AUMA AUMATIC AC 01.1 Manual page 3

Manual
5.3.4 Signal range at the analogue output 1: view/edit
5.3.5 Feedback signals (configuration) via analogue output 2: view
5.3.6 Signal range at the analogue output 2: view/edit
6 Operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.1 Operation mode OFF
6.2 Operation mode LOCAL
6.2.1 Push-to-run operation or self-retaining: set for operation mode LOCAL
6.3 Operation mode REMOTE
6.3.1 Push-to-run operation or self-retaining: set for operation mode REMOTE
6.4 Operation mode EMERGENCY
6.4.1 Operation mode (type of duty) activation for an EMERGENCY operation
6.4.2 EMERGENCY operation: switch on or off/signal behaviour definition
6.4.3 Actuator behaviour definition in case of an EMERGENCY operation
6.4.4 EMERGENCY position definition
6.4.5 Motor protection and/or torque switching: by-pass
6.5 Operation mode FAILURE
6.5.1 Failure behaviour: switch on or off
6.5.2 Source for initiation (failure source): set for failure operation
6.5.3 Actuator reaction (failure position): set on loss of signal
6.5.4 Preset position definition
6.5.5 Failure delay time setting
6.5.6 Failure behaviour on bus communication loss
7 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7.1 Type of seating: check/edit end positions
7.2 Torque switching: check/set
7.3 Limit switching setting
7.4 Intermediate positions (option)
7.4.1 Display indication: enable view
7.4.2 Intermediate positions: switch on or off
7.4.3 Intermediate position definition
7.4.4 Operation behaviour = actuator behaviour definition
7.4.5 Intermediate positions: set the signalling
7.5 Intermediate positions with multiport valve function (option)
7.5.1 Check: Multiport valve function availablequestion
7.5.2 Check: Positioner active?
7.5.3 Display indication: enable view
7.5.4 Intermediate positions: switch on or off
7.5.5 Intermediate position setting
7.5.6 Operation behaviour = actuator behaviour definition
7.5.7 Intermediate positions signalling
7.5.8 Intermediate positions in LOCAL: direct approach without stopping
7.6 Positioner (operation mode SETPOINT MODE)
7.6.1 Adaptive behaviour: switch on or off
7.6.2 Overrun (inner dead band): set manually
7.6.3 Max. error variable (outer dead band): set manually
7.6.4 Dead time setting
7.6.5 Closing fully/opening fully (end position tolerance for setpoint E1)
7.6.6 Open-close duty (REMOTE MODE) and modulating duty (SETPOINT MODE) selection
7.6.7 Source of setpoint E1: view
7.6.8 Input range of setpoint 1: view/edit
7.7 Process controller (option)
7.7.1 Setting procedure
7.7.2 Process controller activation (Check: Process controller available?)
7.7.3 Proportional gain Kp setting
7.7.4 Reset time Ti setting
7.7.5 Rate time Td setting
AUMATIC AC 01.1/ACExC 01.1 Profibus DP
Actuator controls
Page
33
34
34
35
36
36
37
37
38
38
39
39
40
40
41
41
42
42
43
43
44
45
46
47
48
48
49
49
50
50
52
52
53
53
53
53
54
54
54
55
55
56
57
57
58
58
59
60
61
62
62
63
63
64
3