Advertisement
•平行部間隔
設定左右平行部的縫製間隔
S07
•Pitch at parallel section
This item sets sewing pitch of left and right parallel sections.
•第 2 加固部長度
設定面前的加固部長度
•2nd bar-tacking length
This item sets length of bar-tacking on the front side.
S08
角型下
Bottom of
square type
•第 1 加固部長度
設定裡側加固部的長度
S09
•1st bar-tacking length
This item sets length of bar-tacking on the rear side.
•加固部右寬度修正
調整加固部的右側外型和包縫部
第 1 加固、第 2 加固均被修正
•Compensation of bar-tacking width, right
This item adjusts right side outer shape of bar-tacking section in terms of
S10
overedging section.
The first section and second section have been compensated.
角型上
角型下
Top of
Bottom of
square type
square type
• 加固部左寬度修正
調整加固部的左側外形和包縫部
•Compensation of bar-tacking width, left
This item adjusts left side outer shape of bar-tacking section in terms of
S11
overedging section.
角型上
角型下
Top of
Bottom of
square type
square type
•錐形加固部左對稱
設定形成錐形加固形狀的加固部的長度
S12
•Taper bar-tacking offset, left
This item sets length to form bar-tacking section of taper bar-tacking shape.
•錐形加固部右對稱
設定形成錐形加固形狀的加固部的長度
S13
•Taper bar-tacking offset, right
This item sets length to form bar-tacking section of taper bar-tacking shape.
•圓頭扣眼形狀長度
設定從圓頭扣眼形狀的圓頭扣眼中心到上側的長度
S14
•Eyelet shape length
This item sets upper side length from center of eyelet of eyelet shape.
•圓頭扣眼形狀針數
設定圓頭扣眼形狀的上部 90 度中的縫製條數
S15
•Number of stitches of eyelet shape
This item sets number of stitches in the upper 90° of eyelet shape.
•圓頭扣眼寬度
設定圓頭扣眼形狀的內側橫尺寸
實際的落針處為加算上 S04 切刀槽左寬度的尺寸
S16
•Eyelet width
This item sets crossuise size of the inside of eyelet shape.
Actual needle entry point is the dimension to which S04 Knife groove
width, left is added.
•圓頭扣眼長度
設定圓頭扣眼形狀的內側豎尺寸
S17
•Eyelet length
This item sets lengthwise size of the inside of eyelet shape.
直線加固下
錐形下
Bottom of
Bottom of
straight
taper
bar-tacking
角型上
Top of
square type
直線加固下
Bottom of straight
bar-tacking
直線加固下
Bottom of straight
bar-tacking
Introduction
0.200∼2.500
0.025mm
–
0.2∼5.0
0.1mm
–
0.2∼5.0
0.1mm
–
-1.00 ∼ 1.00
0.05mm
–
-1.00∼1.00
0.05mm
–
0.00∼3.00
0.05mm
*1
0.00∼3.00
0.05mm
*1
1.0∼10.0
0.1mm
*1
1∼8
1
*1
1.0∼10.0
0.1mm
*1
1.0∼10.0
0.1mm
*1
P39
Advertisement
