Table of Contents
Advertisement
Quick Links
1.
OVERVIEW......................................................................................................................................... 1
2.
INSTALLATION.................................................................................................................................. 4
2.1. VIDEO CONNECTIONS ............................................................................................................ 4
2.1.1.
7710XUDC-AES4-HD ................................................................................................. 5
2.2. GENLOCK REFERENCE .......................................................................................................... 5
2.4. AES INPUT AND OUTPUT AUDIO CONNECTIONS ("-AES4" VERSIONS ONLY) ............... 6
2.5. GENERAL PURPOSE INPUTS AND OUTPUTS ...................................................................... 8
3.
SPECIFICATIONS.............................................................................................................................. 9
3.1. SERIAL DIGITAL VIDEO INPUTS ............................................................................................ 9
3.1. SERIAL DIGITAL VIDEO OUTPUTS ........................................................................................ 9
3.2. ANALOG COMPOSITE VIDEO OUTPUT ................................................................................. 9
3.3. GENLOCK INPUT ................................................................................................................... 10
3.5. LTC INPUT .............................................................................................................................. 10
3.6. LTC OUTPUT .......................................................................................................................... 10
3.7. AES AUDIO INPUTS ............................................................................................................... 10
3.8. AES AUDIO OUTPUTS ........................................................................................................... 10
3.9. GENERAL PURPOSE INPUTS AND OUTPUTS .................................................................... 11
3.10. ELECTRICAL .......................................................................................................................... 11
3.11. PHYSICAL ............................................................................................................................... 11
7710XUC-HD HD Format Up/Down/Cross Converter
TABLE OF CONTENTS
).................................................................................. 5
Revision 1.0
7700 MultiFrame Manual
Advertisement
Table of Contents
Related Manuals for evertz 7700
Summary of Contents for evertz 7700
-
Page 1: Table Of Contents
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter TABLE OF CONTENTS OVERVIEW............................1 INSTALLATION..........................4 2.1. VIDEO CONNECTIONS ......................4 2.1.1. 7710XUDC-AES4-HD ....................5 2.2. GENLOCK REFERENCE ......................5 2.3. TIME CODE (7710XUC-AES4-HD O ).................. 5 2.4. AES INPUT AND OUTPUT AUDIO CONNECTIONS (“-AES4” VERSIONS ONLY) ....6 2.5. - Page 2 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter STATUS INDICATORS ........................11 4.1. AUDIO STATUS LED ......................13 CARD EDGE CONTROLS ....................... 13 5.1. SETTING THE OUTPUT VIDEO FRAME RATE ..............14 5.2. SETTING THE OUTPUT VIDEO STANDARD ................ 15 ON-SCREEN MENUS ........................
- Page 3 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.5. CONFIGURING THE DE-INTERLACER ................. 30 6.5.1. Setting the De-interlacer Mode.................. 30 6.5.2. Setting the Freeze Frame Threshold................. 30 6.5.3. Setting the Motion Detection Controls............... 31 6.5.4. Setting the Interfield Weighting Factor ..............31 6.6.
- Page 4 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.11. CONFIGURING THE ANALOG VIDEO OUTPUT PARAMETERS ......... 42 6.11.1. Adding the NTSC Setup Pedestal ................43 6.11.2. Colour Bars ....................... 43 6.11.3. Setting the Composite Display Mode – Colour or Monochrome........ 43 6.11.4.
- Page 5 Tables Table 1: AES Audio Connector Pinout ........................ 6 Table 2: AES Audio Breakout Cable (Evertz Part # WA-1XY-R) ................ 7 Table 3: AES Audio Breakout Cable (Evertz Part # WPAES8-BNCM-6F) ............7 Table 4: Audio Group Status LEDs ........................13 Table 5: AES Input Status LEDs ........................
- Page 6 Jul 06 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either express or implied.
-
Page 7: Overview
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter OVERVIEW The 7710XUC series of products is designed to solve the problems of adapting to different SD and HD formats, while also offering high quality up-, cross-, and down-conversion. There is an input BNC, an output BNC, an output BNC with an on-screen display, and a BNC that can be configured as either an input or an output. - Page 8 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter All the modules accept two groups of embedded audio on the input and re-embed them into the serial video outputs. The “-AES4” versions also accept four external discrete unbalanced AES inputs and provide four AES outputs with the same audio that is being embedded.
-
Page 9: Figure 1: 7710Xuc-Hd And 7710Xuc-Aes4-Hd Block Diagram
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Composite 4 AES Analog AES Rx Inputs -AES4 only Audio & Audio Processing 4 AES Metadata Metadata & Audio Outputs Formatter Extractor Delay HD/SD -AES4 only Input EQ & Audio Present Optional... -
Page 10: Installation
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter INSTALLATION The 7710XUC-HD and 7710XUC-AES4-HD modules come with a companion rear plate that occupies two slots in the frame. The 7710XUDC-AES4-HD also comes with a companion rear plate that occupies three slots in the frame. For information on mounting the rear plate and inserting the module into the frame see the 7700FR chapter section 3. -
Page 11: 7710Xudc-Aes4-Hd
On older versions of the 7710XUDC-AES4-HD, there was an AUX SDI IN instead of a 6Hz IN. The AUX SDI IN does not have any functionality. If 6Hz IN support is required, the module needs to be returned to the Evertz facility for modifications. 2.3. -
Page 12: Aes Input And Output Audio Connections ("-Aes4" Versions Only)
Both the 7710XUC-AES4-HD and 7710XUDC-AES4-HD are shipped with a breakout cable for the 15 pin D connector (Evertz Part # WA-1XY-R or WPAES8-BNCM-6F), which can be used to facilitate wiring the audio and GPI connections. The pinout of the cables are shown in Table 2 and Table 3. -
Page 13: Table 2: Aes Audio Breakout Cable (Evertz Part # Wa-1Xy-R)
AES In 4 Coax Soldered to Shell AES A3 BNC MALE AES In 3 AES In 3 Shell Black WIRE Table 2: AES Audio Breakout Cable (Evertz Part # WA-1XY-R) High Density 7710XUC- 7710XUDC- DB-15 AES4-HD AES4-HD Ground/Shield Connector Connection... -
Page 14: General Purpose Inputs And Outputs
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 2.5. GENERAL PURPOSE INPUTS AND OUTPUTS On all versions of the module, a 6-pin connector labeled GPIO contains four GPI/O inputs. + 12 3.6 K internal circuit Command Figure 4: GPI Input Circuitry The GPO is active low with internal pull up (10k Ohm) resistors to +5 V. -
Page 15: Specifications
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter SPECIFICATIONS 3.1. SERIAL DIGITAL VIDEO INPUTS Standards: 270Mb/sec SMPTE 259M or 1.485 Gb/sec SMPTE 292M – menu selectable. SMPTE 260M, SMPTE 274M, SMPTE 296M, SMPTE 349M Number of Inputs: 1 or 2 (optional based on PGM IN/OUT configuration) -
Page 16: Genlock Input
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 3.3. GENLOCK INPUT Type: HD Tri-Level sync, NTSC or PAL Colour Black 1 V p-p Connector: BNC per IEC 60169-8 Amendment 2 Termination: 75 ohm (jumper selectable) 3.4. 6Hz INPUT Standard: 6Hz TTL Pulse Number of Inputs: 1 (only on “-AES4”... -
Page 17: General Purpose Inputs And Outputs
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 3.9. GENERAL PURPOSE INPUTS AND OUTPUTS Number: 4 (configurable as inputs or outputs) Type: Opto-isolated, active low with internal pull-ups to +5 or +12V (jumper settable) Connector: 6 pin removable terminal block... -
Page 18: Figure 7: Led Status Indicators: "-Aes4" Versions
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter SUBMODULE VIDEO LOCKED 1 2 3 4 5 6 7 8 MODULE AES Inputs VIDEO push PRESENT toggle button switch 7710XUDC-AES4-HD LOCAL GENLOCK FAULT Audio Group Figure 7: LED Status Indicators: “-AES4” Versions... -
Page 19: Audio Status Leds
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 4.1. AUDIO STATUS LEDS Four LEDs located on the main board on the lower end of the module (near the card extractor) indicate which audio groups are present in the input video. Audio group LED 1 is located closest to the center of the module. -
Page 20: Setting The Output Video Frame Rate
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter The off (open) position is up, or farthest from the printed circuit board. There is also a toggle switch and pushbutton which are used to navigate the on screen menu (see section 0). -
Page 21: Setting The Output Video Standard
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 5.2. SETTING THE OUTPUT VIDEO STANDARD DIP switches 1 to 5 set the output video standard. DIP switches 6 and 7 set the exact frame rate. For example to select 1080i/59.94 as the output format set switches 6 and 7 to the on and off position (select 59.94) and set switches 1 to 5 to the off position. -
Page 22: On Screen Display - Main Menu
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter On all menus, there are two other selectable items: Back and Exit. Selecting Back will take you to the previous menu (the one that was used to access the current menu) while Exit will return the display to its normal operating mode. - Page 23 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Sets the frame rate, input and output video standards, pull down references, Video caption blanking, action on loss of input, timing reference select, and timing offset for the video output Configuration of the main output picture aspect ratio presets. Configuration...
-
Page 24: Configuring The Video Controls
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3. CONFIGURING THE VIDEO CONTROLS The Video menus are used to configure parameters associated with the input and output video standards and output video timing. The chart below shows the items available in the Video menu. Sections 6.3.1 to 6.3.14 provide detailed information about each of the menu items. -
Page 25: Setting The Input Video Standard
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3.2. Setting the Input Video Standard Video This control selects the input video standard being used. The choice of input standards available depends on the Frame Rate menu setting. For Input Standard example, to select 1080i/59.94 as the output format, set the Frame Rate... -
Page 26: Select The Video Mode On Pgm Out/In
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3.5. Select the Video Mode on PGM OUT/IN Video This control determines the whether the PGM OUT/IN BNC will be used as PGM OUT/IN Mode an input or output. Video Output Video Input When it is set to Video Output, the PGM OUT/IN BNC is used as a second output with the same content as is available on the PGM OUT BNC. -
Page 27: Selecting The 3:2 Pulldown Reference With 1080P/23.98Sf Input Video
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3.7. Selecting the 3:2 Pulldown Reference with 1080p/23.98sF Input Video This menu setting is only used when converting from a 23.98 Hz frame rate to a 59.94 Hz field or frame rate, or when converting from a 59.94 Hz field or frame rate to a 23.98 Hz frame rate. -
Page 28: Figure 8: 3:2 Pulldown Sequence Insertion - 1080P/23.98Sf Input Video
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Video This control allows the user to select other frames as the A Frame. A Frame Offset Figure 9 shows how this control defines the A frame candidate when the 6 Hz pulse is present. Figure 10 shows how this control defines the A frame when RP188 Ancillary data is used to control the 3:2 pulldown. -
Page 29: Blanking Line 21 Captions For Sd Video Inputs
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 1080p/ 23.98sF A Frame Candidate A Frame Offset Figure 10: RP188 Pulldown Sequence A Frame Alignment – 1080p/23.98sF Input Video 6.3.9. Blanking Line 21 Captions for SD Video Inputs This menu setting is only used when the input video is 525i/59.94. It is not applicable in any other input video formats. -
Page 30: Setting The Source Of Time Code
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3.12. Setting the source of Time Code Video This control selects the time code source: Embedded or External LTC input (if available). Time Code Source Embedded Select embedded to use RP188 ancillary time code (ATC) as the source for... -
Page 31: Calculating The Delay Through The Format Translator/Cross Converter
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter If the frame rate of the module is set to 50Hz, then only 1080i/50 or 625i/50 will be recognized as valid Genlock. 6.3.14.2. Calculating the Delay through the Format Translator/Cross Converter. The delay through the Format Translator/Cross Converter is dependent on the video input format, the Format Translator/Cross Converter processing mode, and the V Phase and H Phase Offset settings. -
Page 32: Setting The Horizontal Phase Of The Output Video
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.3.14.5. Setting the Horizontal Phase of the Output Video Video With this control, you can set the horizontal timing of the output video with respect to the reference input set by the Reference Select menu item. -
Page 33: Setting The Scaler Filter Sharpness
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter H Filter Cutoff Sets the type of the horizontal filter in the scaler V Filter Cutoff Sets the type of the vertical filter in the scaler Selects the aspect ratio conversion to be performed... -
Page 34: Setting The Aspect Ratio Of The Output Picture
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.4.2. Setting the Aspect Ratio of the Output Picture The Aspect Ratio menu sets the user image conversion parameters to pre-defined values. Once selected, the user can fine-adjust the picture parameters via the input and output H and V start and stop menus. -
Page 35: Set The Colour Of The Letterbox Panels
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.4.3. Set the Colour of the Letterbox Panels. There are three menu items used to set the panel colour. The menu item for each colour component works in the same way, so for the sake of brevity, only the menu item for the Red component will be included in this manual. -
Page 36: Configuring The De-Interlacer
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.5. CONFIGURING THE DE-INTERLACER The De-interlacer menus are used to configure parameters associated with the de-interlacer hardware. The chart below shows the items available in the De-interlacer menu. Sections 6.5.1 to 6.5.4 give detailed information about each of the menu items. -
Page 37: Setting The Motion Detection Controls
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.5.3. Setting the Motion Detection Controls De-interlacer With this control, you can change the threshold of what is deemed motion by the de-interlacer. Motion Detection Threshold 0 to 15 6.5.4. Setting the Interfield Weighting Factor De-interlacer With this control, you can set the Interfield Weighting Factor control. -
Page 38: Enabling Rgb Clipper
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter All of these parameters affect the video in real-time. H&V frequency bands will cause hits to the video while a new filter is loaded. 6.6.1. Enabling RGB Clipper Proc Func This enables the RGB clipper. When enabled, the module will clip any RGB Clip illegal levels of R, G, and B (individually) to black and white levels. -
Page 39: Setting The Hue
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.6.5. Setting the Hue Proc Func With this control, the user can adjust the Hue or color of components +/- 30 degrees in 0.1 degree steps. -30 to 30 6.6.6. Setting the Gamma Level Proc Func With this control, the user can adjust the Gamma correction factor. -
Page 40: Setting The Vertical Intensity
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.6.11. Setting the Vertical Intensity Proc Func Selects the intensity of the vertical enhancement process, as a percentage of the horizontal enhancement. Vertical Intensity 100% The range is 0 to 100% in steps of 25%, where 0% refers to no vertical... -
Page 41: Turning On The Noise Reduction
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.7.1. Turning on the Noise Reduction Noise Reducer This menu item controls the various levels of noise reduction to apply to the video signal. The different levels will set the motion detection threshold and Noise Reduction the aggressiveness of the filters to remove noise. -
Page 42: Configuring The Audio Settings
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.8. CONFIGURING THE AUDIO SETTINGS The SMPTE 272M and 299M standards permit up to four groups of four audio channels to be embedded into the serial digital video bitstream. The card de-embeds two groups of audio from the serial digital input video, and uses them as the source for re-embedding on the serial digital output video. -
Page 43: Selecting The Audio Groups Destined For The De-Embedders
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.8.1. Selecting The Audio Groups Destined for the De-embedders The module has two de-embedders that will de-embed one group of audio from the serial digital video input. There is one set of controls for each de-embedder. For the sake of brevity, only one control will be included in this manual. -
Page 44: Configuring The Audio Source For Input Channel 1 And 2
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.8.5. Configuring the Audio Source for Input Channel 1 and 2 Audio Settings This control allows the user to configure the source for input channels 1 and 2 of the sample rate converters. -
Page 45: Configuring The Audio Processing Functions
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.9. CONFIGURING THE AUDIO PROCESSING FUNCTIONS The Audio Proc Embedded and Audio Proc External menus are used to configure parameters associated with the audio processing functions of the 7710XUC-AES4-HD modules. The chart below shows the items available in the Audio Proc menus. -
Page 46: Configuring The Output Audio Channel Sources
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.9.1. Configuring the Output Audio Channel Sources There are eight controls that select the source of the eight audio channels being processed. For the sake of brevity, only the selection control for channel 1 will be included in this manual. -
Page 47: Configuring Closed Captioning
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.10. CONFIGURING CLOSED CAPTIONING The 7710XUC series handles closed captioning transparently. The modules will transcode any captions in the input SD video signal to the output HD signal The Closed Captioning menus are used to configure parameters associated with the closed caption handling. -
Page 48: Setting The Hd Write Line
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.10.2. Setting the HD Write Line Closed Captioning This parameter will set the HD line where the HD VANC captions are inserted on the output HD video as per SMPTE 334M. HD Write Line... -
Page 49: Adding The Ntsc Setup Pedestal
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter NTSC setup Selects whether the NTSC 7.5 IRE pedestal will be added to the composite pedestal analog output video Colour Bars Turns on internally generated colour bar test signal Composite display Selection of colour or B/W modes... -
Page 50: Setting The Video Level
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.11.4. Setting the Video Level Composite Output This control allows the user to adjust the output level of the analog video (including sync). When set to 0, the nominal output video level will be 140 IRE. -
Page 51: Setting The Chroma Filter Bandwidth
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.11.10. Setting the Chroma Filter Bandwidth Composite Output The Cb and Cr channels may be filtered with any of these bandwidths. Chroma Filter Selection 650kHz, 1.0Mhz, 1.3MHz, 2.0MHz, 3.0MHz 6.12. UTILITIES The Utilities menus are used to list the module firmware version, upgrade the firmware, and manage the user presets. -
Page 52: Recalling Configurations From The User Presets
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter There will be a slight disturbance in the operation of the card and the on-screen display while the new preset is being recalled. 6.12.1.1. Recalling Configurations from the User Presets Utilities This control is used to initiate a recall of the current card configuration from Load Preset one of the user presets. -
Page 53: Storing Configurations From The User Presets
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.12.1.2. Storing Configurations from the User Presets Utilities This control is used to initiate a store of the current card configuration into one of the user presets. Store Preset Cancel Use the toggle switch to select the preset location where you want to store 1 to 10 the module configuration. -
Page 54: Setting The Function Of Gpi 4 (7710Xuc-Hd Only)
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 6.12.4. Setting the Function of GPI 4 (7710XUC-HD only) Utilities On the 7710XUC-HD, the user can configure the function of GPI 4. The GPI can be set to recall presets or as a 6Hz source for 3:2 pulldown. -
Page 55: Jumpers
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter JUMPERS EVERTZ (D) 7710FT +5V +12V MODULE STATUS GPI LEVEL SIGNAL PRESENT GENLOCK Upgrade FRAME STATUS REF TERM SFF POWER +12V Figure 11: Location of Jumpers – Rev D Main Module On most Rev D Main Modules, the jumper J7 has been replaced by a slide switch on the bottom of the module for easy access. -
Page 56: Selecting Whether Local Faults Will Be Monitored By The Global Frame Status
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter EVERTZ (C) A7710XDC MODULE STATUS SIGNAL PRESENT SDI OUT/ Composite SDI OUT/ Composite +5V +12V GPI LEVEL SFF POWER +12V Figure 13: Location of Jumpers – Sub Module for 7710XUDC-AES4-HD 7.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED... -
Page 57: Selecting Whether The Genlock Reference Input Is Terminated
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter To upgrade the firmware in the module unit: 1. Pull the module out of the frame. 2. Move Jumper J7 into the UPGRADE position. 3. Install the Upgrade cable provided (located in the vinyl pouch in the front of this manual) onto header J2 at the card edge. -
Page 58: Selecting Composite Or Sdi Output
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter + 12 3.6K internal circuit Command Figure 14: Setting the GPI Input Pullup Voltage 7.5. SELECTING COMPOSITE OR SDI OUTPUT The 7710XUDC sub-module can output either analog composite video or SDI via jumper selections J25 and J26 illustrated in Figure 13: Location of Jumpers –... -
Page 59: Selecting Gpi 4 For 6Hz Source (7710Xuc-Hd Only)
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 7.6. SELECTING GPI 4 for 6HZ SOURCE (7710XUC-HD Only) The 7710XUC-HD module can set the functionality of GPI 4 (see section 6.12.4). However, the user will also have to change a jumper on the Rear I/O plate to ensure proper functionality. The location of the jumper shown in Figure 15 will configure the Rear I/O. -
Page 60: Vistalink™ Remote Monitoring/Control
2. Managed devices (such as 7710XUC-HD), each with a unique address (OID), communicate with the NMS through an SNMP Agent. Evertz VistaLINK™ enabled 7700 series modules reside in the 3RU 7700FR-C MultiFrame and communicate with the manager via the 7700FC VistaLINK™ frame controller module, which serves as the Agent. -
Page 61: Vistalink
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 8.2. VISTALINK MONITORED PARAMETERS The following parameters can be remotely monitored through the VistaLINK™ interface. Parameter Description Indicates the presence of a valid video input signal on the PGM IN Input Video Present... -
Page 62: Vista Link Tm Controlled Parameters
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter 8.3. VISTALINK CONTROLLED PARAMETERS Parameter Description Video Frame Rate Select the video input frame rate Video Standard Input Selects the video input standard. Video Standard Output Selects the video output standard. Video Input Source... - Page 63 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Detail Gain Sets the level for the detail gain H Filter Cutoff DC Sets the type of the horizontal filter in the scaler V Filter Cutoff DC Sets the type of the vertical filter in the scaler...
- Page 64 7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Input Ch 7&8 Source Sets the source for input channel 7 and 8 of the SRC Embedder A DC Sets the audio group destination for embedder A Embedder B DC Sets the audio group destination for embedder B...
-
Page 65: Vista Link Tm Traps
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter Video level Controls the output video level Controls the output video hue H blanking Controls the width of horizontal blanking VBI processing Either pass or blank the vertical blanking interval lines Y Filter Selection Standard composite filtering or adjustable filtering is selectable Wideband Frequency. -
Page 66: Menu Quick Reference
7700 MultiFrame Manual 7710XUC-HD HD Format Up/Down/Cross Converter MENU QUICK REFERENCE Video Scaler Scaler DC Deinterlacer − Video Frame Rate − H Filter Cutoff − De-interlacer Mode (XUDC only) − H Filter Cutoff − Video Standard Input − V Filter Cutoff −...