Advertisement
錯誤代碼
Error code
•縫製開始加固縫的壓腳尺寸超過
縫製開始加固縫的運針資料超過壓腳尺寸時
E494
•Presser size over of tie stitching at sewing start
When stitching data of tie stitching at sewing start
exceeds presser size.
•壓腳尺寸錯誤（僅寬方向．右側）
運針資料僅超過壓腳的寬度方向右側的尺寸時
E495
•Presser size error (Width direction : right only)
When stitching data exceeds the size of right only of
width direction of presser.
•壓腳尺寸錯誤（僅寬方向．左側）
運針資料緊超過壓腳的寬度方向左側的尺寸時
E496
•Presser size error (Width direction : left only)
When stitching data exceeds the size of left only of width
direction of presser.
•壓腳尺寸錯誤（長度方向．面前）
運針資料超過壓腳長度方向面前的尺寸時
E497
•Presser size error (Length direction : front)
When stitching data exceeds the size of front of length
direction of presser.
•壓腳尺寸錯誤（寬方向．左右）
運針資料超過壓腳的寬方向左右兩側的尺寸時
E498
•Presser size error (Width direction : right and left)
When stitching data exceeds the size of both right and
left of width direction of presser.
•壓腳尺寸錯誤（長度方向．裡側）
運針資料超過壓腳的長度方向裡側的尺寸時
E499
•Presser size error (Length direction : rear)
When stitching data exceeds the size of rear of length
direction of presser.
•操作盤連接到設定外的縫紉機上（機種錯誤）
初期通訊時，系統的機種代碼不對時
•Panel is connected to the machine other than supposed.
E703
(Machine type error)
When machine type code of system is improper in case
of initial communication.
•系統的版本不對
初期通訊時，系統軟體的版本不對時
E704
•Nonagreement of system version
When version of system software is improper in case of
initial communication.
•主軸馬達調節器不良．欠相
縫紉機馬達的調節器異常時
E730
•Main shaft motor encoder defectiveness or phase-out
When encoder of sewing machine motor is abnormal.
•主軸馬達感測器不良．位置感測器不良
縫紉機馬達感測器或位置感測器不良時
•Main motor hole sensor defectiveness or position sensor
E731
defectiveness
When hole sensor or position sensor of sewing machine
motor is defective.
•主軸馬達倒轉
縫紉機馬達倒轉時
E733
•Reverse rotation of main shaft motor
When sewing machine motor rotates in reverse direction.
•電源欠相
輸入電源欠相時
E801
•Phase-lack of power
When phase-lack of input power occurs.
P78
錯誤內容
Description
復位方法
How to recover
Place of recovery
縫製資料編輯畫面
[S64] 縫製開始加固縫
復位後可以重新啟動
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S64] Tie stitching at
sewing start width
縫製資料編輯畫面
復位後可以重新啟動
[S03] 右切刀槽寬
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S03] Knife groove width
縫製資料編輯畫面
[S04] 左切刀槽寬
復位後可以重新啟動
或 [S06] 左右形狀比率
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S04] Knife groove width,
left or [S06] Ratio of right
and left shapes
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
縫製資料編輯畫面
[S05] 左包縫寬度
復位後可以重新啟動
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S05] Overedging width,
縫製資料編輯畫面
復位後可以重新啟動
[S02] 切布長度
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S02] Cloth cut length
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
復位地點
寬度
標準畫面
left
Advertisement
