Advertisement
10. 使用初期值模式
本縫紉機設有最適的縫製形狀（30 種形狀）
的初期值。 →請參照
值資料一覽表 新編制縫製資料時，採用複
製初期值副本的方法非常便利。
1) 設為輸入模式
設為輸入模式 ① 的背景照明為藍色的輸
入模式時，可以變更圖案。背景照明為
綠色的縫製模式時，請按準備鍵 ②
變換為輸入模式。
2) 叫出初期值模式
按圖案 No. 鍵 ⑦
選擇畫面 A。現在被選擇的圖案 No.B 閃
亮，所以按項目選擇鍵 ⑩
初期值圖案
3) 選擇形狀
按形狀鍵
被顯示，現在被選擇的形狀 D 閃亮。
請選擇用資料變更鍵
狀 D。購買時，可以從 12 種形狀中進
行選擇，但是如果升級了形狀選擇等級
（K04），則最多可以從 30 種形狀中進
行選擇。→請參照 20. 記憶體開關資料
的變更方法 的內容。
4) 進行試縫
按準備鍵②
顯示①的背景照明為綠色）之後，變為
縫製模式， 可以縫製選擇的形狀。
※ 請注意，初期值圖案僅可以編輯上線張
力數據，如果變更形狀，再次叫出新的
圖案的話，必須返回初期值。
5) 複製初期值圖案
把上述步驟中選擇、確認的圖案複製到
通常圖案裡。複製方法→請參照 14. 複
製縫製圖案 的內容。
P32
. 各種形狀的初期
Ⅸ
之後，顯示出圖案
，選擇
。
之後，形狀選擇畫面 C
縫製的形
，設定為縫製模式（液晶
10.Using the initial value pattern
This sewing machine has the initial value
to perform the optimum sewing for the
sewing shapes (30 shapes). → Refer to
INITIAL VALUE DATA FOR EACH SHAPE
TABLE.When creating sewing data newly,
it is convenient to create it by copying the
initial value pattern.
1) Set the mode to the input mode.
When the back-light of LCD display ①
shows input mode in blue color, it is
possible to change the pattern. When
the back-light shows the sewing mode
in green color, Press READY key ②
to change over to the input mode.
2) Call initial value pattern.
Press PATTERN NO. key ⑦
pattern selection screen A is displayed.
Pattern No. B which is selected at
present flashes on and off on the
display. Press ITEM SELECTION key ⑩
to select initial value pattern
3) Select shape.
Press SHAPE key
selection screen C is displayed. Shape
D which is selected at present flashes
on and off on the display. Select shape
D to sew with DATA CHANGE key
. It is possible to select the shape
from among 12 shapes at the time of
your purchase. However, it is possible to
select the shape from among maximum
30 shapes by increasing the shape
selection level (K04).
→ Refer to 20. Method of changing
memory switch data.
4) Perform trial sewing.
Press READY key ②
to the sewing mode (back-light of LCD
display ① is green). Then it is possible
to perform sewing and the selected
shape can be sewn.
※Initial value pattern can edit the needle
thread tension data only. However,
it returns to the initial value when
changing the shape or performing re-
call of the pattern. So, be careful.
5) Copy initial value pattern.
Copy the pattern which has been
selected and confirmed through the
steps above to the normal pattern and
use it.Copying procedure → Refer to
14. copying sewing pattern.
Ⅸ
.
, and
.
, and shape
to set the mode
Advertisement
