Danfoss VLT 5000 Series Instruction Manual page 121

Outputs
Value:
0-100 Hz 0-20 mA
0-100 Hz 4-20 mA
0-100 Hz 0-32000 p
0 - f 0-20 mA
MAX
0 - f 4-20 mA
MAX
0 - f 0-32000 p
MAX
Ref - Ref 0-20 mA
MIN MAX
Ref - Ref 4-20 mA
MIN MAX
Ref - Ref 0-32000 p
MIN MAX
FB - FB 0-20 mA
MIN MAX
FB - FB 4-20 mA
MIN MAX
FB - FB 0-32000 p
MIN MAX
0 - I 0-20 mA
MAX
0 - I 4-20 mA
MAX
0 - I 0-32000 p
MAX
0 - T 0-20 mA
LIM
0 - T 4-20 mA
LIM
0 - T 0-32000 p
LIM
0 - T 0-20 mA
NOM
0 - T 4-20 mA
NOM
0 - T 0-32000 p
NOM
0 - P 0-20 mA
NOM
0 - P 4-20 mA
NOM
0 - P 0-32000 p
NOM
0 - SyncRPM 0-20 mA
0 -SyncRPM 4-20 mA
0 - SyncRPM 0-32000 p
0 - RPM at FMAX 0-20 mA
0 - RPM at FMAX 4-20 mA
0 - RPM at FMAX 0-32000 p
319 Terminal 42, output
(AO 42 FUNCT.)
Function:
This output can act both as a digital and an analogue
output. If used as a digital output (data value [0]-[65]),
a 24 V DC signal is transmitted; if used as an analogue
output either a 0-20 mA signal, a 4-20 mA signal or a
pulse output is transmitted.
Description of choice:
Control ready, the frequency converter is ready for use;
the control card receives supply voltage.
Ready signal, the frequency converter control card is
receiving a supply signal and the frequency converter
is ready for operation.
= factory setting, () = display text, [] = value for use in communication via serial communication port
118
terminal no.
parameter
(0-100 Hz = 0-20 mA)
(0-100 Hz = 4-20 mA)
(0-100 Hz = 0-32000P)
(0-FMAX = 0-20 mA)
(0-FMAX = 4-20 mA)
(0-FMAX = 0-32000P)
(REF MIN-MAX = 0-20 mA)
(REF MIN-MAX = 4-20 mA)
(REF MIN-MAX = 0-32000P)
(FB MIN-MAX = 0-20 mA)
(FB MIN-MAX = 4-20 mA)
(FB MIN-MAX = 0-32000P)
(0-IMAX = 0-20 mA)
(0-IMAX = 4-20 mA)
(0-IMAX = 0-32000P)
(0-TLIM = 0-20 mA)
(0-TLIM = 4-20 mA)
(0-TLIM = 0-32000P)
(0-TNOM = 0-20 mA)
(0-TNOM = 4-20 mA)
(0-TNOM = 0-32000P)
(0-PNOM = 0-20 mA)
(0-PNOM = 4-20 mA)
(0-PNOM = 0-32000P)
(0-SYNCRPM = 0-20 mA)
(0-SYNCRPM = 4-20 mA)
(0-0-SYNCRPM = 0-32000 p)
(0-RPMFMAX = 0-20 mA)
(0-RPMFMAX = 4-20 mA)
(0-RPMFMAX = 0-32000 p)
Ready, remote control, the frequency converter control
card is receiving a supply signal and parameter 002
has been set to remote control.
Enable, no warning, the frequency converter is ready
for use; no start or stop command has been given
(start/disable). No warning.
Running is active when there is a start command or the
output frequency is above 0.1 Hz. Is also active during
ramp down.
Running, no warning , the output frequency is higher
than the frequency set in parameter 123. A start com-
mand has been given. No warning.
Runs in range, no warning, runs within the programmed
current/frequency ranges set in parameters 223-226.
MG.51.C5.22 - VLT
®
VLT 5000 Series
42 45 01(relay) 04 (relay)
319 321 323
[36] [36]
[37] [37]
[38] [38]
[39]
[39]
[40] [40]
[41] [41]
[42] [42]
[43] [43]
[44] [44]
[45] [45]
[46] [46]
[47] [47]
[48]
[48]
[49] [49]
[50] [50]
[51] [51]
[52] [52]
[53] [53]
[54] [54]
[55] [55]
[56] [56]
[57] [57]
[58] [58]
[59] [59]
[60] [60]
[61] [61]
[62] [62]
[63] [63]
[64] [64]
[65] [65]
is a registered Danfoss trademark.
326