Advertisement
⑵連續縫製資料的編輯方法
1) 設定為輸入模式
液晶顯示①的背景照明為藍色的輸入模式
時，可以輸入連續縫製資料。背景照明為
綠色的縫制模式時，請按準備鍵②
換為輸入模式。
2) 叫出編輯的連續縫製資料 NO.
按圖案 NO. 鍵⑦
之後，現在被選擇的圖案 NO.B 閃亮顯
示。按項目選擇鍵⑩
的圖案順次變換顯示，最後的登記的圖案
NO. 之後顯示被登記的迴圈資料 NO.，連
續縫製 NO.。在這裡請選擇想縫製的連續
縫製資料 NO.。
3) 把連續縫製資料設定為編輯狀態
按資料鍵⑧
料編輯顯示 C，最初縫製的圖案 NO.D 閃
亮顯示。在此狀態下可以編輯資料。
4) 選擇編輯要點
按項目選擇鍵⑩
→空送量→圖案 NO. →空送量的順次編
輯要點移動顯示。 進入到資料的最後編
輯要點之後，顯示出追加指示圖示
5) 變更選擇的編輯要點的資料
按數據變更鍵
輯要點的資料。 編輯要點為圖案 NO. 時
被登記的圖案 NO. 被顯示成為可以選擇
的狀態。 編輯要點為空送時在 ±120MM
的範圍內可以編輯數值。另外，按復位鍵
③
之後，可以消除編輯要點的圖案資
料。 請重複步驟 4)，步驟 5)，編輯資料。
P52
，叫出圖案選擇畫面
之後，被登記
之後，顯示出連續縫製資
之後，按圖案 NO.
。
之後，可以變更編
(2) Method of editing continuous stitching
data
1) Set the mode to the input mode.
When the back-light of LCD display ①
shows the input mode in blue color, it is
變
possible to select continuous stitching
data. When the back-light shows the
sewing mode in green color, press
READY key ②
input mode.
2) Call continuous stitching data No. to
edit.
Press PATTERN No. key ⑦
call pattern selection screen, and
pattern No. B which is selected at
present flashes on and off. Press
ITEM SELECTION key ⑩
patterns which have been registered are
changed over and displayed in order.
Cycle data No. and continuous stitching
data No. which have been registered
after the last pattern No. are displayed.
Here, select the continuous stitching
No. which you desire to sew.
3) Set continuous stitching data to editing
status.
Press DATA key ⑧
stitching data editing display C appears.
Pattern No. D which is sewn first flashes
on and off. In this state, it is possible to
edit the data.
4) Select editing point.
Press ITEM SELECTION key ⑩
, and editing point moves in
order of "pattern No. → jump feed
mount → pattern No. → jump feed
amount" and flashes on and off. When
moving the editing point up to the last
data, additional indication pictograph
is displayed.
5) Change data of selected editing point.
Press DATA CHANGE key
data of editing point can be changed.
When the editing point is at the pattern
No. :Pattern No. which has been
registered is displayed and it is possible
to select.
When the editing point is at the jump
feed :It is possible to edit numerical
value within the range of ±120 mm. In
addition, press RESET key ③
the pattern data of editing point can be
deleted.
Repeat steps 4) and 5) to perform
editing data.
to change over to the
to
, and
, and continuous
, and
and
Advertisement
