Advertisement
錯誤代碼
Error code
•記憶體開關資料錯誤
記憶體開關資料損壞或是版本老時
E061
•Memory switch data error
When memory switch data is broken or revision is old.
•縫製資料錯誤
縫製資料損壞或是版本老時
E062
•Sewing data error
When sewing data is broken or revision is old.
•切刀下降指令和切線動作相碰
外部資料動作時，切刀指令的插入位置不對，與切線動作
相衝突時
•Interference of knife lowering command with thread
E099
trimming motion
When inserting position of knife command is improper
and knife command interferes with thread trimming
motion in case of motion by data from external input
device.
•放倒機頭進行確認
放倒機頭，感測器 OFF 時
E302
•Confirmation of tilt of machine head
When tilt of machine head sensor is OFF.
•主軸 Z 相感測器異常
縫紉機馬達編碼器的 Z 相感測器異常
E303
•Z phase sensor error of main shaft motor
Z phase sensor of sewing machine motorencoder is
abnormal.
•切布刀感測器錯誤
切刀下降時感測器關不了時
E304
•Cloth cutting knife sensor error
When sensor is not OFF while knife is lowered.
•圓頭扣眼長度錯誤
圓頭扣眼形狀時圓頭扣眼切刀長度過短無法縫製
E486
•Eyelet knife length error
Eyelet knife length is too short to form the shape in case
of eyelet shape.
•圓頭扣眼形狀錯誤
圓頭扣眼形狀時圓頭扣眼形狀長度過短無法縫製
E487
•Eyelet shape length error
Eyelet shape length is too short to form the shape in case
of eyelet shape.
•錐形加固補正錯誤
錐形加固形狀時加固長度過短無法縫製
E488
•Taper bar-tacking compensation error
When bar-tacking length is too short to form the shape in
case of taper bar-tacking shape.
•切刀尺寸錯誤（數次動作時）
切刀尺寸比切布刀尺寸大時
E489
•Knife size error (at the time of plural motions of knife)
When knife size is larger than cloth cutting knife size.
•下縫的壓腳尺寸超過
下縫的運針資料超過壓腳尺寸時
E492
•Presser size over of basting
When stitching data of basting exceeds presser size.
•縫製結束加固縫的壓腳尺寸超過
縫製結束加固縫的運針資料超過壓腳尺寸時
E493
•Presser size over of tie stitching at sewing end
When stitching data of tie stitching at sewing end
exceeds presser size.
錯誤內容
Description
Introduction
復位方法
How to recover
Place of recovery
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
縫製資料編輯畫面
復位後可以重新啟動
[S17] 圓頭扣眼切刀長度
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S17] Eyelet knife length
縫製資料編輯畫面
復位後可以重新啟動
[S14] 圓頭扣眼形狀長度
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S14] Eyelet shape length
縫製資料編輯畫面
[S08] 第 2 加固縫長度
復位後可以重新啟動
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S08] 2nd bar-tacking
縫製資料編輯畫面
復位後可以重新啟動
[S02] 切布長度
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S02] Cloth cut length
縫製資料編輯畫面
[S40] 下縫落針補正
復位後可以重新啟動
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S40] Basting needle
entry compensation
縫製資料編輯畫面
[S67] 縫製結束加固縫
復位後可以重新啟動
Possible to re-start after
Sewing data edit screen
pressing reset key.
[S67] Tie stitching at
sewing end width
復位地點
標準畫面
標準畫面
length
寬度
P77
Advertisement
