Advertisement
•縫製結束加固縫寬度
設定縫製結束加固縫的寬度
S67
•Tie stitching width at the end of sewing
This item sets tie stitching width at the end of sewing.
•縫製結束加固縫針數
設定縫製結束加固縫的針數
S68
•Number of stitches of tie stitching at the end of sewing
This item sets number of stitches of tie stitching at the end of sewing.
•縫製結束加固縫豎向修正
設定縫製結束加固縫的豎方向開始位置
S69
•Lengthwise compensation of tie stitching at the end of sewing
This item sets start position of tie stitching in lengthwise direction at
the end of sewing.
•縫製結束加固縫橫向修正
設定縫製結束加固縫的橫方向開始位置
S70
•Crosswise compensation of tie stitching at the end of sewing
This item sets start position of tie stitching in crosswise direction
at the end of sewing.
•切刀動作
設定通常的切布刀動作有 無
•Knife motion
S81
This item sets "With/without motion" of normal cloth cutting knife.
：通常切刀動作 OFF
：Normal knife motion OFF
•雙重縫的第 1 迴圈切刀
雙重縫時，設定第 1 迴圈的切布刀有 無動作。
•Knife motion at 1st cycle of double stitching
This item sets "With/without motion" of cloth cutting knife at 1st cycle
S83
when double stitching is performed.
：通常切刀動作 OFF
：Normal knife motion OFF
•最高速度限制
設定縫紉機的最高轉速。
資料編輯的最大值為記憶體開關資料 K07 最大轉速限制速度的設定的轉速。
→請參照 21. 記憶體開關數據一覽表。
S84
•Maximum speed limitation
This item sets max. speed limitation of the sewing machine. The maximum value
of data edit is equal to the number of revolutions of K07 Maximum speed limitation
of the memory switch data.→Refer to 21. Memory switch list
•前進間隔
設定條形衣褶形狀 (S01 的形狀 NO.27、28、29、30)前進側的縫製間隔。
S86
•Pitch of going
This item sets sewing pitch of going side of bar-tacking shape
(Shape Nos. 27, 28, 29 and 30 of S01).
•前進寬度
設定條形衣褶形狀 (S01 的形狀 NO.27、28、29、30)前進側的縫製寬度。
S87
•Width of going
This item sets width of going side of bar-tacking shape
(Shape Nos. 27, 28, 29 and 30 of S01).
•返回間隔
設定條形衣褶形狀 (S01 的形狀 NO.27、28、29、30)返回側的縫製間隔。
S88
•Pitch of coming
This item sets sewing pitch of coming side of bar-tacking shape
(Shape Nos. 27, 28, 29 and 30 of S01).
•返回寬度
設定條形衣褶形狀(S01 的形狀 NO.27、28、29、30)返回側的縫製寬度。
S89
•Width of coming
This item sets width of coming side of bar-tacking shape
(Shape Nos. 27, 28, 29 and 30 of S01).
：通常切刀動作 ON
：Normal knife motion ON
：通常切刀動作 ON
：Normal knife motion ON
Introduction
0.1∼1.5
0.1mm
–
0∼8
1
–
0.0∼5.0
0.1mm
*2
0.0∼2.0
0.1mm
*2
–
–
–
–
–
*2, *3
400∼4200
100sti/min
–
0.200∼2.500
0.025mm
–
0.1∼10.0
0.05mm
–
0.200∼2.500
0.025mm
–
0.1∼10.0
0.05mm
–
P43
Advertisement
