Mitsubishi Melsec-Q Series User Manual page 527

Number Name Meaning
Stores the
transmission
Transmission
speed specified in
SD100 speed storage
the serial
area
communication
setting.
Stores the
communication
Communication
setting specified in
SD101 setting storage
the serial
area
communication
setting.
Stores the
transmission wait
Transmission
time specifed in
SD102 wait time
the serial
storage area
communication
setting.
Stores the preset
CH1
transmission
transmission
SD105 speed when GX
speed setting
Developer is
(RS-232)
used.
Stores the data
Data sending sending result
SD110 result storage when the serial
area communication
function is used.
Stores the data
Data receiving receiving result
SD111 result storage when the serial
area communication
function is used.
Amount of
Amount of battery
SD118 battery
consumption
consumption
Battery life-
Battery life-
SD119 prolonging
prolonging factor
factor
*3: This applies to Universal model QCPUs except for the Built-in Ethernet port QCPU.
*4: The module whose first 5 digits of serial No. is "10102" or later.
Table12.34 Special register
Explanation
96 : 9.6kbps, 192 : 19.2kbps,
576 : 57.6kbps, 1152 : 115.2kbps
b6
b15 to
Write during RUN setting
0: Disabled
1: Enabled
* : Since the data is used by the system, it is undefined.
0 : No waiting time
10 to 150: Waiting time (unit: ms)
Defaults to 0.
96 : 9600bps, 192 : 19.2kbps,
576 : 57.6kbps, 1152 : 115.2kbps
*: Other than RS-232 connection holds the data at RS-232 connection.
(When disconnected, the default value is 1152.)
Stores the error code at the timeout sending data.
Stores the error code at the time of receiving data.
Displays the current amount of battery consumption.
The value range:1 to 2(Q00UJCPU, Q00UCPU, Q01UCPU,
Q02UCPU, Q03UD(E)CPU, Q04UD(E)HCPU)
1 to 3(Q06UD(E)HCPU)
1 to 4(Q10UD(E)HCPU, Q20UD(E)HCPU,
Q13UD(E)HCPU, Q26UD(E)HCPU)
Stores the factor which makes the battery life-prolonging function valid.
When SD119 is other than 0, the battery life-prolonging function is valid.
b2 b1 b0
b15 to
b0: CPU switch setting
b1: Backup in execution by
CHAPTER12 TROUBLESHOOTING
Set by
(When Set)
384 : 38.4kbps, S (Power-ON or
reset)
b5 b4 b3 b0
to
S (Power-ON or
reset)
Sumcheck presence
0: Absent
1: Present
S (Power-ON or
reset)
384 : 38.4kbps,
S
S (Error)
S (Error)
S (Status
change)
0:No factor
1:Foctor
S (Status
change)
latch data backup function
(to standard ROM)
Corres-
ponding Corresponding
ACPU CPU
D9
New
Q00/Q01
Q00UJ
Q00U
New
Q01U
*4
Q02U
New
Qn(H)
QnPH
New
QnPRH
*3
QnU
Q00/Q01
Q00UJ
Q00U
New
Q01U
*4
Q02U
*4
New
QnU
New QnU
12 - 232
1
2
3
12
6
7
8