Advertisement
Ⅷ . 錯誤代碼一覽表
錯誤代碼
Error code
•主控制電路板的 EEP-ROM 初期化
EEP-ROM 裡沒有寫入資料，或資料損壞時，自動進行通知
進行了初期化。
E001
•Contact of initialization of EEP-ROM of MAIN CONTROL
p.c.b.
When data is not written in EEP-ROM or data is broken,
initialization of the data is automatically informed.
•主軸馬達被鎖定
縫製了大於機針阻抗的縫製物後
E007
•Main shaft motor-lock
When large needle resistance sewing product is sewn.
•EEP-ROM 的形式不對
安裝的 EEP-ROM 形式不對時
E018
•Type of EEP-ROM is wrong.
When the type of mounted EEP-ROM is wrong.
•檢測出壓腳提升馬達異常
通過壓腳提升馬達原點感測器時和動作開始時馬達異常時
•Detection of step-out of presser lifting motor
E023
When step-out of motor is detected at the time when
presser lifting motor passes origin sensor or starts
operation.
•圖案資料尺寸超過
連續縫製資料的總尺寸和下載的資料尺寸過大，不能進行
縫製時
E024
•Pattern data size over
When sewing cannot be performed since total size of
continuous stitching data or size of downloaded data is
too large.
•檢測出上線切線馬達異常
通過上線切線馬達原點感測器時和動作開始時馬達異常時
•Detection of step-out of needle thread trimmer motor
E025
When step-out of motor is detected at the time when
needle thread trimmer motor passes origin sensor or
starts operation.
•檢測出底線切線馬達異常
通過底線切線馬達原點感測器時和動作開始時馬達異常時
•Detection of step-out of bobbin thread trimmer motor
E026
When step-out of motor is detected at the time when
bobbin thread trimmer motor passes origin sensor or
starts operation.
•針桿上位置偏離
縫紉機啟動時，讓機針上動作，但是機針不能在上位置停
止時
E030
•Needle bar upper position failure
When needle does not stop at UP position even with
needle UP operation at the time of starting sewing
machine.
•停止開關
縫紉機啟動途中按了停止開關時
E050
•Stop switch
When stop switch is pressed during machine running.
•斷線檢測錯誤
縫紉機啟動途中發生了斷線時
E052
•Thread breakage detection error
When thread breakage has occurred during machine
running.
P76
Ⅷ .ERROR CODE LIST
錯誤內容
Description
復位方法
How to recover
Place of recovery
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
電源 OFF
Turn OFF the power.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
Standard screen
pressing reset key.
復位後可以重新啟動
Possible to re-start after
pressing reset key.
復位後可以重新啟動
Possible to re-start after
pressing reset key.
復位地點
標準畫面
標準畫面
標準畫面
標準畫面
標準畫面
步驟畫面
Step screen
步驟畫面
Step screen
Advertisement
