Advertisement
13. 縫製數據一覽表
☆縫製資料為圖案 1 ～ 99 的 99 個圖案的可
以輸入的資料，可按每種圖案進行輸入。
購買時，為不能選擇設定有／無編輯資料的
狀態。使用時，請根據需要變換為有編輯的
狀態後再使用。→請參照 12. 縫製資料編輯
有／無的設定方法 。
＊ 1 : 不同的形狀有不同的顯示。
＊ 2 : 設定為有編輯之後被顯示。請參照 12.
縫製資料編輯有／無的設定方法 。
＊ 3 : 選擇功能之後，被顯示。
No.
•縫製形狀
可以從縫紉機所具有的 30 種縫製形狀中選擇形狀
•Sewing shape
This item selects the shape from among the sewing shapes of 30 different kinds which
the sewing machine has.
–
S01
※購入時，只能選擇標準的 12 種縫製形狀
增加形狀種類時，請進行記憶體開關資料 K04 縫製
形狀等級的設定。→請參照 21. 記憶體開關資料一覽表
※Only 12 kinds of standard sewing shapes can be selected at the time of your purchase.
When increasing the kinds of shapes, perform setting of K04 Sewing shape selection level
of memory switch data. → Refer to 21. Memory switch list.
•切布長度
設定切布刀切斷縫製品的長度。但是，條形卷褶形狀
（S01 的形狀 NO.27、28、29、30）時，只能
設定縫製長度。將記憶體開關資料的 U19 切布
刀數次動作功能設定為有效之後，就可以按照
U18 切布刀尺寸設定的切刀尺寸，讓切刀數
次動作，切斷縫製品。
S02
→請參照 21. 記憶體開關資料一覽表
•Cloth cut length
This item sets the length of cloth that is cut by cloth cutting knife. However, in case of
bar-tack shape (Nos. 27, 28, 29, and 30 of S01), sewing length is set. By making
effective U19 Function of plural motions of cloth cutting knife of memory switch data,
make the plural motions of knife by the knife size set in the item U18 Cloth cutting knife
size, and the sewing product is cut. →Refer to 21. Memory switch list.
•右切刀槽寬度
設定切布刀和右平行部的間隙
S03
•Knife groove width, right
This item sets the clearance between cloth cutting knife and
right parallel section.
•左切刀槽寬度
設定切布刀和左平行部的間隙
S04
•Knife groove width , left
This item sets the clearance between cloth cutting knife and left parallel section.
•左包邊寬度
設定左平行部的包邊寬度
S05
•Overedging width, left
This item sets the overedging width of left parallel section.
•左右形狀比率
設定以切刀位置為中心的右側形狀的擴大縮小率
S06
•Ratio of right and left shapes
This item sets enlargement/reduction ratio of right side shape making the
knife position as the center.
P38
項目
Item
參照Ⅱ-3 .標準縫製形狀一覽表
Refer to Ⅱ-3. Standard sewing shape list.
13.Sewing data list
☆ Sewing data are those that can be inputted
to 99 patterns from pattern 1 to 99 and can
be inputted to each pattern. The sewing
machine has been set in the state that
the data which is necessary to set"With/
without edit＂cannot be selected at the
time of your purchase. Change over the
function to"With edit＂if necessary for
the use. → Refer to 12. Method of setting
sewing data with/without edit.
＊ 1 : Displayed according to the shape
＊ 2 : Displayed when it is set to with edit.
Refer to 12. Method of setting sewing
data with/without edit.
＊ 3 : Displayed when the function is
selected.
設定範圍
Setting range
3.0∼119.6
-2.00∼2.00
-2.00∼2.00
0.10∼5.00
50∼150
編輯單位
備考
Edit unit
Remarks
1∼30
1
-
0.1mm
–
0.05mm
–
0.05mm
–
0.05mm
–
1%
–
Advertisement
