Parameter Index And Indications On The Display - AUMA AUMATIC AC 01.1 Manual

Manual

Parameter index and indications on the display

A
ADAPTIVE BEHAVIOUR
ALARM CONTACT
ANALOGUE VALUES DP
B
BEHAVIOUR-LOSS OF E1
BLINKER
BY-PASS DURATION
BYTE 5.0 CONFIG.
BYTE 5.7 CONFIG.
BYTE 6.0 CONFIG.
BYTE 7.0 CONFIG.
BYTE 8.0 CONFIG.
BYTE ORDER PATTERN
C
CHANGE PASSWORD
CLOSED POSITION
CLOSING
CLOSING DEADBAND
CONTROL LIMIT CLOSE
CONTROL LIMIT OPEN
D
DEAD TIME
DELAY TIME
DERIVATIVE GAIN KD
DIAGNOSTIC INDICATIONS
D0 – END POS. INPUTS
D1 – ACTUATOR SIGNALS
D14 – BT-OSS-HW-VERSI
D15 – BT-OSS-SW-VERSI
D16 - BLUETOOTH STATUS 106
D2 – INTERNAL FAULTS
D3 – INTERNAL WARNINGS
D4 – CONFIGURATION FAULT99
D5 – LOGIC HRDWR.VER.
D6 – LOGIC SFTWR.VER.
D7 – POT. VALUE
D8 - RWG VALUE
D9 - MWG VALUE
DA - MWG HRDWR.VER.
DB - MWG SFTWR.VER.
DC - DP1 HRDWR.VER
DD - DP1 SFTWR.VER.
DD - MWG STATUS
DE - DP1 BUS STATUS
DF - POSITIONER
DG - DP2 HRDWR.VERS.
DH - DP2 SFTWR.VER.
DI - DP2 BUS STATUS
DJ - E1 VALUE
DQ – INTERNAL FAULTS
DIRECTION CLOSE
DIRECTION OPEN
DP1 ANLOG IN1 END
55 DP1 ANLOG IN1 START
DP1 ANLOG IN2 END
29
DP1 ANLOG IN2 START
26
DP-V1 SERVICES
E
66
E4 MAX. REACTION
21,30
E4 MIN. REACTION
84
E4 REACTION TIME
23
EL. NAME PLATE
25
EMERG.SEL.SW.POS.
23
EMERGENCY BEHAVIOUR
23
EMERGENCY BY-PASS
23
EMERGENCY POSITION
22
ENABLE LOCAL MODE
END POSITION OPEN
13
EXTERNAL INPUTS BUS
45,47
F
46
FAILURE ACTION
56
FAILURE BEHAVIOUR
67
FAILURE POSITION
67
FAILURE SOURCE
FEEDBACK E2
57
FULL CLOSE ADJUST
43
FULL OPEN ADJUST
64
I
I/O 1
97
I/O STACK 2
97
I/O1 ANALOG OUT1
105
I/O1 ANALOG OUT1 TYPE 33
105
I/O1 ANALOG OUT2
I/O1 ANALOG OUT2 TYPE 34
98
I/O1 ANLOG IN1 END
99
I/O1 ANLOG IN1 START
INTERMED. POSITION
99
INTERNAL SET POINT
100
INVERSE OPERATION
100
(PROCESS CONTROLLER)
100
101
L
101
LANGUAGE
101
LCD CONTRAST
102
LED 1 (LEFT HAND)
102
LED 2
101
LED 3
102
LED 4
103
LED 5 (RIGHT HAND)
103
LOCAL CLIENT
104
M
104
104 MAINTAINED LOCAL
104 MAINTAINED REMOTE
71 MAX. DUTY CYCLE
71 MAX. RUN TIME
AUMATIC AC 01.1/ACExC 01.1 Profibus DP
60 MAX. STARTS/HOUR
MONITOR TRIGGERS 86,87,88
60
69 MOTOR PROTECTION
69
O
79
OFF TIME CLOSE
OFF TIME OPEN
68 ON TIME CLOSE
68 ON TIME OPEN
68 OPEN POSITION
17 OPENING
38 OPENING DEADBAND
39 OPERATIONAL DATA
40 ORDER DATA
39 OUTER DEADBAND
73 OUTPUT CONTACT 1
45 OUTPUT CONTACT 2
80 OUTPUT CONTACT 3
OUTPUT CONTACT 4
OUTPUT CONTACT 5
43
P
41
42 PID TYPE
42 POS NUMBER
31 POS. 1
58 POS. DIRECTRUNNING
58 POS.1 BEHAVIOUR
POS.1 CONTROL
POS.1 SELECTOR SW
37
POSITIONER
78
PRESET POSITION
32
PROCESS CONTROL PID
PRODUCT DATA
34
PROJECT DATA
PROPORT. GAIN KP
60
R
60
48 RATE TIME TD
65 REACTION MONITORING
RESET TIME TI
66
S
SEATING MODE
14 SERVICE DATA
14 SET LIMIT SWITCHES
20 SETPOINT E1
20 SLAVEADDRESS
20 START STEP CLOSE
20 START STEP OPEN
20 STEPPING MODE
12 STOP STEP CLOSE
STOP STEP OPEN
T
36
37 TORQUE
87 TORQUE E6
88 TORQUE INDICATION
Actuator controls
87
85
72
72
72
72
47
46
56
95
17
57
27
27
27
27
27
65
54
49,53
52
50
50
49
53
40,43
62
17
17
63
64
89
63
45
17
47
59
77
71
71
70
71
71
46,84
32
16
109