Mitsubishi Electric MELSEC iQ-R Series User Manual page 196

Error Error definition and causes
code
D269H The station type of the REMFR/REMTO/
REMFRD/REMTOD/REMFRIP/
REMFRDIP/REMTOIP/REMTODIP
instruction target station is not a remote
station.
D26AH The target station of the REMFR/REMTO/
REMFRD/REMTOD/REMFRIP/
REMFRDIP/REMTOIP/REMTODIP
instruction does not exist.
D273H The request data size of transient
transmission is incorrect.
D275H Another dedicated instruction is in
execution, and the executed instruction
cannot be processed.
D2D2H The IP address/port No. of the target
station is incorrect.
D2D3H Send processing of the transient
transmission has failed.
D602H Parameter error
D605H Parameter error
D621H Parameter error
D628H Parameter error (station type error)
D629H Parameter error (station No. range error)
D641H Parameter error (IP address error)
D642H Parameter error (gateway address setting)
D643H Parameter error (communication cycle
setting)
4 TROUBLESHOOTING
194
4.5 List of Error Codes
Action
• Set the station type of the REMFR/REMTO/REMFRD/REMTOD/
REMFRIP/REMFRDIP/REMTOIP/REMTODIP instruction target station to
a remote station.
• Correct the network number and station number/IP address of the target
station of the dedicated instruction.
If the target station of the REMFR/REMTO/REMFRD/REMTOD/REMFRIP/
REMFRDIP/REMTOIP/REMTODIP instruction is disconnected, execute the
dedicated instruction again after return of the target station.
• Correct the request command at the transient request source, and retry
the operation.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Another dedicated instruction is in execution. Execute it again after a
while.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Execute again after correcting the port No. of the target station in the
setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Check the network status using the CC-Link IE TSN/CC-Link IE Field
diagnostics of the engineering tool, and take action.
• When the own station, target station, or relay station detected an error,
identify the cause of the error and take action.
• Execute the instruction again after correcting the target IP address of
transient data.
• If the access destination is a module with a different network No., correct
the routing parameter setting.
• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the station type in the setting
data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the station No. in the setting
data so it is within 1 to 120.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the IP address in the setting
data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the gateway address setting
in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the communication cycle
setting in the setting data.
• If the error occurs again even after taking the above, please consult your
local Mitsubishi representative.
Detailed
information 1
Detailed
information 2













