Danfoss VLT 5000 Series Instruction Manual page 17

Compact, AC line supply 3 x 200-240 V
According to international requirements
Normal overload torque (110 %):
Output current
Output (240 V)
Typical shaft output
Typical shaft output
High overload torque (160 %):
Output current
Output (240 V)
Typical shaft output
Typical shaft output
Max. cable cross-section to motor,
brake and load sharing [mm
Min. cable cross-section to motor, brake and
load sharing
Rated input current
Max. cable cross-section,
power [mm
Max. pre-fuses
Efficiency
Weight IP 20 EB
Weight IP 54
Power loss at max. load.
- high overload torque
(160 %)
- normal overload torque
(110 %)
Enclosure
1. For type of fuse, see section Fuses.
2. American Wire Gauge.
3. Measured using 100 ft [30 m] shielded motor cables at rated load and rated frequency.
4. Min. cable cross-section is the smallest cable cross-section allowed to be fitted on the terminals to comply with IP 20. Always comply
with national and local regulations on min. cable cross-section.
5. Aluminum cables with cross-section above 0.054 in
14
VLT type
I
VLT,N
I (60 s)
VLT, MAX
S [kVA]
VLT,N
P [kW]
VLT,N
P [HP]
VLT,N
I
VLT,N
I (60 s)
VLT, MAX
S [kVA]
VLT,N
P [kW]
VLT,N
P [HP]
VLT,N
2 2) 5)
/AWG]
4) 2 2)
[mm /AWG]
(200 V) I
L,N
2 2) 5)
]/[AWG]
1)
[-]/UL
3)
[kg]
[kg]
[W]
[W]
2 2
[35 mm ] must be connected by use of an AI-Cu connector.
®
VLT 5000 Series
5008 5011
[A] 32 46
35.2 50.6
[A]
13.3 19.1
7.5 11
10 15
[A] 25 32
40 51.2
[A]
10 13
5.5 7.5
7.5 10
IP 54 16/6 16/6
IP 20 16/6 35/2
10/8 10/8
[A] 32 46
IP 54 16/6 16/6
IP 20 16/6 35/2
50 60
[A]
0.95 0.95
21 25
38 40
340 426
426 545
IP 20/ IP 20/
IP 54 IP 54
MG.51.C5.22 - VLT is a registered Danfoss trademark.
5016 5022 5027
61.2 73 88
67.3 80.3 96.8
25.4 30.3 36.6
15 18.5 22
20 25 30
46 61.2 73
73.6 97.9 116.8
19 25 30
11 15 18.5
15 20 25
35/2 35/2 50/0
35/2 35/2 50/0
10/8 10/8 16/6
61 73 88
35/2 35/2 50/0
35/2 35/2 50/0
80 125 125
0.95 0.95 0.95
27 34 36
53 55 56
626 833 994
783 1042 1243
IP 20/ IP 20/ IP 20/
IP 54 IP 54 IP 54