Advertisement
No.
•倒轉針提升 允許／禁止
U01 壓腳提升最高位置被設定為 14.0mm 以上時，
自動地倒轉針提升，縫紉機停機。
也可以設定禁止此動作。
K11
•Needle up by reverse run Permitted/Prohibited
When U01 Presser lifter maximum position is set to
14.0 mm or more, motion of needle up by reverse run
is automatically performed and the machine stops.
Prohibition of the motion can be set.
•設定切刀電磁下降時間
K12
•Knife solenoid lowering time setting
•設定切刀電磁上升時間
K13
•Knife solenoid lifting time setting
•切刀缸筒下降時間（選購）
K14
•Knife cylinder lowering time (Optional)
•Y 送布馬達基準點補正
K15
•Y-feed motor origin compensation
•針擺動馬達基準點補正
K16
•Needle-rocking motor origin compensation
•壓腳提升馬達基準點補正
K17
•Presser lifter motor origin compensation
•縫製模式下的圖案選擇功能 無效／有效
K18
•Pattern selection function under sewing
mode Ineffective/effective
•連續縫製途中切線 允許／禁止
K19
•Thread trimming on the way in
continuous stitching Permitted/Prohibited
•切布刀返回動力
設定切部刀返回時的輸出動力。
K20
•Cloth cutting knife return power
This item sets output power at the time of returning the cloth cutting knife.
•縫製開始底線切線剪的開放量
設定縫製開始底線切線剪的開放量。
K21
•Release amount of bobbin thread trimmer at the start of sewing
This item sets the amount of releasing the bobbin thread trimmer
at the statrt of sewing.
•壓腳提升速度
設定壓腳提升速度。
K22
•Presser lifter speed
This item sets presser lifter speed.
•上線切線調整模式開始
用準備鍵 ON 開始上線切線動作的調整。
K51
•Needle thread trimming adjustment mode start
Needle thread trimming adjustment motion starts with READY key ON.
•底線切線調整模式開始
用準備鍵 ON 開始底線切線動作的調整。
K52
•Bobbin thread trimming adjustment mode start
Bobbin thread trimming adjustment motion starts with READY key ON.
•感測器確認模式開始
用準備鍵 ON 開始確認感測器。
K53
•Sensor check mode start
Sensor check starts with READY key ON.
項目
Item
許可倒轉針提升
Needle up by reverse
run prohibited
禁止倒轉針提升
Needle up by reverse
run permitted
無效
Ineffectiverun
允許
Permitted
Introduction
設定範圍
編輯單位
Setting range
Edit unit
ー
25 ～ 100
5ms
5 ～ 100
5ms
5 ～ 300
5ms
1 脈衝
(0.025mm)
-120 ～ 400
1pulse
(0.025mm)
1 脈衝
(0.05mm)
-10 ～ 10
1pulse
(0.05mm)
1 脈衝
(0.05mm)
-100 ～ 10
1pulse
(0.05mm)
有效
ー
Effective
禁止
ー
Prohibited
0 ～ 3
1 脈衝
0 ～ 15
1pulse
1 ～ 3
ー
ー
ー
初期值
Initial value
允許
ー
Permitted
35
15
50
0
0
0
無效
ー
Ineffective
允許
ー
Permitted
1
0
8
ー
2
ー
ー
ー
ー
ー
ー
P65
Advertisement
