B&R Automation Panel 5000 User Manual page 130

Technical data
Model number
Selector switch
Quantity
Type
Contact element
Key switch
Quantity
Type
Contact element
Emergency stop
Quantity
Type
Contact element
Operating conditions
Pollution degree per EN 61131-2
Mechanical properties
Material
Weight
P01.215C-000, 5ACCKP01.215I-000, 5ACCKP01.240C-000 - Technical data
4.2.5.2.4 USB interface
The expansion unit is equipped with a USB 2.0 interface. This is equipped with a protective cover.
Caution!
IP65 protection can only be achieved if the USB protective cover is properly installed.
Warning!
USB peripheral devices can be connected to the USB interfaces. Due to the variety of USB devices
available on the market, B&R cannot guarantee their functionality. The functionality of USB devices
available from B&R is guaranteed.
Caution!
Due to the general PC specification, this interface must be handled with the utmost care with regard
to EMC, cable routing, etc.
The USB interface is internally connected to the system via USB 2.0 and available to the user for service purposes.
Depending on the transfer method (SDL, DVI, SDL3 or SDL4 operation), there may be limitations with regard to the
transfer rate of the USB interfaces. For possible transfer methods, see section
Transfer method
SDL operation without USB cable
SDL operation with USB cable
Single-touch DVI operation
Multi-touch DVI operation
SDL3 operation
SDL4 operation
1) The max. cable length of 25 m depends on the resolution. For exact specifications, see table
Standard
Variant
Transfer rate
Current-carrying capacity
3)
Cable length
USB 2.0
1) The interfaces, etc. available on the device or module have been numbered for the purpose of clear differentiation. This numbering may deviate from the
numbering used by the respective operating system, however.
2) In SDL operation without USB cable (mode 1), the USB transfer rate is limited to USB 1.1.
In SDL3 operation: Low speed (1.5 Mbit/s), full speed (12 Mbit/s) to high speed (30 Mbit/s)
In SDL4 operation: Low speed (1.5 Mbit/s), full speed (12 Mbit/s) to high speed (150 Mbit/s)
3) The USB interface is protected by a maintenance-free "USB current-limiting switch" (max. 0.5 A).
130
5ACCKP01.156B-000 5ACCKP01.185B-000 5ACCKP01.215C-000 5ACCKP01.215I-000 5ACCKP01.240C-000
800 g
Table 60: 5ACCKP01.156B-000, 5ACCKP01.185B-000, 5ACCK-
USB type Max. cable length
USB 1.1 25 m
USB 2.0 5 m
USB 2.0 5 m
USB 2.0 5 m
USB 2.0 100 m
USB 2.0 100 m
Front USB of the expansion unit
USB 2.0
Type A, female
Low speed (1.5 Mbit/s)
Full speed (12 Mbit/s)
High speed (480 Mbit/s)
Max. 0.5 A
<3 m (without hub)
-
1
RAFIX 22 FS+, 1.30.272.102/2200
Maintained
1
RAFIX 22 FS 1.30.255.222/0000
Maintained
1
RAFIX 22 FS+, Plus 1, 1.30.273.512/0300
Maintained
Pollution degree 2
Steel sheet
900 g 1000 g
1)
"Title" on page 51
1)
2)
700 g
"Connection options" on page
" in the AP5000 user's manual.
Automation Panel 5000 User's manual V2.11
1100 g
21.