daylight Saving Time Compensation (8010-SIE-GPS II ONLY) ....3-22
3.8.7. Configuring The General Purpose Inputs and Outputs ..........................................3-22
3.8.7.1. Assigning the Functions of the General Purpose Inputs .........................3-22
3.8.7.2. Assigning the Functions of the General Purpose Outputs.......................3-23
3.8.7.3. Adjusting the General Purpose Output Duration .....................................3-24
3.8.7.4. Setting the Time of the Event Registers ..................................................3-25
3.8.8. Configuring The Serial Port ....................................................................................3-25
3.8.8.1. Selecting the Serial Port Baud Rate ........................................................3-25
3.8.8.2. Testing the Serial Port .............................................................................3-25
3.8.8.3. Setting the Serial Port Mode....................................................................3-26
3.8.9. Adjusting the Front Panel Display Brightness ........................................................3-26
3.8.10. Turning off the SDI Characters When The Program Source is 'ON AIR' (8010-SIE Only)
...............................................................................................................................3-26
3.8.11. Setting the LVS address (8010-SIE Only)..............................................................3-26
3.8.12. Setting the SDI Vertical Interval Blanking...............................................................3-27
3.8.13. Setting the NTSC Setup Pedestal on the Monitor Analog Output ..........................3-27
3.8.14. Downloading New Character Fonts........................................................................3-27
3.8.15. Testing the RAM.....................................................................................................3-27
3.8.16. Resetting the 8010-SIE to Factory Defaults ...........................................................3-28
3.8.17. Displaying the 8010-SIE Software version .............................................................3-28
3.9. GLOBAL POSITION SYSTEM OPERATION (MODEL 8010-SIE-GPS II ONLY).............3-28
3.9.1. Setting the GPS Time Reference Mode .................................................................3-28
3.9.2. Displaying the Receiver's UTC Time......................................................................3-29
3.9.3. Controlling the Synchronization Accuracy to the GPS Based Time .......................3-29
3.9.4. Setting the Time Each Day when the 8010-SIE-GPS II will Synchronize to the GPS
time. .......................................................................................................................3-30
3.9.5. Entering the Time Zone Offset ...............................................................................3-30
4. SERIAL REMOTE CONTROL PROTOCOL ................................................................................4-1
4.1. VTR MODE - COMMUNICATING WITH A VTR..................................................................4-1
4.1.1. Data Format .............................................................................................................4-1
4.1.2. Communications Protocol ........................................................................................4-1
4.1.3. Message Block Format.............................................................................................4-2
4.1.4. Commands Supported .............................................................................................4-3
4.1.5. Time Code Sense Command ...................................................................................4-3
4.1.6. Status Sense Command ..........................................................................................4-4
4.2. LVS MODE - COMMUNICATING WITH A PROFILE DISK RECORDER ..........................4-4
4.2.1. Data Format .............................................................................................................4-4
4.2.2. Message Block Format.............................................................................................4-4
4.2.3. Command Processing ..............................................................................................4-5
Model 8010-SIE Digital Source ID Encoder Manual
Revision 2.2