AUMA AUMATIC AC 01.1 Manual page 4

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Profibus DP
7.7.6 Derivative gain Kd setting
7.7.7 Internal process setpoint setting
7.7.8 Behaviour on loss of the process setpoint (wire break monitoring)
7.7.9 Inverse operation setting
7.7.10 Travel limitation
7.7.11 Reaction monitoring setting
7.7.12 Input range of process setpoint E1: view
7.7.13 Input range of process variable E4: view/edit
7.8 Stepping mode (option)
7.8.1 Display indication: enable view
7.8.2 Stepping mode: switch on or off
7.8.3 Stepping range setting (start and end of stepping mode)
7.8.4 ON and OFF times setting
7.9 Local controls enable function (option)
7.9.1 Selector switch functions: enable/disable
7.10 EMERGENCY STOP function (option)
7.10.1 Description of the functions
7.10.2 Feedback signals on the display
7.10.3 Feedback signals setting via output contacts
7.10.4 Feedback signal setting via LEDs
7.11 Profibus DP interface (option)
7.11.1 Bus address setting (Slaveaddress)
7.12 Redundant bus connection with component redundancy (option)
7.12.1 Configuration check for the second fieldbus interface
7.12.2 Second fieldbus interface setting
7.13 Profibus DP-V1 services (option)
7.14 External inputs for bus (option)
7.14.1 Signals assignation for operation commands
7.15 Combination fieldbus/standard interface (option)
7.16 Monitoring and failure functions
7.16.1 Torque monitoring
7.16.2 Motor protection (thermal monitoring)
7.16.3 Monitoring of the max. number of starts per hour and max. running time per hour
7.16.4 Operating time monitoring
7.16.5 Reaction monitoring
7.16.6 Phase failure monitoring
8 Corrective action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8.1 Fault indications and warning indications
8.1.1 Status indication S0 - faults and warnings
8.1.2 Status indication S1 - fault
8.1.3 Status indication S2 - warnings
8.1.4 Status indication S3 - causes for not ready remote
8.2 Diagnostics
8.2.1 Operating data logging
8.2.2 Diagnostic indications (D) via the display
8.3 Troubleshooting
8.3.1 Problems with position feedback/indication E2 (from actuator)
8.3.2 Display hardly readable or illegible
8.3.3 Actuator does not run
8.3.4 Actuator does only operate from local
8.3.5 Actuator is not switched off by limit seating in direction CLOSE or OPEN
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Parameter index and indications on the display . . . . . . . . . . . . . . . . . . 109
Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
4
Manual
Page
64
65
66
66
67
68
69
69
70
70
71
71
72
73
73
75
75
76
76
76
77
77
78
78
78
79
80
80
83
84
84
85
86
88
89
90
91
91
92
92
94
95
95
97
107
107
107
107
107
107